Interlogix TVD-5603, TVT-5603, TVD-5605, TVD-5606, TVB-5606 User Manual

...

TruVision Series 6 IP Camera Configuration Manual

P/N 1073466-EN • REV C • ISS 22JAN19

2019 United Technologies Corporation.

Interlogix is part of UTC

, a unit of United

Technologies Corporation.

Disclaimer

Information in this document is subject to change without notice. No part of this document may be reproduced or transmitted in any form or by any means, electronic or the express written permission of UTC Fire & Security Americas Corporation, Inc.

Trademarks and

patents

T registered trademarks of the manufacturers or vendors of t respective products.

Manufacturer

Interlogix 2955 Red Hill Avenue, Costa Mesa, CA 92626

Authorized EU manufacturing representative: UTC Kelvinstraat 7, 6003 DH Weert, The Netherlands

Certification

Contact information

For contact information www.utcfssecurityproducts.eu

Climate, Controls & Security

mechanical, for any purpose, without

rade names used in this document may be trademarks or

-5923, USA

Building & Industrial System s B.V.

, see www.interlogix.com or

Content

Introduction 3

Product overview 3

Network access 5

Checking your web browser security level 5 Activating the camera 6 Overview of the camera web browser 8

Configuration 10

Configuration menu ov er view 10 Local configuration 11 System time 13 Network settings 14 Recording parameters 22 Video image 25 OSD (On Screen Display) 29 Privacy masks 31 Motion detection alarm s 31 Video tampering 36 Exception alarms 37 Alarm inputs and outputs 38 Face detection 39 Intrusion detection 41 Cross line detection 43 Snapshot parameters 45 NAS settings 47 HDD management 48 Recording Schedule 49

Camera management 52

User management 52 RTSP authentication 54 IP address filter 55 Illegal login lock 56 Restore default settings 56 Import/export a configuration file 57 Upgrade firmware 57 Reboot camera 59

Camera operation 60

TruVision Series 6 IP Camera Configuration Manual 1

Index 65

2 TruVision Series 6 IP Camera Configuration Manual

Introduction

Product overview

This is the configuration manual for the following TruVision IP camera models:

 TVB-5601 (2MPX IP fixed lens bullet camera)  TVB-5602 (4MPX IP fixed lens bullet camera)  TVB-5603 (8MPX IP fixed lens bullet camera)

 TVB-5604 (2MPX IP motorized lens bullet camera)  TVB-5605 (4MPX IP motorized lens bullet camera)  TVB-5606 (8MPX IP motorized lens bullet camera)

 TVT-5601 (2MPX IP fixed lens turret camera, gray)  TVT-5602 (2MPX IP fixed lens turret camera, white)  TVT-5603 (2MPX IP fixed lens turret camera, black)  TVT-5604 (4MPX IP fixed lens turret camera, gray)  TVT-5605 (4MPX IP fixed lens turret camera, white)  TVT-5606 (4MPX IP fixed lens turret camera, black)  TVT-5607 (8MPX IP fixed lens turret camera, gray)

 TVT-5608 (2MPX IP motorized lens turret camera, gray)  TVT-5609 (4MPX IP motorized lens turret camera, gray)  TVT-5610 (4MPX IP motorized lens turret camera, white)  TVT-5611 (8MPX IP motorized lens turret camera, gray)

 TVD-5601 (2MPX IP fixed lens dome camera)  TVD-5602 (4MPX IP fixed lens dome camera)  TVD-5603 (8MPX IP fixed lens dome camera)

 TVD-5604 (2MPX IP motorized lens dome camera)  TVD-5605 (4MPX IP motorized lens dome camera)  TVD-5606 (8MPX IP motorized lens dome camera)

 TVW-5601 (2MPX IP fixed lens dome camera, 2.0 mm)

TruVision Series 6 IP Camera Configuration Manual 3

 TVW-5602 (2MPX IP fixed lens do me camera, gray)  TVW-5603 (2MPX IP fixed lens dome camera, white)  TVW-5604 (2MPX IP fixed lens dome camera, black)  TVW-5605 (4MPX IP fixed lens dome camera, gray)

You can download the softwar e and the foll owing manuals from our w eb site:

 TruVision Series 6 IP Camera Installation Guide  TruVision Series 6 IP Camera Configuration ManualC o nt act information and

manuals /tools /firmware

For contact information and to download the latest manuals, tools, and firmware, go to the web site of your region:

Americas: www.interlogix.com EMEA: www.firesecurityproducts.com

Manuals are available in several languages.

