Interlogix TVC-2401, TVC-4401, TVB-4405, TVB-4406, TVB-2405 User Manual

TruVision HD-TVI 1080P
Camera Configuration
Manual

P/N 1073162-EN • REV A • ISS 31MAR16

Copyright

©

2016 United Technologies Corporation. All rights reserved.

Interlogix is part of UTC Climate, Controls & Security, a unit of United
Technologies Corporation.

Trademarks and

patents

T
United Technologies.

Other trade names used in this document may be trademarks or
registered trademarks of the manufacturers or vendors of the
respective products

Manufacturer

I
2955 Red Hill Avenue, Costa Me

Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands

Contact information

For contact information
www.utcfssecurityproducts.eu

t

For contact information, see www.interlo
www.utcfssecurityproducts.eu

he TruVision and Interlogix names and logos are trademarks of

.

nterlogix

sa, CA 92626-592 3, U SA

, see www.interlogix.com or

.

Customer suppor

gix.com or

Content

Introduction 2

Programming 3

Using the camera Menu button 3
Using a TVI output 3
TVS-C200 CVBS OSD controller 4

Menu trees 6

TVB-2403/4403 and TVD-2403/4403 cameras 6

HD-TVI 1080P IR Bullet Cameras 2
HD-TVI 1080P IR Dome Cameras 2
HD-TVI 1080P Box Cameras 2

TVC-2401/4401 cameras 6
TVB-2404/4404, TVB-2405/4405, TVD -24 04/4404 and TVD-

2405/4405 cameras 7

TVB-2406/4406 cameras 7

Configuration 8

Video Out 8
Languages 8
Setup 8

Smart Focus 8
Scene 8
Lens 8
Exposure 9
Backlight 10
White Bal ance 11
Day & Night 12
NR 13
Special 14
Adjust 17
Reset 18
Exit 18

TruVision HD-TVI 1080P Camera Configuration Manual 1

Introduction

This is the configuration manual for following camera models:

HD-TVI 1080P IR Bullet Cameras

 TVB-2403 (1080P TVI Bullet Camera, Fixed Lens, IR, PAL)
 TVB-4403 (1080P TVI Bullet Camera, Fixed Lens, IR, NTSC)
 TVB-2404 (1080P TVI Bullet Camera, VF Lens, IR, PAL)
 TVB-4404 (1080P TVI Bullet Camera, VF Lens, IR, NTSC)
 TVB-2405 (1080P TVI Bullet Camera, Motorized Lens, IR, PAL)
 TVB-4405 (1080P TVI Bullet Camera, Motorized Lens, IR, NTSC)
 TVB-2406 (1080P TVI Bullet Camera, Motorized Lens, IR, PAL)
 TVB-4406 (1080P TVI Bullet Camera, Motorized Lens, IR, NTSC)

HD-TVI 1080P IR Dome Cameras

 TVD-2403 (1080P TVI Dome Camera, Fixed Lens, IR, PAL)
 TVD-4403 (1080P TVI Dome Camera, Fixed Lens, IR, NTSC)
 TVD-2404 (1080P TVI Mini Dome Camera, VF Lens, IR, PAL)
 TVD-4404 (1080P TVI Mini Dome Camera, VF Lens, IR, NTSC)
 TVD-2405 (1080P TVI Dome Camera, Motorized Lens, IR, PAL)
 TVD-4405 (1080P TVI Dome Camera, Motorized Lens, IR, NTSC)

HD-TVI 1080P Box Cameras

 TVC-2401 (1080P TVI Box Camera, PAL)
 TVC-4401 (1080P TVI Box Camera, NTSC)

2 TruVision HD-TVI 1080P Camera Configuration Manual

Button direction

Iris+

Up

Left

Right
Down

Zoom

Focus

Programming

Once the camera hardware has been installed, the camera can be configured
using the built-in OSD button, a TVI DVR menu, or the OSD TVS-C200 controller
(purchased separately).

Note: TVC-2401/4401 does not support the TruVision TVS-C200 OSD controller.

Using the camera Menu button

For the cameras with built-in OSD button, please press the Menu button to call
up the OSD menu and select an OSD item.

Press the button up/down to move the cursor up or down to an OSD item.
Press the button left/right to move the cursor left or right to adjust the value of a

selected OSD item
For more details, please refer to the TVI camera installation manuals.

Using a TVI output

Programming over the camera’s TVI output can be done via the connected TVI
DVR.

Access the PTZ menu of the connected DVR, select TruVision-Coax protocol
and use the PTZ control panel to configure the camera.

