Interlogix TVD-2402, TVD-4402, TVD-2404, TVD-4404 Installation Manual

© 2015 United Technologies Corporation. All rights reserved. P/N 1072937-EN • REV A • ISS 26MAR15

Interlogix is part of UTC Building & Industrial Systems, a unit of United Technologies Corporation. All rights reserved.

TruVision High Definition TVI Vandal Dome
Installation Guide

Product overview

This is the installation guide for TruVision High Definition TVI
dome TVD-2402/TVD-4402 and TVD-2404/TVD-4404. This

guide describes a standard installation.

Package contents:



Camera with power and

video output cables



4 screws and 4 anchors

for wall or ceiling

installation



Template



3 screws for install the

camera to back box

 Hex wrench

 Monitor output cable



Spare rubber knockout

There is a rubber knockout on the camera
back box. This one is for future use.



Installation Guide



CD

• WEEE and Battery
Disposal

Camera description

1. Dome liner

2. Bubble

3. Lens

4. Power cable

5. CVBS video output cable

(black)

6. TVI video output cable
(grey)

7. Back box

8. DIP switch

9. Menu button

Note:

Please check the camera output settings before setting up a
system. The TVI video output can be only connected to DVR
with TVI signal input. The CVBS output supports the standard
monitor, test monitor, encoder and DVR.

For TVD-2402/TVD-4202, the CVBS and TVI output can not be
performed at the same time, you can use the built-in DIP
switch to select the camera video output.

For TVD-2404/TVD-4404, the built-in DIP switch is used to
enable/disable WDR feature, when WDR feature is enabled,
the CVBS output will be blocked out.

DIP switch

5

4

6

8

1

3

2

9

7

2 / 4 P/N 1072937-EN • REV A • ISS 26MAR15

Installation

To install the camera on a ceiling:

1. Using the template, place it level against the mounting
surface and mark the position of the mounting holes.

2. Following all local codes, drill and prepare the mounting
holes.

3. Remove the camera from its back box.

4. Loosen the three set of screws on the edge of the bubble
with the supplied hex wrench.

5. Remove the bubble and the dome liner.

6. Secure the back box to the ceiling with the supplied
screws.

Note: Please remove the rubber knockout for cable

routing outside of the camera, when required.

7. Using a 75-ohm coaxial video cable, connect the camera

TVI video output and a TVI DVR, and connect a 12 VDC
or 24 VAC power supply to the power cable.

8. Align the camera with the back box and tighten the set
screws to secure the camera to the back box.

7. Adjust the surveillance angle:

1) View the camera image on a monitor.

2) Rotate the panning table to adjust the pan direction [0

to 355°].

3) Loosen the tilting lock screw.

4) Rotate the tilting table to adjust the tilt direction [0 to

90°].

5) Tighten the tilting lock screw.

6) Rotate the camera lens holder [0 to 355°] to adjust the

lens to the surveillance angle.

8. Zoom and focus adjustment.

1) View the camera image using the monitor.

2) Loosen the zoom lever and move the screw between T
(Tele) and W (Wide) to obtain the appropriate angle of
view.

3) Tighten the zoom lock screw.

4) Loosen the focus lever and move the screw between F
(Far) and N (Near) to obtain the optimum focus.

5) Tighten the focus lock screw.

Zoom

Focus

Programming

Programming on TVI output:

Once the camera hardware has been installed, you can
configure the camera settings on the TVI DVR.

Please select PTZ protocol as TruVision Coax and click menu
button to call up the camera menu.

For more details, please see the TVI DVR user manual.

Programming on CVBS output:

Programming on CVBS output, you need to connect a monitor
and a TVS-C200 controller (purchase separately) as following
system figure.

The TVS-C200 has one male BNC output and a female output.
Please connect the male output to camera’s CVBS output and
female output to a monitor.

~

~

~

TVI

TVI

CVBS