Australia/New Zealand: www.utcfs.com.au

4 TruVision Series 6 IP Camera Configuration Manual

Network access

This manual explains how to configure the camera over the network with a web browser.

TruVision IP cameras can be configured and controlled using Microsoft Internet Explorer (IE) and other browsers. The procedures described use Microsoft Internet Explorer (IE) web browser.

Checking your web browser security level

When using the web browser interface, you can install ActiveX controls to connect and view video using Internet Explorer. However, you cannot download data, such as video and images due to the increased security measure. Consequently you should check the security level of your PC so that you are able to interact with the cameras over the web and, if necessary, modify the Active X settings.

Configuring IE ActiveX controls

You should confirm the ActiveX settings of your web browser.

To change the web browser’s security level:

1. In Internet Explorer click Internet Options on the Tools menu.

2. On the Security tab, click the zone to which you want to assign a web site under “Select a web content zone to specify its security settings”.

3. Click Custom Level.

4. Change the ActiveX controls and plug-ins options that are signed or marked as safe to Enable. Change the ActiveX controls and plug-ins options that are unsigned to Prompt or Disable. Click OK.

— or — Under Reset Custom Settings, click the security level for the whole zone in the

Reset To box, and select Medium. Click Reset. Then click OK to the Internet Options Security tab window.

5. Click Apply in the Internet Options Security tab window.

Windows Internet Explorer

Internet Explorer operating systems have increased security measures to protect your PC from any malicious software being installed.

To have complete functionality of the web browser interface with Windows 7, 8 and 10, do the following:

• Run the browser interface as an administrator in your workstation

• Add the camera’s IP address to your browser’s list of trusted sites

TruVision Series 6 IP Camera Configuration Manual 5

To add the camera’s IP address to Internet Explorer’s list of trusted sites:

1. Open Internet Explorer.

2. Click Tools, and then Internet Options.

3. Click the Security tab, and then select the Trusted sites icon.

4. Click the Sites button.

5. Clear the “Require server verification (https:) for all sites in this zone box.

6. Enter the IP address in the “Add this website to the zone” field.

7. Click Add, and then click Close.

8. Click OK in the Internet Options dialog window.

9. Connect to the camera for full browser functionality.

Activating the camera

When you first start up the camera, the Activation window appears. You must define a high-security admin password before you can access the camera. There is no default password provided.

You can activate a password via a web browser and via TruVision Device Manager to find the IP address of the camera.

Activation via the web browser:

1. Power on the camera and connect the camera to the network.

2. Input the IP address into the address bar of the web browser, and click Enter to enter the activation interface.

Note:

 The default IP address of the camera is 192.168.1.70.  For the camera to enable DHCP by default, you must activate the camera via

TruVision Device Manager. Please refer to the following section, “Activation via TruVision Device Manager”.

3. Enter the password in the password field.

6 TruVision Series 6 IP Camera Configuration Manual

Note: A valid password range must be between 8 and 16 characters. You can use a combination of numbers, lower and upper case letters, and special characters: _ - , . * & @ / $ ? Space. The password must contain characters from at least two of these groups. We also recommend that you reset your password regularly. For high security systems, it is particularly recommended to reset the password monthly or weekly for better protection.

