Interlogix TVD-6125VE-2 User Manual

TruVision TVD-6120VE-2 /
TVD

-6125VE-2 Camera

User Manual

P/N 1072541C-EN • ISS 27JUL12

Copyright

©

2012 UTC Fire & Security. All rights reserved.

Trademarks and

patents

The
UTC

Other trade names used in this document may be trademarks or
registered
respective products.

Manufacturer

UTC Fire & Security Americas Corporation, Inc.
2955 Red Hill Avenue, Costa Mesa, CA 92626

Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands

Certification

FCC compliance

Class A:

the limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated i
commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with the instruction m anual, m a y cause harm f ul
interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.

Notice!

product may cause rad
required to take adequate measures.

European Union

directives

12004/108/EC (EMC directive):

declares that this device is in compliance or with the essential
requirements and other

2002/96/EC (WEEE directive):

cannot be disposed of as unsorted municip al was te in the Europ ean
Union. For proper recycling, return this product to your local supplier
upon
designated collection points. For more information see:
www.recyclethis.info.

Contact information

For contact information
www.utcfssecurityproducts.eu

TruVision and Interlogix names and logo are trademarks of
Fire & Security.

trademarks of the manufacturers or vendors of the

-5923, USA

N4131

This equipment has been tested and found to comply with

n a

ACMA compliance

This is a Class A product. In a domestic environment this

io interference in which case the user may be

Hereby, UTC Fire & Security

relevant provisions of Directive 2004/108/EC

Products marked with this symbol

the purchase of equivalent new equipment, or dispose of it at

, see www.utcfireandsecurity.com or

.

Content

Product overview 2

Package Contents 2
Features 2
User guidelines 2
Product description 3

Installation 4

Mount the camera 4
Connect the cables 5
Adjust the lens 5

Programming 7

OSD control button 7
Access the Setup menu 7
Save changes 9
Select the lens type 9
Set shutter/AGC 9
Set white balance 10
Set backlight compensation (BLC) 11
Adjust the picture characteristics 12
Set ATR-EX level 12
Set motion detection 13
Set privacy area 13
Set Day/Night mode 14
Set image noise reduction 15
Set the camera ID 15
Set sync mode 16
Select the language 16
Reset camera settings 16

Specifications 17

Dimensions 17

Menu Map 18

TruVision TVD-6120VE-2 / TVD-6125VE-2 Camera User Manual 1

Product overview

The TVD-6120VE-2-N(-P)/ TVD-6125VE-2-N(-P) color dome camera uses a
digital signal processor (DSP) to process video signals. The camera includes a
microcontroller to provide high-quality images with high-color reprod uc ti on and
sharp pictures.

Package Contents

The package contains the fol l owing:

• Camera

• Hex key

• Drilling template

• Composite video BNC cable

• Screws

• Quick Start Guide

Features

The camera includes the following features:

• Super HAD II (hole accumulated diode) technology

• High horizontal resolution 600 TVL

• Smart digital control automatic BLC (backlight compensation)

• Digital WDR (wide dynamic range)

• Advanced auto exposure system for both fixed iris and auto iris lenses to
optimize the amount of light

• Internal synchronization

• Eight privacy mask areas to protect privacy concerns

• Signal-to-noise ratio better than 52 dB

• Long life and high reliability

• Isolated switching power 12 VDC and 24 VAC

User guidelines

• Program the camera settings as much as possible before mounting the
camera. Take appropriate safety precautions while completing programming
after installation.

• Always use a 12 VDC or 24 VAC UL listed Class 2 power supply to power the
camera.

2 TruVision TVD-6120VE-2 / TVD-6125VE-2 Camera User Manual

1. Dome cover

6. IR LED

7. IR LED cover

12. Zoom adjustment

• Do not use the camera over the temperature range specifications: -10°C to
+50°C (14°F to 122°F)

• If the light source where the camera is installed experiences rapid, wide­variations in lighting, the camera may not operate as intended.

WARNING: To reduce the risk of fire or electronic shock, do not expose the
camera to rain or moisture or open the back of the camera.

