Interlogix TVJ-JBS User Manual

TVJ-JBS Stainless Steel Junction Box

Dimensions

210 mm (8.27 in.)

248.7 mm (9.79 in.)

229 mm (9.02 in.)

135 mm (5.31 in.)

60 mm

(2.36 in.)

141 mm

(5.55 in.)

174 mm

(6.85 in.)

77.5 mm (3.05 in.)

123 mm (4.84 in.)

Weight:

Drill template: 1

Screw

Used to install the TVJ mounting

Drywall anchor: 7.5 x 24.5 mm (4

Used to install the TVJ mounting

Torx w

Used to remove and

stainless steel junction box.

Sealing plug group A: 4

Used for the depends on cable diameter. Use the correct color for a tight seal.

Sealing plug group B: 4 pcs

Used for the other two holes. diameter. Use the correct color for a tight seal.

Installation Instructions

Specifications

1981 g (4.37 lb.)

ccessories:

pcs

248.7 × 174 × 77.5 mm (9.79 × 6.85 × 3.05 in.)

rench: 1 pcs

tighten the Torx screws on the cover of the

pcs

camera cable harness access hole. Plug color

Black White Blue Black

Plug color depends on cable

: PA5 x 25 mm (4 pcs)

-JBS stainless steel junction box to the

surface.

pcs)

surface along with the screw described above.

-JBS stainless steel junction box to the

Black White Blue Black

Supported Cameras

The stainless steel junction box can be used with following

cameras:

Stainless Steel Dome: TVD-5801, TVB-5802

Installation

To install the junction box:

1. Drill mounting holes in the mounting surface according to the supplied drill template. Insert the four drywall anchors in the mounting surface. Partially tighten down the four mounting screws

2. Unscrew the four screws on the cover of the junction box

DC12V

DC12

Trademarks and patents

Manufacturer

Certification

Product warnings

and disclaimers

For more information on warranty disclaimers and

Contact

information and manuals

For contact information go to: www.interlogix.com

and remove the cover.

6. Tighten the sealing plug group A and group B after

connecting the cables. Reattach the cover of the junction box.

Camera cable harness access hole

3. Align the four slotted mounting holes on the junction box

with the mounting hardware. Secure the junction box to the mounting surface.

4. Route the camera cable harness through the cable access hole on the junction box and tighten the waterproof nut.

5. Use the other cable access holes in the junction box to route the cables into the junction box. Complete the

connections.

Legal and regulatory information

The trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products.

Interlogix.

2955 Red Hill Avenue, Costa Mesa, CA 92626 5923, USA

Authorized EU manufacturing representative:

UTC Fire & Security B.V. Kelvinstraat 7, 6003 DH Weert, The Netherlands

THESE PRODUCTS ARE INTENDED FOR SALE TO, AND INSTALLATION BY, AN EXPERIENCED SECURITY PROFESSIONAL. UTC FIRE & SECURITY CANNOT PROVIDE ANY ASSURANCE THAT ANY PERSON OR ENTITY BUYING ITS PRODUCTS, INCLUDING ANY “AUTHORIZED DEALER”, IS PROPERLY TRAINED OR EXPERIENCED TO CORRECTLY INSTALL SECURITY RELATED PRODUCTS.

product safety information, please check www.firesecurityproducts.com/policy/productwarning/ or scan the following code:

or www.firesecurityproducts.com To get translations for this and other product

manuals go to: www.firesecurityproducts.com

2 / 2 P/N 1073413-EN • REV A • ISS 24JAN18