4. Confirm the password.

5. Click OK to save the password and enter the live view interface.

Activation via TruVision Device Manager:

1. Run the TruVision Device Manager to search for online devices.

2. Select the device status from the device list, and select the inactive device.

3. Enter the password in the password field, and confirm it. Note: A valid password range must be between 8 and 16 characters. You can use a

combination of numbers, lower and upper case letters, and special characters: _ - , . * & @ / $ ? Space. The password must contain characters from at least two of these groups. We also recommend that you reset your password regularly. For high security systems, it is particularly recommended to reset the password monthly or weekly for better protection.

4. Click OK to save the password. A pop-up window appears to confirm the activation. If activation fails, confirm that

the password meets the requirements and try again.

5. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or selecting the check box of Enable DHCP.

TruVision Series 6 IP Camera Configuration Manual 7

6. Input the password and click the Save button to activate your IP address modification.

Overview of the camera web browser

The camera web browser lets you view, record, and play back recorded videos as well as manage the camera from any PC with Internet access. The browser’s easy-to-use controls give you quick access to all camera functions. See Figure 1 below.

If there is more than one camera connected over the network, open a separate web browser window for each individual camera.

Figure 1: Web browser window: Live view shown

Name

1. Live view Click to view live video.

2. Playback Click to play back video.

3. Picture Click to search snapshots.

8 TruVision Series 6 IP Camera Configuration Manual

Description

Name

4. Log Click to search for event logs. There are three main types: Alarm, Exception, and

5. Configuration Click to display the configuration window for setting up the camera.

6. Viewer View live video. Time, date and camera name are displayed here.

7. Admin Displays current user logged on.

8. Help Click to find function.

9. Logout Click to log out from the system. This can be done at any time.

10. Live view toolbar

Description

Operation.

Click to start/stop live view Click to manually capture the snapshot Click to manually start/stop recording Click to start/ stop dig it al zo om function Live view with main stream or substream Click to select the third-party plug-in Turn on/off microphone Audio on and adjust Volume/Mute Manual alarm The window size is 4:3 The window size is 16:9 The original window size Self-adaptive window size

TruVision Series 6 IP Camera Configuration Manual 9

Configuration

This chapter explains how to configure the cameras through a web browser. Once the camera hardware has been installed, configure the camera’s settings through

the web browser. You must have administrator rights in order to configure the cameras over the internet.

The camera web browser lets you configure the camera remotely using your PC. Web browser options may vary depending on camera model.

There are two main menus in the configuration panel:

 Local configuration  Camera Configuration

Configuration menu overview

Use the Configuration panel to configure the server, network, camera, alarms, users, transactions and other par a met er s such as up g r adi ng the firmw ar e. S ee Figure 2 below for descriptions of the configuration menus available.

Figure 2: Configuration window (Basic Information tab selected)

10 TruVision Series 6 IP Camera Configuration Manual

System

on page

Security

Network Video/Audio

Image

Alarm/ Storage

Configuration menus Description

Defines device basic information including SN and the current firmware version,

time settings, maintenance, and serial port parameters. See “System time” 13 for further information.

Device No.: It can be used for the SNMP or keypad to differentiate individual devices.

Firmware Version Property: First Character: B-Baseline, C-Customization. Second Character: R-Release, F-Fault Third Character: G1-Platform Fourth Character: 0- Reserved.

Defines who can use the camera, their passwords and access privileges, RTSP

authentication, IP address filter, and telnet access.

Defines the network parameters required to access the camera over the internet.

See “Network settings” on page 14 for further information on the setup.

Defines recording parameters.

Defines the image parameters, OSD settings, overlay text, and privacy mask. See

“Video image” on page 25 for further information on the setup.

Event Defines motion detection, video tampering, alarm input/output, and exception. See

“Alarm inputs and outp uts” on page 38. Defines face detection, intrusion detection, cross line.

Defines recording schedule, storage management, NAS configuration and

snapshot.

Local configuration

Use the Local Configurati on me nu to ma nag e t he protocol type, live view performance and local storage paths. In the Configuration panel, click Local Configuration to display the local configuration window. See Figure 3 below for descriptions of the different menu parame ter s .

