Interlogix TVP-CWM Installation Instructions Manual
© 2018 United Technologies Corporation. All rights reserved. P/N 1073438-EN • REV B • ISS 15MAY18
Interlogix is part of UTC Climate, Controls & Security, a unit of United Technologies Corporation.
TVP-CWM Compact PTZ Indoor Wall Mount
Installation Instructions
Dimensions
Dimensions
:
125.8 × 80 × 223.9 mm (4.95 × 3.15 ×
8.81 in.)
Weight:
450 g (0.99 lbs.)
Accessories
:
Drill template: 1
pcs
Used to drill
mounting holes.
Drywall anchor
s: 4 pcs
Used to install the
indoor wall mount to the mounting surface.
Screw A: 4 pcs
Used to install the
indoor wall mount to the mounting surface.
Screw B:
3 pcs
Used
to install the mounting plate to the indoor wall mount.
Supported cameras
The compact PTZ indoor plastic wall mount can be used with
following cameras:
IP Compact PTZ Camera: TVP-5101
Installation
To install the TVP-5101 PTZ camera on a mounting surface
using the TVP-CWM:
1. Remove the wall mount mounting plate from the mount by
loosening the screw that locks the mount in place, located
towards the back of the wall mount. Pull the mounting
plate away from the mount. It is held in place by two metal
clips and dimples.
2. Rotate the adapter plate counterclockwise to separate it
from the PTZ camera.
Open
View of adapter plate when
mounted to the PTZ
View of the adapter plate that
goes towards the PTZ
3. Keep in mind that the PTZ pan range is 350 degrees.
Align the cable access hole in the adapter plate with the
access hole in the wall mount. Install the adapter plate to
the wall mount using screw B.
2 / 2 P/N 1073438-EN • REV B • ISS 15MAY18
4. Route the PTZ cable harness through the cable access
hole.
5. Align the PTZ camera with the three clips on the adapter
plate. Rotate the PTZ camera clockwise to secure the
camera to the adapter plate. The three clips on the
adapter plate lock the camera in place.
Open Lock
6. Separate the mounting base (see image below) from the
wall mount.
Using the wall mount mounting base mark the mounting
holes. Make sure that the up arrow on the mounting plate
is pointing up. Provide access for the interconnect cables.
Secure the wall mount mounting base to the mounting
surface with the four A screws (use drywall anchors if the
mounting surface is a wall).
7. Connect the corresponding cables.
Install the camera assembly to the mounting plate by lining
up the two slots in the top of the wall mount with the two
metal clips at the top of the mounting plate. Push down on
the wall mount/PTZ until is snaps into place. Tighten the
screw at the base of the wall mount to lock it in place.
Legal and regulatory information
Trademarks and
patents
The trade names used in this document may be
trademarks or registered trademarks of the
manufacturers or vendors of the respective
products.
Manufacturer
Interlogix.
2955 Red Hill Avenue, Costa Mesa, CA 92626
5923, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
Certification
Product warnings
and disclaimers
THESE PRODUCTS ARE INTENDED FOR
SALE TO AND INSTALLATION BY QUALIFIED
PROFESSIONALS. UTC FIRE & SECURITY
CANNOT PROVIDE ANY ASSURANCE THAT
ANY PERSON OR ENTITY BUYING ITS
PRODUCTS, INCLUDING ANY “AUTHORIZED
DEALER” OR “AUTHORIZED RESELLER”, IS
PROPERLY TRAINED OR EXPERIENCED TO
CORRECTLY INSTALL FIRE AND SECURITY
RELATED PRODUCTS.
For more information on warranty disclaimers and
product safety information, please check
www.firesecurityproducts.com/policy/productwarning/ or scan the following code:
Contact
information and
manuals / tools /
firmware
For contact information and to download the
latest manuals, tools, and firmware, go to the web
site of your region.
Americas: www.interlogix.com
EMEA: www.firesecurityproducts.com
Manuals are available in several languages
Australia/New Zealand: www.utcfs.com.au
Loading...