Interlogix VDT14330WDM-SC, VDT14330WDM Specsheet

VDT/VDR14330WDM

IFS Digitally Encoded Video with

3 Duplex Data Channels

Overview

The IFS VDT/VDR14330WDM series video transmitter/
receiver and data transceiver supports the simultaneous
broadcast quality transmission of 10-bit digitally encoded
video and three channels of bi-directional data over one
single mode optical fiber. As the level of video performance is
so high, the modules are ideally suited to networks employing
multiple physical layers where video degradation may be a
problem. The modules are universally compatible with major
CCTV camera manufacturers and support all major data
protocols. Each data channel can be set up independently
to support RS-232, RS-422, 2-wire or 4-wire RS-485 data
interfaces. Plug-and-play design ensures ease of installation
requiring no electrical or optical adjustments. Each
transceiver incorporates LED status indicating LED’s for
monitoring of proper system operation. The modules are
available in either stand-alone or rack mount versions.

Application Examples

• High Performance CCTV with PTZ Control plus
two additional data channels for traffic
signalization applications

Standard Features

• 10-Bit Digitally Encoded Video Transmission

• Exceeds RS-250C Short-Haul Transmission

• Ideally Suited to Networks Requiring Multiple Physical
Layers Where Video Degradation May be a Problem

• Three Independent Full-Duplex Data Channels Supporting
RS-232, RS-422, or RS-485 (2-wire or 4-wire) Data Interfaces

• No In-field Electrical or Optical Adjustments Required

• Integrated WDM for Greater Reliability

• Tested and Certified by an Independent Testing Laboratory
for Full Compliance with the Environmental Requirements
(Ambient Operating Temperature, Mechanical Shock,
Vibration, Humidity with Condensation, High-Line/Low-Line
Voltage Conditions and Transient Voltage Protection) of
NEMA TS-1/TS-2 and the Caltrans Specification for Traffic
Signal Control Equipment.

• LED Status Indicators for Monitoring all Critical Operating
Parameters

• NTCIP Compatible

• Hot-Swappable Rack Modules

Digitally Encoded
Video with 3 Duplex
Data Channels

Broadcast quality transmission of
10-bit digitally encoded video and
3 channels of bi-directional data
over one single mode optical fiber.

• Automatic Resettable Fuses on all Power Lines

• Distances up to 43 Miles (69 km)

• Comprehensive Lifetime Warranty

Video

(Coax)

VDT14330WDM VDR14330WDM

1 Fiber

9/125µm SM

up to 37 miles

(60 km)

Video

(Coax)

Control Data

PTZ Control

Control

Data

ifs

International

Fiber

Systems

Incorporated

203.426.1180

ifs

International

Fiber

Systems

Incorporated

203.426.1180

Specifications

Video

Video Input: 1 volt pk-pk (75 ohms)
Bandwidth: 5 Hz - 10.0 MHz
Differential Gain: <2%
Differential Phase: <0.7°
Tilt: <1%
Signal-to-Noise Ratio (SNR): >67 dB @ Maximum Optical Loss Budget

Data

Data Interface: RS-232. RS-422, Sensormatic “Sensornet”, 2 and 4-wire RS-485 w/Tri-State
Data Format: NRZ, NRZI, Manchester, Bi-phase (data channels independently configurable)
Data Rate: DC-100 Kbaud (NRZ)
Bit Error Rate (BER): >1 in 10˚ @ Maximum Optical Loss Budget
Operating Mode: Simplex or Full Duplex

Wavelength 1310/1550 nm, Single Mode

Optical emitter Laser Diode

Number of fibers 1

Connectors

Optical: ST, SC or FC (see ordering information)
Power: Terminal Block with Screw Clamps or Type DB-9P Connector
(specify at time of order)
Video: BNC (Gold Plated Center-Pin)
Data: Type 3 DB-9S

Electrical & Mechanical

Power:
Surface Mount: +12 VDC @ 700 mA (stand alone)
Rack: From Rack
Number of Rack Slots: 2
Current Protection: Automatic Resettable Solid-State Current Limiters
Circuit Board: Meets IPC Standard
Size (in./cm.) (LxWxH)
Surface Mount: 7.0 x 4.0 x 2.0 in., 17.8 x 10.2 x 5.1 cm
Rack Mount: 7.7 x 5.0 x 2.0 in., 19.6 x 12.7 x 5.1 cm
Shipping Weight: < 2 lbs./0.9 kg

Environmental

MTBF: > 100,000 hours
Operating Temp: -40° C to +74° C
Storage Temp: -40° C to +85° C
Relative Humidity: 0% to 95% (non-condensing)†

†May be extended to condensation conditions by adding suffix ‘–C’ to
model number for conformal coating.

Ordering Information

Part Number Optical Pwr. Budget Max. Distance*

Single Mode
9/125µm

Accessories

Options

◆

VDT14330WDM
VDR14330WDM
VDT14330WDM-HP

PS-12VDC 12 Volt DC Plug-in Power Supply (Included)
PS-12VDC-230 12 Volt DC Plug-in Power Supply, 230 VAC Input (Included if specified at time of order)

Add ‘-R3’ to Model Number for R3 Rack Mount - No Charge (Requires R3 Rack purchased separately)
Add ‘-SC’ to Model Number for SC Optical Connector - (For Single Mode Equipment and Rack Mount only)
Add ‘-FC’ to Model number for FC Optical Connector (Single Mode Equipment only)
Add ‘-C’ for Conformally Coated Printed Circuit Boards (Extra charge, consult factory)
Add ‘-HP’ to Model Number for 26 dB Single Mode Optical Power Budget

Description

Video Transmitter/Data Transceiver (1310/1550 nm)
Video Receiver/Data Transceiver (1550/1310 nm)
Video Transmitter/Data Transceiver, High Power

System Design

Fibers Required

1

20 dB

23 dB

37 miles (60 km)

43 miles (69 km)