Interlogix TVC-5120-1 User Manual

TVC-5120-1 Box Camera
Pocket Guide

Overview

This is the pocket guide for TVC-5120-1-P / TVC­5120-1-N Box Camera. It is used indoors. However, if
installed in a housing, it can be used outdoors. The
guide describes a standard installation.

The camera consists of the following:

 Camera body

 CCD protection cap

 Spare lens connector (male)

Refer to the figures in the front of the guide when
performing the camera setup procedures.

Note: Check the package and contents for visible
damage. If any components are damaged or missing,
do not attempt to use the unit, contact the supplier
immediately. If the unit must be returned, it must be
shipped back in its original packaging.

P/N 1072501A • ISS 20SEP12

1: Setting the lens mode

1. Camera

2. Autoiris lens connector

3. Autoiris lens plug

4. Lens (Autoris lens shown. Manual lens has no
cable)

5. C-mount adaptor

6. DC-type autoiris lens leads: Damping coil
positive (A) and negative (B), Driving coil
positive (C) and negative (D)

2

2: Connecting power

3: Recommend DIP switch settings

Fixed lens: DC iris lens:

3

Installation

To install the camera:

1. Connect a coaxial cable terminated with BNC
connectors between the VIDEO OUT connector
of the camera and the video in connector on a
monitor, multiplexer, switcher, or other standard
video device.

2. To attach the lens, please refer to the
instructions that came with the lens. See Figure 1
on page 1 for guidance.

Note: If you are using a C-mount lens, screw on
the provided C-mount adapter. For optimal
performance, use an auto iris lens.

3. To connect power, loosen the DC12V and GND
terminal screws on the terminal block using a
screwdriver. Connect a universal 12 VDC power
supply to the terminal block. Retighten the
terminal screws until snug, ensuring that the
power leads are secure. Supply power to the unit
by plugging the power supply into a proper
source.

The power LED illuminates to show that the
camera is receiving power. If it does not
illuminate, check the terminal block connections
and the power source

4

4. Set the DIP switches. See the table below and

Figure 3 on page 3 for the recommended
settings.

Item Description Remark

AI Auto Iris For autoiris lens only, the

AE Auto

Electronic
shutter

FLK Flickerless Flickerless mode avoids

BLC Back Light

Compensation

shutter is fixed 1/50 (PAL)

For fixed lens. As the iris
is fixed, the camera
automatically sets the
optimum shutter speed.

interference from light
sources (recommended
for DC-iris lenses only ).

Selectively amplifies parts
of the image to
compensate for large
contrast differences when
only a portion of the
image is brightly lit.

5

Specifications

Power supply 12 VDC

Current 85 mA

Power consumption 1 W max.

Operating temperature -10to +50 °C

Storage temperature -20to70 °C

Weight 305 g (0.67 lb.)

Dimensions (H × W × L) 56 x 50 x 125 mm

(14 to 122°F)

(-4 to +158°F)

(2.2 x 4.9 x 4.95 in.)

Contact information

For contact information, see www.interlogix.com or
www.utcfssecurityproducts.eu.

Regulatory information

© 2012 UTC Fire & Security. All rights reserved.

Manufacturer

UTC Fire & Security Americas Corporation, Inc.
2955 Red Hill Avenue, Costa Mesa, CA 92626 5923, USA
Authorized EU manufacturing representative:

6

UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands

FCC compliance

Class B: This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications.
Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.

ACMA compliance

Notice! This is a Class A product. In a domestic environment
this product may cause radio interference in which case the
user may be required to take adequate measures.

Canada

This Class A digital apparatus complies with Canadian ICES-

003.
Cet appareil numérique de la classe A est conforme à la
norme NMB-0330 du Canada.

Certification

N4131

European Union directives

12004/108/EC (EMC directive): Hereby, UTC Fire & Security
declares that this device is in compliance with the essential
requirements and other relevant provisions of Directive

7

2004/108/EC.

8

2002/96/EC (WEEE directive): Products
marked with this symbol cannot be
disposed of as unsorted municipal waste in
the European Union. For proper recycling,
return this product to your local supplier
upon the purchase of equivalent new
equipment, or dispose of it at designated
collection points. For more information see:
www.recyclethis.info.