Interlogix TVD-4402 User Manual

TruVisio

Vandal Dome Installation

Guide

TVD
TVD-2404/TVD-4404

P/N 1072937-EN • REV A • ISS 12MAR15

n High Definition TVI

-2402/TVD-4402

Content

Product overview 3
Camera description 5
Installation 7
Programming 12
Menu 15

Specifications 17
Legal and Regulatory information 18

2 Installation Guide

Product overview

This is the Pocket Guide for TruVision High
Definition TVI dome TVD-2402/TVD-4402 and TVD­2404/TVD-4404. This guide describes a standard
installation.

Package contents:

 Camera with power

and video output
cables

 Template

Installation Guide 3

 4 screws and 4

anchors for wall or
ceiling installation

 3 screws for install

the camera to back
box

 Hex wrench

 Monitor output

cable

 Spare rubber

knockout

There is a rubber knockout
on the camera back box.
This one is for future use.

 CD

4 Installation Guide

 Installation Guide

• WEEE and Battery
Disposal

Camera description

cable (black)

5

4

6

8

1

3

2

9

7

1. Dome liner

2. Bubble

3. Lens

4. Power cable

5. CVBS video output

Installation Guide 5

6. TVI video output
cable (grey)

7. Back box

8. DIP switch

9. Menu button

Note:

Please check the camera output settings

before setting up a system. The TVI video
output can be only connected to DVR with
TVI signal input. The CVBS output supports

the standard monitor, test monitor, encoder
and DVR.

For TVD-2402/TVD-4202, the CVBS and TVI
output can not be performed at the same time,
you can use the built-in DIP switch to select
the camera video output.

For TVD-2404/TVD-4404, the built-in DIP

switch is used to enable/disable WDR feature,
when WDR feature is enabled, the CVBS

output will be blocked out.

6 Installation Guide

DIP switch

Installation

To install the camera on a ceiling:

1. Using the template, place it level against the
mounting surface and mark the position of the
mounting holes.

Installation Guide 7

2. Following all local codes, drill and prepare the
mounting holes.

3. Remove the camera from its back box.

4. Loosen the three set of screws on the edge of
the bubble with the supplied hex wrench.

5. Remove the bubble and the dome liner.

6. Secure the back box to the ceiling with the
supplied screws.

8 Installation Guide

Note: Please remove the rubber knockout for
cable routing outside of the camera, when
required.

7. Using a 75-ohm coaxial video cable, connect

the camera TVI video output and a TVI DVR,
and connect a 12 VDC or 24 VAC power

supply to the power cable.

8. Align the camera with the back box and tighten
the set screws to secure the camera to the
back box.

Installation Guide 9

7. Adjust the surveillance angle:

1) View the camera image on a monitor.

2) Rotate the panning table to adjust the pan
direction [0 to 355°].

3) Loosen the tilting lock screw.

4) Rotate the tilting table to adjust the tilt
direction [0 to 90°].

5) Tighten the tilting lock screw.

6) Rotate the camera lens holder [0 to 355°]
to adjust the lens to the surveillance angle.

10 Installation Guide

8. Zoom and focus adjustment.

~

~

~

1) View the camera image using the monitor.

2) Loosen the zoom lever and move the
screw between T (Tele) and W (Wide) to
obtain the appropriate angle of view.

3) Tighten the zoom lock screw.

4) Loosen the focus lever and move the
screw between F (Far) and N (Near) to
obtain the optimum focus.

5) Tighten the focus lock screw.

Installation Guide 11

Zoom

Focus

Programming

TVI

Programming on TVI output:

Once the camera hardware has been installed, you
can configure the camera settings on the TVI DVR.

12 Installation Guide

Please select PTZ protocol as TruVision Coax and

TVI

CVBS

click menu button to call up the camera menu.

For more details, please see the TVI DVR user

manual.

Programming on CVBS output:

Programming on CVBS output, you need to connect
a monitor and a TVS-C200 controller (purchase
separately) as following system figure.

The TVS-C200 has one male BNC output and a

female output. Please connect the male output to
camera’s CVBS output and female output to a
monitor.

TVD-2402/TVD-4402

Installation Guide 13

The camera has CVBS and TVI selectable video

output. Please set the built-in DIP switch to CVBS
for viewing the program on a standard monitor.

In such case, its TVI will be blocked out until you
finish the settings and change DIP switch back to
TVI.

TVD-2404/TVD-4404

The camera has the CVBS and TVI dual video

output. The built-in DIP switch is for WDR/CVBS
selection.

Please set the built-in DIP switch to CVBS for
viewing the program on a standard m onitor.

When the programing is finished, you may change
the DIP to WDR to enable the WDR feature. In such
case, the CVBS output will be blocked out.

If the DIP is set as CVBS, the WDR feature will be
disabled, and the camera has CVBS and TVI output

available at the same time.

14 Installation Guide

Menu

TVD-2402/TVD-4402:

Installation Guide 15

TVD-2404/TVD-4404:

16 Installation Guide

Specifications

Power supply

24 VAC/12 VDC

Current

Power
consumption

TVD-2402/ TVD-4402:

Weight
Dimensions

TVD-2402/ TVD-4402:

(net) 641 g / 1.41 lb. (without back box)

Installation Guide 17

12 VDC: Max. 300 mA
24 VAC: Max. 210 mA
TVD-2404/TVD-4404:
12 VDC: Max. 375 mA
24 VAC: Max. 270 mA

12 VDC: Max. 3.5W
24 VAC: Max. 5W
TVD-2404/TVD-4404:
12V DC: Max. 4.5W
24V AC: Max. 6.5W

932 g / 205 lb. (with back box)

Ø145.3 x 124.2 mm
(Ø 5.72 x 4.89 in. )

Legal and Regulatory

information

Class A: This equipment has been tested and found to comply with

erated in a commercial environment. This equipment generates,

and used in accordance with the instruction manual, may cause

Copyright:

© 2015 United Technologies Corporation,

Interlogix is part of UTC Building & Industrial Systems, a unit of

United Technologies Corporation. All rights reserved.

Trademarks and patents:

Trade names used in this document may be trademarks or

registered trademarks of the manufacturers or vendors of the
respective products.

Manufacturer:

Interlogix
2955 Red Hill Avenue, Costa Mesa, CA 92626-5923, USA
Authorized EU manufacturing representative:

UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands

Certification:

N4131

FCC compliance: Class A

the limits for a Class A digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is
op

uses, and can radiate radio frequency energy and, if not installed

18 Installation Guide

harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the
interference at his own expense.

ACMA compliance

Notice! This is a Class A product. In a domestic environment this

product may cause radio interference in which case the user may

be required to take adequate measures.

Canada

This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme

NMB-0330 du Canada.

European Union directives:

12004/108/CE (EMC directive): Hereby, UT C Fire & Security declares

that this device is in compliance with the essential requirements and
other relevant provisions of Directiv e 2004/108/EC.

Contact information:

For contact information, see www.interlogix.com or

www.utcfssecurityproducts.eu

2012/19/EU (WEEE directi ve): Products marked

with this symbol cannot be disposed of as

unsorted municipal waste in the European Union.

For proper recycling, return t his product to your

local supplier upon the purchase of equiv alent new
equipment, or dispose of it at designated coll ection
points. For more inf ormation see:
www.recyclethis.info.

Installation Guide 19