Product description

Figure 1: Product description

2. Screw hole

3. Base

4. OSD control button

5. Lens

TruVision TVD-6120VE-2 / TVD-6125VE-2 Camera User Manual 3

8. Outlet hole

9. Power supply and video BNC cables

10. Composite video BNC cable

11. Focus adjustment

Installation

Please check the package contents and make sure that the device in the
package is in good condition and all the assembly parts are included.

To install the camera you will need to prepare the mounting surface, mount the
camera, make cable connections, and adjust the lens.

Note: Before installing, please ensure that the mounting surface is strong enough
to withstand three times the weight of the camera. If the mounting surface is not
strong enough, the camera may fall and cause serious damage.

Mount the camera

To mount the camera:

1. Prepare the mounting surface.

2. Remove the dome cover.

3. Secure the camera to the mounting surface with screws.

4. Remove the IR LED cover to adjust the lens and the viewing angle.

4 TruVision TVD-6120VE-2 / TVD-6125VE-2 Camera User Manual

Rotation 0-355°

Pan 0-355°

Connect the cables

To make the cable connections:

1. Connect a 12 VDC or 24 VAC power supply to the power input.

2. Connect a coaxial cable from the camera’s BNC connector to a CCTV
monitor or video recording device.

Adjust the lens

The camera is mounted on a pan-tilt-twist (3-axis grimbal) rotating platform so
that it is easy to adjust the camera orientation.

To adjust the lens:

1. Rotate the panning table to adjust the panning position of the camera. The
adjusting range is from 0 to 355 degrees.

2. Rotate the tilting table to adjust the tilting position of the camera. The
adjusting range is from 0 to 75 degrees. Tighten the tilting table lock screw.

3. Rotate the lens to adjust the azimuth angle of the image. The adjusting range
is from 0 to 355 degrees.

Tilt 0-75°

4. Adjust the lens to obtain the appropriate angle of view and the optimum focus.
Tighten the focus lock lever.

5. Replace the IR LED and dome covers on t he c amera.

6. Secure the dome cover with screws.

TruVision TVD-6120VE-2 / TVD-6125VE-2 Camera User Manual 5

Note: Ensure that the screws highlighted above with a “ ” have been tightened
securely to prevent water seepage.

6 TruVision TVD-6120VE-2 / TVD-6125VE-2 Camera User Manual

Button

Up

Left

Right
Down

Enter

Programming

Once the camera hardware has been installed, the camera can then be
configured.

Program the camera by attaching a standard video monitor to the system.

To connect the monitor:

1. Plug the monitor output cable to the video monitor output connector.

2. Connect the BNC cable to the video monitor.

3. Press Enter on the OSD menu button to display the Setup menu. See Table
1 for instructions on how to move the cursor.

OSD control button

The on-screen display (OSD) control button (see Figure 1) is a five-direction
joystick that lets you manually control the camera functions. Table 1 below lists
the OSD control button functions and describes their use.

Table 1: Using the OSD control button

direction Description

Moves the cursor upward to select an item

Moves the cursor left to select or adjust the parameters of the selected

item.

Moves the cursor to the right to select or adjust the parameters of the

selected item.

Moves the cursor downward to select an item.

Press the center of the button to display the Setup menu. If the selected

item has its own menu, press the button to enter a submenu.

Access the Setup menu

The Setup menu provides access to the camera configuration options.

TruVision TVD-6120VE-2 / TVD-6125VE-2 Camera User Manual 7

Figure 2: The Setup menu

Table 2: Setup menu description
Menu item Description

Lens Defines autoiris or manual iris.
Shutter/AGC Defines the method of light control.
White Bal Defines the white balance (WB) set up.
Backlight Defines the highlight compensation (HLC) and backlight compensation

(BLC) set up.
Pict Adjust Defines the image quality functions.
ATR Defines the adaptive tone reproduction set up.
Motion Det Defines the motion detection set up.
Privacy Defines privacy mask set up.
Day/Night Defines the day/night (D/N) set up.
NR Defines the digital noise reduction level.
Camera ID Defines the camera ID displayed on-screen.
Sync Displays the current synchronization mode.
Language Defines the language of the OSD.
Camera Reset Resets the camera to factory default settings.
Save All Saves all configuration changes.
Exit Exits the menu and returns to live mode.