TruVision Series 6 IP Camera Configuration Manual 11

Protocol

Latency

Enable Meta

Snapshot

Video File Size Save Videos in Live View to

Save

Save View To

Save Playback To

Save Clips to

Figure 3: Example of the Local configuration window

Parameters Description Live View Parameters

Specify the network protocol used.

Options include: TCP, UDP, MULTICAST and HTTP.

Specify the transmission speed.

Options include: Shortest Delay, Auto or Fluent.

Data Overlay It refers to the rules on your local browser. Specify whether or

not to display the colored marks when motion detection, face detection, and intrusion detection are triggered. For example, when the rules option is enabled and a face is detected, the face will be marked with a green rectangle in live view.

Image Format Choose the image format for a snapshot: JPEG or BMP.

Record File Settings

Specify the maximum file size.

Options include: 256 MB, 512 MB and 1G.

Downloaded Files to Specify the directory for downloaded files.

Specify the directory for recorded files.

Snapshot and Clip Settings

10.

12 TruVision Series 6 IP Camera Configuration Manual

Snapshots In Live

Snapshots during

during Playback

Specify the directory for saving snapshots in live vie w mode.

Specify the directory for saving snapshots in playback mode.

Specify the directory for saving video clips in playback mode.

System time

NTP (Network Time Protocol) is a protocol for synchronizing the clocks of network devices, such as IP cameras and computers. Connecting network devices to a dedicated NTP time server ensures that they are all synchronized.

To define the system time and date:

1. From the menu toolbar, click Configuration > Camera Configuration > System >

Time Settings.

2. From the Time Zone drop-down list, select the time zone that is the closest to the camera’s location.

3. Under Time Settings, select one of the options for setting th e ti me and dat e: Synchronize with an NTP server: Select the NTP enable box and enter the server

NTP address. The time interval can be set from 1 to 1008 0 mi nut es. — or —

Set manually: Enabl e the Manual Time Sync function and then click to set the system time from the pop-up calendar.

Note: You can also select the Sync with computer time check box to synchronize

the time of the camera with the time of your computer.

4. Select Enable DST to enable the DST (Daylight Savings Time) function, and set the date of the DST period.

5. Click Save to save changes.

TruVision Series 6 IP Camera Configuration Manual 13

TCP/IP

Network settings

Accessing the camera through a network requires that you define certain network settings. Use the “Network” menu to define the network settings. See Figure 2 below for further information.

Figure 4: Network window (TCP/IP tab shown)

Menu tabs Description

NIC Type: Enter the NIC type. Default is Auto. Other options include: 10M

Half-dup, 10M Full-dup, 100M Half-dup and 100M Full-dup. DHCP: Enable to automatically obtain an IP address and other network

settings from that server.

IPv4 Address: Enter the IPv4 address of the camera. IPv4 Subnet Mask: Enter the IPv4 subnet mask. IPv4 Default Gateway: Enter the IPv4 gateway IP address. IPv6 Mode: Enter the IPv6 mode: Manual, DHCP or Router

Advertisement. IPv6 Address: Enter the IPv6 address of the camera. IPv6 Subnet Prefix Length: Enter the IPv6 prefix length. IPv6 Default Gateway: Enter the IPv6 gateway IP address. Mac Address: Enter the MAC address of the devices. MTU: Enter the valid value range of MTU. Default is 1500. Multicast Address: Enter a D-class IP address between 224.0.0.0 to

239.255.255.255. Only specify this option if you are using the multicast function. Some routers prohibit the use of multicast function in case of a network storm.

14 TruVision Series 6 IP Camera Configuration Manual

Enable Multicast Discovery: Enable the automatic detection of the

DDNS

PPPoE

Port

NAT NAT (Network Address Translation) is used for network connection. Select

SNMP

for

FTP

HTTPS

QoS

Menu tabs Description

online network camera via private multicast protocol in the LAN. DNS server: Specify the DNS server for your network.

DDNS is a service that maps Internet domain names to IP addresses. It is

designed to support dynamic IP address es, such as thos e assign ed b y a DHCP server.