Table 1: Using the OSD control button

Description

Click Iris+ to access to the camera OSD menu and select an OSD item.

Moves the cursor upward to select an item

Moves the cursor left to select or adjust the parameters of the selected

item.

Moves the cursor to the right to select or adjust the parameters of the

selected item.
Moves the cursor downward to select an item.
Adjust the camera zoom in and zoom out

Adjust the camera focus

Note:
TVB-2405/TVB-4405 and TVD-2405/TVD-4405 have motorized lenses. Use the

ZOOM and FOCUS buttons to adjust its zoom and focus.
TVB-2406/TVB-4406 camera has auto-focus capability . When this feature is

enabled, the camera can adjust itself to achieve the best focus automatically.

TruVision HD-TVI 1080P Camera Configuration Manual 3

For more details, refer to the TVI DVR user manual.

TVS-C200 CVBS OSD controller

Interlogix offers two different versions of the OSD controller: the TVS-C100
controller and the TVS-C200 controller. Please choose the corresponding
controller by referring to the product datasheets.

The cameras listed in the “Introduction” section support TruVision Coax OSD
control protocol and require the TVS-C200 for OSD control.

The TVS-C200 is used to program the camera’s 960H CVBS output, not for the
TVI video output. Programming the camera’s TVI output can be done via a TVI
DVR.

The TVS-C200 has four buttons for the camera function selection and control.
Figure 1 below lists the OSD control button functions and describes their use.

Figure 1: TVS-C200 controller

Indicator light Arrow keys

Note: Before using the controller, check that the controller is powered. Two AAA
batteries are required for the controller to work properly.

The Setup menu provides access to the camera’s configuration options. Use the
TVS-C200 controller to access the camera’s Setup menu and select the
configuration options.

To set up and configure the camera:

1. Connect a video monit or to one of the BNC connectors of the controller.

2. Connect the camera’s 960H CVBS output to a BNC connector.

3. Press the OK button for a few seconds to display the Setup menu. See Table
2 for instructions on how to move the cursor.

4 TruVision HD-TVI 1080P Camera Configuration Manual

Button

Up

Left

Right
Down

OK

Table 2: Using the OSD control button

direction Description

Moves the cursor upward to select an item

Moves the cursor left to select or adjust the parameters of the selected

item.

Moves the cursor to the right to select or adjust the parameters of the

selected item.

Moves the cursor downward to select an item.

Press the red button for few seconds to display the Setup menu. If the

selected item has its own menu, press the button to enter a submenu.

TruVision HD-TVI 1080P Camera Configuration Manual 5

Menu trees

The menu trees of the TruVision 1080P TVI cameras are shown below.

TVB-2403/4403 and TVD-2403/4403 cameras

TVC-2401/4401 cameras

6 TruVision HD-TVI 1080P Camera Configuration Manual

TVB-2404/4404, TVB-2405/4405, TVD-2404/4404 and TVD­2405/4405 cameras

TVB-2406/4406 cameras

TruVision HD-TVI 1080P Camera Configuration Manual 7

Configuration

This section describes how to set up the menu settings.

Video Out

Select PAL or NTSC.

Languages

Select one of the languages available:
English, Japanese, CHN1, CHN2, Korean, German, Frenc h , It al ian, Spani s h,

Polish, Russian, Portuguese, Dutch, Turkish, Hebrew or Arabic.

Note: The TVB-2406/4406 camera only supports English and Chinese.

Setup

Smart Focus

Enable Smart Focus. Use this feature to remotely sharpe n th e focus of a
lens. When the feature is enabled and you change the focus of a lens, the
focus number on-screen changes and the focus automatically adjusts to the
highest value to obtain the best focus quality.

Note: TVB-2403/4403, TVB-2406/4406 and TVD-2403/4403 cameras do not
support this feature.

Scene

Select INDOOR, OUTDOOR, INDOOR1 or LOW-LIGHT depending on the
installed environme nt.

Note: The TVB-2406/4406 camera only support INDOOR and OUTDOOR.

Lens

Select as lens mode MANUAL or MANUAL/DC depending on the
characteristics of the camera lens.

For cameras with a varifocal lens, this option is unavailable.
For box cameras, select the lens setting according to the lens type used,

Manual or DC.
For cameras with a motorized lens, use the following settings:

TVB-2406/4406 and TVB-2406/4406: 5 to 50 mm. Other motor ized lenses are
not supported.