To access the Setup menu:

1. Press the OSD control button to access the Setup menu and its submenus.

2. Push the button up/down to move between menu options.

3. Push the button left/right to select an option.

4. Select Next to move to the next Setup menu screen and Back to return to the

previous Setup menu screen.

5. W hen in a sub menu, select Return to return to the previous menu.

6. To exit the Setup menu and return to normal camer a oper ati o n mod e, move

the cursor to Exit at the bottom of the screen and press Enter.

8 TruVision TVD-6120VE-2 / TVD-6125VE-2 Camera User Manual

Save changes

Changes are not saved automatically. When all setup changes to the camera are
done, move the cursor in the Set up menu t o Save All and press Enter to save all
changes made.

Select the lens type

In the Setup menu, go to Lens and select the type of lens used with the camera,
Auto or Manual. Select Auto to set the lens type to auto iris or select Manual for
a manual lens. Manual is default. The Auto Iris or Manual menu appears.

Manual menu:

Select a higher shutter speed value to see movement and a lower value to see
clearer images. The shutter speed available are 1/50, 1/120, 1/250, 1/500,
1/1000, 1/2000, 1/4000 and 1/10000. The AGC value can be set between 6 and

44.8.

Auto iris menu:

Type: Select the drive mode of the lens, DC or Video.
Mode: Select the iris control mode. Auto (automatically controlled depending on

the light), Open (always open), or Closed (always closed).
Speed: When the mode is set to Auto, select the convergence speed of the iris

between 0 and 255.

Set shutter/AGC

In the Setup menu, go to Shutter/AGC and select the required light control
option, Manual or Autoiris. Auto is default. The Manual or Auto menu appears:

TruVision TVD-6120VE-2 / TVD-6125VE-2 Camera User Manual 9

Automatic shutter menu:

Select the parameters for high and low luminance conditions:
High Luminance: Sets the lux level for bright light conditions such as daylight.
Mode: When lens type is AUTO IRIS, you can choose SHUT+AUTO IRIS or

AUTO IRIS mode. When the lens type is manual, only SHUT mode is available.
Brightness: Select the brightness level to which the iris and shutter speed will

adjust automatically. The value ranges from 0 to 255.
Low luminance: Sets the lux level for low light conditions.

Mode: Only AGC is available.
Brightness: Adjust the brightness to x0.25, x0.50, x0.75 or x1.

Manual shutter menu:

Mode: Only Shut/AGC.
Shutter: Set the manual shutter to 1/60(1/50), 1/100(1/120), 1/250, 1/500,

1/1000, 1/2000, 1/4000 or 1/10000.
AGC: Set the gain level. A higher gain compensates for a brighter scene but

noise increases. Manual AGC can be set to 6, 12, 18, 24, 30, 36, 42 or 44.8 dB.

Set white balance

White balance (WB) tells the dome camera what the color white looks like. Based
on this information, the dome camera will then continue to display all colors
correctly even when the color temperature of the scene changes such as from
daylight to fluorescent lighting, for example.

10 TruVision TVD-6120VE-2 / TVD-6125VE-2 Camera User Manual

In the Setup menu, go to White Bal and select the options to be modified:

Menu Item Description

ATW ATW (automatic tracing white balance) limits the color temperature range

between 2,500 to 8,500˚K to reduce excessive compensation for a large
single-color object. Use it to automatically adjust the WB in real time as
the lighting conditions change. It can be used for both indoor and outdoor
locations.

Set the following options:
Speed: Set the compensation speed. A lower value makes the AWB

faster.
Delay CNT: Set the delay time between automatic adjustments of the

AWB. A smaller value increases the frequency rate of AWB.

ATW Frame: X0.5, X1.0, X1.5, X2.0. Default is X2.0.
Environment: Select Indoor (ATW is compensated for low color

temperature such as from incandescent lighting) or Outdoor (ATW is
compensated for high color temperature such as from daylight). Default is
Indoor.