Spec i fy DynDNS , No-IP or ezDDNS. DynDNS (Dynamic DNS): Manually create your own host name. You will

first need to create a user account using the hosting web site, DynDDNS.org.

No-IP: Enter the address of the NO-IP, host name for your camera, the port number, your user name and password.

ezDDNS: Activate the DDNS auto-detection function to set up a dynamic IP address. The server is set up to assign an available host name to your recorder.

See page 16 for setup information.

Retrieve a dynamic IP address. See page 16 for setup information.

HTTP Po rt: The HTTP port is used for remote internet browser access.

Enter the port used for the Internet Explorer (IE) browser. Default value is

80. RTSP Port: RTSP (Real Time Streaming Protocol) is a network control

protocol designed for use in entertainment and communications systems to control streaming media servers. Enter the RTSP port value. The default port number is 554.

HTTPS Port: HTTPS (Hyper Text Transfer Protocol Secure) allows video to be securely viewed when using a browser. Enter the HTTPS port, value. The default port number is 443.

Server Port: This is used for remote client software access. Enter the server port value. The default port number is 8000.

Ala r m Host IP: Specify the IP address of the alarm host. Ala r m Host Port: Specify the port of the alarm host.

See page 16 for setup information.

5. the port mapping mode: auto or manual. See page 17 for setup information.

SNMP is a protocol for managing devices on networks. Enable SNMP to

get the camera status and parameter related information. See page 17 setup information.

Enter the FTP address and folder to which snapshots from the camera

can be uploaded. See page 17 for setup information.

10.

Enter the email address to which messages are sent when an alarm

occurs. See page 18 for setup information.

Specify the authentication of the web site and its associated web server,

which protects against Man-in-the-middle attacks.

QoS (Quality of Service) can help solve the network delay and network

congestion by configuring the priority of data sending. Enable the option in order to solve network delay and network congestion

by configuring the priority of data sending. See page 20 for setup information.

TruVision Series 6 IP Camera Configuration Manual 15

802.1.X See

Integration p

Menu tabs Description

11.

12.

When the feature is enabled, the camera data is secured and user

authentication is needed when connecting the camera to the network. page 17 for setup information.

If you need to access to the camera through the third party platform, you

rotocol

can enable STD-CGI function. The ONVIF protocol is enabled by default. If you do not need to access the camera through the third party platform, please deselect the checkbox Enable ONVIF.

To define the TCP/IP parameters:

1. From the menu toolbar, click Configuration > Camera Configuration > Network >

TCP/IP.

2. Configure the NIC settings, including the NIC Type, IPv4 settings, IPv6 settings, MTU settings, and Multicast Address.

3. If the DHCP server is available, select DHCP.

4. If the DNS server settings are required for some applications (e.g., sending email), you should configure the Preferred DNS Server or Alternate DNS Server.

5. Click Save to save changes.

To define the DDNS parameters:

1. From the menu toolbar, click Configuration > Camera Configuration > Network >

DDNS.

2. Select Enable DDNS to enable this feature.

3. Select DDNS Type. Three options are available: DynDNS, ezDDNS and NO-IP. Select one of the options:

• DynDNS: Enter the DNSS server address, members.ddns.org (which is used to

notify DDNS about changes to your IP address), the host name for your camera, the port number (443 (HTTPS)), and your user name and password used to log into your DDNS account. The domain name displayed under “Host Name” is that which you created on the DynDNS web site.

• ezDDNS: Enter the host name. It will automatically register it online. You can

define a host name for the camera. Make sure you entered a valid DNS server in the network settings and have the necessary ports forwarded in the router (HTTP, Server port, RSTP port).

• NO-IP: Enter the address of the NO-IP, host name for your camera, the port

number, your user name and password.

4. Click Save to save changes.

To define the PPPoE parameters:

1. From the menu toolbar, click Configuration > Camera Configuration > Network >

PPPoE.

