Interlogix TVD-7125VE-2 User Manual
TruVision TVD-7120VE-2 /
TVD-7125VE-2 Camera
User Manual
P/N 1072794B-EN • REV 1.0 • ISS 17JUN14
r
Copyright © 2014 United Technologies Corporation.
Interlogix is part of UTC Building & Industrial Systems, a unit of
United Technologies Corporation. All rights reserved.
Trademarks and
patents
Trade names used in this document may be trademarks or
registered trademarks of the manufacturers or vendors of the
respective products.
Manufacture
United Technologies Corporation.
2955 Red Hill Avenue, Costa Mesa, CA 92626-5923, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
Certification
N4131
FCC compliance Class A: This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.
Canada This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme
NMB-003 du Canada.
ACMA compliance Notice! This is a Class A product. In a domestic environment this
product may cause radio interference in which case the user may be
required to take adequate measures.
European Union
directives
12004/108/EC (EMC directive): Hereby, UTC Fire & Security
declares that this device is in compliance or with the essential
requirements and other relevant provisions of Directive
2004/108/EC.
2002/96/EC (WEEE directive): Products marked with this symbol
cannot be disposed of as unsorted municipal waste in the European
Union. For proper recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see:
www.recyclethis.info.
Contact information For contact information, see www.utcfireandsecurity.com or
www.utcfssecurityproducts.eu.
Content
Product overview 2
Package contents 2
Features 2
User guidelines 2
Product description 3
Installation 4
Mount the camera 4
Connect the cables 5
Adjust the lens 5
Programming 7
OSD control button 7
Access the Setup Menu 7
Save changes 9
Select the lens type 9
Set the shutter/AGC 9
Set the white balance 11
Set the backlight compensation (BLC) 12
Adjust the picture characteristics 12
Set the ATR level 12
Set the motion detection 13
Set the privacy areas 13
Set the Day/Night mode 14
Set the image noise reduction 15
Set the camera ID 15
Set the sync mode 16
Select the language 17
Reset camera settings 17
Specifications 18
Dimensions 18
Menu tree 19
TruVision TVD-7120VE-2 / TVD-7125VE-2 Camera User Manual 1
Product overview
The TVD-7120VE-2-N(-P)/ TVD-7125VE-2-N(-P) color dome camera uses a
digital signal processor (DSP) to process video signals. The camera includes a
microcontroller to provide high-quality images with high-color reproduction and
sharp pictures.
Package contents
The package contains the following:
• Camera
• Hex wrench
• Drilling template
• Composite video BNC cable
• Screws
• Quick Start Guide
• User Manual (on CD)
Features
The camera includes the following features:
• Super HAD II (hole accumulated diode) technology
• High horizontal resolution 700 TVL
• Smart digital control automatic BLC (backlight compensation)
• Digital WDR (wide dynamic range)
• Advanced auto exposure system for both fixed iris and auto iris lenses to
optimize the amount of light
• Internal and line lock synchronization
• Eight privacy mask areas to protect privacy concerns
• Signal-to-noise ratio better than 62 dB
• Long life and high reliability
• Isolated switching power 12 VDC and 24 VAC
User guidelines
• Program the camera settings as much as possible before mounting the
camera. Take appropriate safety precautions while completing programming
after installation.
• Always use a 12 VDC or 24 VAC UL listed Class 2 power supply to power the
camera.
2 TruVision TVD-7120VE-2 / TVD-7125VE-2 Camera User Manual
• Do not use the camera over the temperature range specifications: -30°C to
+60°C (22°F to 140°F)
• If the light source where the camera is installed experiences rapid, widevariations in lighting, the camera may not operate as intended.
WARNING: To reduce the risk of fire or electronic shock, do not expose the
camera to rain or moisture or open the back of the camera.
Product description
Figure 1: Product description
1. Dome cover
2. Screw hole
3. Base
4. OSD control button
5. Lens
6. IR LED (only for TVD-7125VE-2)
TruVision TVD-7120VE-2 / TVD-7125VE-2 Camera User Manual 3
7. IR LED cover
8. Outlet hole
9. Power supply and video BNC cables
10. Composite video BNC cable
11. Focus adjustment
12. Zoom adjustment
Installation
Please check the package contents and make sure that the device in the
package is in good condition and all the assembly parts are included.
To install the camera, you will need to prepare the mounting surface, mount the
camera, make cable connections, and adjust the lens.
Note: Before installing, please ensure that the mounting surface is strong enough
to withstand three times the weight of the camera. If the mounting surface is not
strong enough, the camera may fall and cause serious damage.
Mount the camera
To mount the camera:
1. Prepare the mounting surface.
2. Remove the dome cover.
3. Secure the camera to the mounting surface with screws.
4. Remove the IR LED cover to adjust the lens and the viewing angle.
4 TruVision TVD-7120VE-2 / TVD-7125VE-2 Camera User Manual
Connect the cables
To make the cable connections:
1. Connect a 12 VDC or 24 VAC power supply to the power input.
2. Connect a coaxial cable from the camera’s BNC connector to a CCTV
monitor or video recording device.
Adjust the lens
The camera is mounted on a pan-tilt-twist (3-axis gimbal) rotating platform so that
it is easy to adjust the camera orientation.
To adjust the lens:
1. Rotate the panning table to adjust the panning position of the camera. The
adjusting range is from 0 to 355 degrees.
2. Rotate the tilting table to adjust the tilting position of the camera. The
adjusting range is from 0 to 75 degrees. Tighten the tilting table lock screw.
3. Rotate the lens to adjust the azimuth angle of the image. The adjusting range
is from 0 to 355 degrees.
Rotation 0-355°
Tilt 0-75°
Pan 0-355°
4. Adjust the lens to obtain the appropriate angle of view and the optimum focus.
Tighten the focus lock lever.
5. Replace the IR LED and dome covers on the camera.
6. Secure the dome cover with screws.
TruVision TVD-7120VE-2 / TVD-7125VE-2 Camera User Manual 5
Loading...