Push Like ATW, the Push function continually monitors/analyzes the color

temperature of the incoming light and corrects the WB. However, Push
has no limits between 1,800 to 10,500˚K so it may over-compensate the
WB for a large single-color object.

User1 This is a fixed white balance that is user-defined by blue and red gain

parameters. Only use this function when there is steady light.
Blue-gain from 0 to 255
Red- gain from 0 to 255

User2 This is a second fixed white balance that is user-defined by blue and red

gain parameters. Only use this function when there is steady light.
Blue-gain from 0 to 255
Red- gain from 0 to 255

Anti CR The anti-color rolling mode function minimizes the color changes over

long periods caused by very small differences between the flicker
frequency of non-inverter fluorescent lights and the drive frequency of the
image sensor devices.

Manual Manually adjust the white balance by blue gain only. The red gain is

automatically adjusted when the blue gain is changed. Only use this
function when there is steady light.

Level UP: Press Enter to increase the WB level.
Level DOWN: Press Enter to decrease the WB level.

Push Lock Press Enter to automatically adjust the white balance to the environment

and lock it at this value.

Set backlight compensation (BLC)

This feature tells the camera to adjust its total exposure (iris and shutter) to
ignore the brightest areas of the image, and instead concentrate on darker areas.

In the Setup menu, go to Backlight and select the options to be modified:
Off: Option is disabled. Default setting.

TruVision TVD-6120VE-2 / TVD-6125VE-2 Camera User Manual 11

BLC (Backlight Compensation): BLC can improve image quality when the
background illumination is high. It prevents the object in the center from
appearing too dark.

HLC (Highlight Compensation): HLC masks strong light sources, giving darker
areas more detail. It is often used to help identify vehicle license plate numbers,
for example.

Adjust the picture characteristics

In the Setup menu, go to Pict Adjust and select the options to be modified.

Set the camera image characteristics such as brightness, contrast, sharpness,
hue, and saturation (called “Gain” here) of the picture. T he par a met ers of each
can be set between 0 and 255.

Use the mirror function to flip the camera image so that it is correctly orientated
for viewing. The image can be flipped vertically, horizontally or horizontally­vertically (180 degrees). Default setting is Off.

Set ATR level

The ATR feature (adaptive tone-curve reproduction) is similar to WDR (wide
dynamic range). It is used when there are both bright and dark areas in the
picture. It helps improve the contrast between objects.

In the Setup menu, go to ATR and select the desired luminance and contrast
parameters.

Luminance: High, medium, low (default)
Contrast: High, midhigh, mid (default), midlow, low

12 TruVision TVD-6120VE-2 / TVD-6125VE-2 Camera User Manual

Set motion detection

Use this function to identify when a moving object passes in front of the camera
to activate an alarm. Up to four motion detection areas can be configured, each
by size and location on-screen.

In the Setup menu, go to Motion Det and select the desired parameters. Default
setting is Off.

Detect sense: Set the sensitivity level for motion detection. A higher value is
more sensitive.

Block Disp: When enabled, any movement detected will be tracked on-screen.
Press Enter to enable or press the button again to cancel it.

Monitor area: When enabled, a square grid is displayed on-screen. It can only
be enabled if Block Disp is also enabled.

Area Sel: Up to four motion-sensitive areas can be set. Set the size and position
of each one.

Set privacy area

Use this function to mask out selected areas of the image. Up to eight pri v ac y
mask areas can be configur ed, each by size and location on-screen.

Note: Only four privacy mask areas can be set when motion detection is
enabled.

In the Setup menu, go to Motion Det and select the desired parameters.

Area Sel: Up to eight privacy masks can be set. Select a mask and then set its
size and position values using Top, Bottom, Left and Right.

TruVision TVD-6120VE-2 / TVD-6125VE-2 Camera User Manual 13

Color: Select the color of the privacy mask.
Transp: Select the transparency shade of the privacy mask. The privacy mask is

fully transparent at value 0.00 and not transparent at 1.00.

Mosaic: Enable this option to mask an ar ea with a mosaic effect. Default is Off.

