Interlogix TVC-N240-1-N-P, TVC-N220-1-N, TVC-N220-1-N-P, TVC-N240-1-N, TVC-M1220-1-N Installation Manual

TruVision IP Box
Camera Installation
Manual

P/N 1072626A-EN • REV 1.0 • ISS 10APR13

Copyright

© 2013 UTC Fire & Security Americas Corporation, Inc.

Interlogix is part of UTC Climate Controls & Security, a unit of United
Technologies Corporation. All rights reserved.

Trademarks and

patents

The Product Name and logo are trademarks of United Technologies.

Other trade names used in this document may be trademarks or registered
trademarks of the manufacturers or vendors of the respective products.

Manufacturer

UTC Fire & Security Americas Corporation, Inc.
2955 Red Hill Avenue, Costa Mesa, CA 92626-5923, USA

Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands

Certification

N4131

FCC compliance

Class B: This equipment has been tested and found to comply with the limits for

a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.

There is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

ACMA compliance

Notice! This is a Class A product. In a domestic environment this product may

cause radio interference in which case the user may be required to take
adequate measures.

Canada

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-0330 du
Canada.

European Union

directives

12004/108/EC (EMC directive): Hereby, UTC Fire & Security declares that this

device is in compliance with the essential requirements and other relevant
provisions of Directive 2004/108/EC.

2002/96/EC (WEEE directive): Products marked with this symbol cannot be
disposed of as unsorted municipal waste in the European Union. For proper
recycling, return this product to your local supplier upon the purchase of
equivalent new equipment, or dispose of it at designated collection points. For
more information see: www.recyclethis.info.

Contact information

For contact information, see www.interlogix.com or
www.utcfssecurityproducts.eu.

Installation Manual 3 EN

Content

Introduction 3

Product overview 3
Features 4

Installation 4

Installation environment 4
Package contents 5
Cable requirements 5
Camera description 6
Connections 6
Accessing the SDHC card 8
Setting up the camera 8
Mounting the camera on a ceiling 9
Using the camera with TVR 60/ TVN 20/ TVN 40/ LNVR and other systems 10
Using the camera with TruVision Navigator 10

Specifications 10

Pin definitions 11

Introduction

Product overview

This is the user manual for TruVision IP Box Camera models:

- TVC-N220-1-N(-P) (VGA)

- TVC-N240-1-N(-P) (4CIF WDR)

- TVC-M1220-1-N(-P) (1.3 megapixel)

- TVC-M2220-1-N(-P) (2.0 megapixel)

- TVC-M3220-1-N(-P) (3.0 megapixel)

- TVC-M5220-1-N(-P) (5.0 megapixel)

EN 4 Installation Manual

Features

This section describes the camera features.

 Supports TCP/IP, HTTP, DNS, RTP/RTSP and PPPoE protocols

 Programming and setup through a browser interface

 Live viewing over the network

 50/60 Hz selectable flicker control

 Mono, bi-directional audio

 Digital pan/tilt/zoom (PTZ)

 Supports remote upgrades and maintenance

 H.264 video compression with dual capability

 Supports full HD, HD, 4CIF, 2CIF, CIF and QCIF

 SDHC card for local storage

Installation

This chapter provides information on how to install the cameras.

Installation environment

When installing your product, consider these factors:

• Electrical: Install electrical wiring carefully. It should be done by qualified
service personnel. Always use a proper PoE switch or a 12 VDC UL listed
Class 2 or CE certified power supply to power the camera. Do not overload
the power cord or adapter.

• Ventilation: Ensure that the location planned for the installation of the
camera is well ventilated.

• Temperature: Do not operate the camera beyond the specified
temperature, humidity or power source ratings. The operating temperature of
the camera is between -10 to +60°C (14 to 140°F). Humidity is below 90%.

• Moisture: Do not expose the camera to rain or moisture, or try to operate it
in wet areas. Turn the power off immediately if the camera is wet and ask a
qualified service person for servicing. Moisture can damage the camera and
also create the danger of electric shock.

• Servicing: Do not attempt to service this camera yourself. Any attempt to
dismantle or remove the covers from this product will invalidate the warranty