2. Select Enable PPPoE to enable this feature.

3. Enter the user name, password, and confirm the password for PPPoE access.

16 TruVision Series 6 IP Camera Configuration Manual

4. Click Save to save changes.

To define the port parameters:

1. From the menu toolbar, click Configuration > Camera Configuration > Network >

Port.

2. Set the HTTP port, RTSP port, HTTPS port and Server port of the camer a. HTTP Port: The default port number is 80. It can be changed to any port number

that is not occupied. RTSP Port: The default port number is 554. It can be changed to any port number

in the range from 1 to 65535. HTTPS Port: The default port number is 443. It can be changed to any port number

that is not occupied. Server Port: The default server port number is 8000. It can be changed to any port

number in the range from 2000 to 65535.

3. Enter the IP address and port if you want to upload the alarm information to the remote alarm host. Also select the Notify Alarm Recipient option in the normal Linkage of each event page.

4. Click Save to save changes.

To set up the NAT parameters:

1. From the menu toolbar, click Configuration > Camera Configuration > Network >

NAT.

2. Select the check box t o enabl e the NA T function.

3. Select Port Mapping Mode to be Auto or Manual. When you choose Manual mode, you can set the external port as desired.

4. Click Save to save changes.

To define the SNMP parameters:

1. From the menu toolbar, click Configuration > Camera Configuration > Network >

SNMP.

2. Select the corresponding version of SNMP: v1 or v2c.

3. Configure the SNMP settings. The configuration of the SNMP software should be the same as the settings you configure here.

4. Click Save to save changes.

Note: Before setting the SNMP, please download the SNMP software and receive the

camera information via the SNMP port. By setting the Trap Address, the camera can send the alarm event and excepti o n messages to the surveillance center. The SNMP version you select should be the same as that of the SNMP software.

To define the FTP parameters:

1. From the menu toolbar, click Configuration > Camera Configuration > Network >

FTP.

TruVision Series 6 IP Camera Configuration Manual 17

2. Configure the FTP settings, including server address, port, user name, password, directory, and uplo ad type.

Anonymous: Select the check box to enable the anonymous access to the FTP server.

Directory: In the Directory Structure field, select the root directory, main directory and subdirectory . When the main directory is selected, you can use Device Name, Device Number, or Device IP for the name of the directory. When the subdirectory is selected, you can use the Camera Name or Camera No. as the name of the directory.

Upload Snapshot: To enable uploading the snapshots to the FTP server.

3. Click Save to save changes.

To set up the email parameters:

1. From the menu toolbar, click Configuration > Camera Configuration > Network >

Email.

2. Configure the following settings:

Sender: The name of the email sender. Sender’s Address: The email address of the sender. SMTP Server: The SMTP Server, IP address or host name. SMTP Port: The SMTP port. The default is 25. E-mail Encryption: Encrypt via SSL, TLS. NONE is default. Attached Image: Select the check box of Attached Image if you want to send

emails with attached alar m snapshots.

Interval: This is the time between two actions of sending attached snapshots.

18 TruVision Series 6 IP Camera Configuration Manual

Authentication: If your email server requires authentication, select the check box to

use authentication to log in to this server. Enter the login user name and password.

User Name: The user name to log in to the server where the snapshots are

uploaded.

Password: Enter the password. Confirm: Confirm the password. Receiver1: The name o f the first user to be notified. Receiver’s Address1: The email address of user to be noti fi ed. Receiver2: The name o f the second user to b e notified. Receiver’s Address2: The email address of user to be noti fi ed. Receiver3: The name o f the second user to b e notified. Receiver’s Address3: The email address of user to be notified.

3. Click Test to test the email parameters set up.

4. Click Save to save changes.

To set up the HTTPS parameters:

1. From the menu toolbar, click Configuration > Camera Configuration > Network >

HTTPS.

2. To create a self-signed certificate: Click the Create button beside “Create Self-signed Certificate”. Ente r the country,

host name/IP, validity and the other information requested.

TruVision Series 6 IP Camera Configuration Manual 19

+ 47 hidden pages