Set Day/Night mode

In the Setup menu, go to Day/Night and select the desired mode. The Day/Night
mode has two options: Auto, Color and B/W.

Select Color to manually set the camera to color (day) mode.
Select Auto so that the camera can automatically switch between day (color) and

night (black and white) mode.

Auto mode:

Burst: Enable/disable the color burst component of the video signal when the

camera switches to B/W. ON mode maintains the same color signal in B/W so
that the video signal provides better compatibility with certain color equipment.
OFF mode removes the color burst signal B/W video and increase the total TV
lines.

Delay CNT: This is the time in seconds before Day↔Night switches. A long
delay response would be used, for example, to avoid switching from Night to Day
mode when car headlights pass in front of the camera.

Day→Night: Set the threshold level on how dark it should be before switching
from Day to Night mode. Lower (Higher) value makes the camera switched from
Day to Night at lower (higher) illumination

Night→Day: Set the threshold level on how light it should be before switching
from Night to Day mode.

CAUTION: If there is a minimal difference between the Day→Night and
Night→Day values, then camera may switch between Day and Night mode

repeatedly.

14 TruVision TVD-6120VE-2 / TVD-6125VE-2 Camera User Manual

Set image noise reduction

In the Setup menu, go to NR and select the desired mode. Set the noise
reduction strength of the luminance signal (Y).

Set the camera ID

In the Setup menu, go to Camera ID and press Enter to display the menu. The
camera ID displayed on-screen can have up to 40 characters.

Camera ID input line

Command line

To enter a character, move the cursor to the desired character and press Enter to
select it. It appears in the input line. Repeat the process until all characters are
entered.

To move the character input position in the input line, move the cursor in the
command line to ← or → and press Enter.

To clear the input line, move the cursor to CLR and press Enter.
To delete a character in the input line, select the character so that it blinks. Then

move the cursor to CLR on the command line and press Enter.
To position the camera ID on-screen, move the cursor to POS and press Enter.

The menu will then disappear on-screen and the camera ID will be displayed on
the monitor. Use the menu button to move the camera ID to the desired position.
Press Enter. The menu will reappear. Select Return to return to the previous
menu.

TruVision TVD-6120VE-2 / TVD-6125VE-2 Camera User Manual 15

Set sync mode

Use the Sync menu to select the synchronization mode. Only one option is
available, Internal.

Select the language

Use this menu to select the OSD language.
In the Setup menu, go to Language and select the desired language. There are

only two languages available, English and Japanese.

Reset camera settings

Use this menu to reset the camera settings to factory default.
In the Setup menu, go to Camera Reset and press Enter.

16 TruVision TVD-6120VE-2 / TVD-6125VE-2 Camera User Manual

Specifications

Model TVD-6120VE-2-N(P) TVD-6125VE-2-N(P)

Pickup device 1/3" Super HAD CCD II
Total pixels (H NTSC: 811 × 508 / PAL: 795 × 596
Effective pixels NTSC: 768 × 494 / PAL: 752 × 582
Resolution 600 TVL
Synchronization system Internal / Line up
Scanning system 2:1 interlace
IR distance NA 20 m
S/N ratio 52 dB (AGC Off)
Electronic shutter PAL: 1/50 to 1/10,000 s

NTSC: 1/60 to 1/10,000 s
Minimum illumination 0.01 lux (F1.2, AGC X1) 0.00 lux (IR On)
Video output 1 Vpp composite output (75 ohm/BNC)
White balance ATW/ PUSH/ USER1/ USER2/ ANTI CR/ MANUAL/

PUSH LOCK

Lens type 2.8 to 12 mm at F1.4

Angle of view: 91 to 30°
Power supply 24 VAC / 12 VDC 24 VAC / 12 VDC
Current 290mA 375mA
Power consumption Max. 3.5 W Max. 4.5 W
Operating temperature -10 to +50 °C (14 to 122 F°)
Weight 800 g (1.76 lbs)

Dimensions

TruVision TVD-6120VE-2 / TVD-6125VE-2 Camera User Manual 17

Menu Map

18 TruVision TVD-6120VE-2 / TVD-6125VE-2 Camera User Manual