TVC-5125BE-3 Bullet IR
Camera Pocket Guide
Overview
This is the Pocket Guide for TVC-5125BE-3-P/TVC5125BE-3-N Bullet IR Camera. The guide describes a
standard installation.
The camera consists of the following:
• Camera with power and video output cable
• Mounting bracket
• Sunshield
Refer to the figures when performing the camera
setup procedures.
P/N 1072502A • ISS 04JUN12
Figure 1. Parts of the camera
A. Sunshield
B. Video and power cables
C. Mounting bracket
2
Figure 2: Camera front
A. 18 LED IR lights
B. Lens
C. Light sensor
3
Figure 3: Mounting sticker template (mm)
4
Figure 4: Dimensions
Installation
To install the camera:
1. Using the mounting sticker as a template, place it
level against the mounting surface and mark the
position of the mounting holes.
2. Following all local codes, drill and prepare the
mounting holes.
5
3. Securely fasten the mount to the mounting
surface with the appropriate fasteners.
4. If needed, seal all mounting holes so that no
moisture can leak into the mounting surface.
5. Screw the camera into the mounting bracket.
Ensure that the camera is firmly attached to the
bracket.
6. Connect a 75 ohm coaxial video cable to the
video cable, and connect a 12 VDC power supply
to the power cable.
7. Adjust the camera position and angle as
required.
Specifications
Power supply 12 VDC ± 10% / 500mA
Current 60 mA (IR off)
Power consumption 2 W max.
Operating temperature -10to +50 °C
Storage temperature -20to70 °C
Weight 320 g (0.7 lb.)
174 mA (IR on)
(14 to 122°F)
(-4 to +158°F)
6
Dimensions (H × W × L) 55 × 50 × 65 mm
(2.2 × 4.9 × 4.95 in.)
Contact information
For contact information, see www.interlogix.com or
www.utcfssecurityproducts.eu.
Regulatory information
© 2012 UTC Fire & Security. All rights reserved.
Manufacturer
UTC Fire & Security Americas Corporation, Inc.
2955 Red Hill Avenue, Costa Mesa, CA 92626 5923, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
FCC compliance
Class B: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications.
Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
7
ACMA compliance
Notice! This is a Class A product. In a domestic environment
this product may cause radio interference in which case the
user may be required to take adequate measures.
Canada
This Class A digital apparatus complies with Canadian ICES-
003.
Cet appareil numérique de la classe A est conforme à la
norme NMB-0330 du Canada.
Certification
N4131
European Union directives
12004/108/EC (EMC directive): Hereby, UTC Fire & Security
declares that this device is in compliance with the essential
requirements and other relevant provisions of Directive
2004/108/EC.
2002/96/EC (WEEE directive): Products
marked with this symbol cannot be
disposed of as unsorted municipal waste in
the European Union. For proper recycling,
return this product to your local supplier
upon the purchase of equivalent new
equipment, or dispose of it at designated
collection points. For more information see:
www.recyclethis.info.
8
Loading...