Select the following options under the Lens menu:

8 TruVision HD-TVI 1080P Camera Configuration Manual

EXPOSURE

1. SHUTTER AUTO

2. AGC OFF

3. SENS-UP ---

4. BRIGHTNESS ---|------ 40

5. D-WDR OFF

6. DEFOG OFF

7. RETURN RET

ZOOM SPEED Move the cursor left/right to adjust the zoom speed.
PRESET Set the lens pre-set, delete or call pre-conf igur ed lens preset. A total

of 64 presets can be set.

FOCUS MODE Select Manual, Auto, or Trigger mode.

Auto mode: The camera focuses automatically.
Manual mode: Click Zoom+ and Zoom- to focus.

Trigger mode: The image will not refocus if it is changed.
LENSINIT Lens initialization. Reset the lens to calibrate it.
AFLIMIT Auto Focus Limit. Select the minimum auto focus distance: 20 m,

10 m, 6 m, 3 m, 1.5 m, 1 m, 30 cm, or 10 cm.
ZOOM VIEW Display the zoom factor on the OSD.

Exposure

Select as exposure mode MANUAL or IRIS-PRI (Iris Priority). This function is
only available for the TVB-2406/4406 camera.

Only the TVB-2406/4406 camera supports the lens auto-focus function.

Note: When Manual is selected, the SENS-UP settings are disabled. When

IRIS-PRI is selected, SHUTTER and AGC settings are disabled.

Select the following options under the Exposure menu:

SHUTTER

Set the shutter speed. The options available to select are:

1/30, 1/60, 1/90, 1/100, 1/125, 1/180, 1/195, 1/215, 1/230, 1/250,

1/350, 1/500, 1/725, 1/1000, 1/1500, 1/2000, 1/3000, 1/4000, 1/6000,

1/10000, 1/20000, or 1/30000.

For other cameras, the options available to select are: AUTO,

1/25(1/30), 1/50(1/60), FLK, 1/200(1/240), 1/400(1/480), 1/1000,

1/2000, 1/5000, 1/10000 or 1/50000.
AGC Automatic Gain Control.

SENS-UP Select OFF/AUTO to disable/enable the camera to increase exposure

BRIGHTNESS Select a value to increase the image brightness. Value range is 1 to

TruVision HD-TVI 1080P Camera Configuration Manual 9

Automatically adjust the image qua lity in low light conditions. Value

range is from 1 to 15. Selec t a higher value in lo w light condit ions.

times on a signal frame in low light conditions.

Note: SENS-UP is selectable only when Shutter is set to AUTO or

1/30.

100. The higher the value, the brighter the image.

Note: This function is disabled if D-WDR is enabled.

DEFOG

1

.

POS/

SIZE



2

.

GRADATION LOW

3.

DEFAULT



4

.

RETURN RET

BLC

1. GAIN MIDDLE

2. AREA 

3. DEFAULT 

4. RETURN RET

WDR BRIGHT: Set the brightness from 0 to 100. The higher the

D-WDR Digital Wide Dynamic Range.

Select ON/OFF to enable /disable the function. It helps to balance the
brightness level of the whole image.

Note: When D-WDR is enabled, the brightness function is disabled.

DEFOG During foggy or rainy weather, the camera image becomes hazy. The

defog function can increase the image contrast and brightness level
to show more detail.

Note: Enabling the defog function increases the contrast of the
image. It is recommended to set Defog to OFF during normal
weather.

POS/SIZE: Set the position and size of the defogged area.
GRADATION: Set LOW, MIDDLE or HIGH for the defog gradation.
DEFAULT: Restore the defog settings back to default.

Backlight

Select the following options under the Backlight menu:

BLC

Backlight compensation (BLC) improves image quality when the
background illumination is high. It prevents the object in the center of
the image from appearing too dark.

Select OFF, BLC, WDR or HSBLC to improve image quality.

BLC submenus:
GAIN: Set the gain as High, Middle, or Low. The higher the gain

value, the clearer the image.
AREA: Press direction buttons to define the BLC position and size.
DEFAULT: Restore the BLC settings back to default.

WDR Wide Dynamic Range. It provides clear images when there are both

very bright and very dark areas on the image.
GAIN: Set the gain as High, Middle, or Low. The higher the value, the

10 TruVision HD-TVI 1080P Camera Configuration Manual

clearer the image.

value, the brighter the image.

WDR OFFSET: Set the offset from 0 to 100. The higher the value,
the brighter the dark area of the image.

HSBLC Highlight Suppression Backlight Compensation.

Use this function to mask strong light sources across a scene and
improve image quality. There can be up to four mask areas
configured.

SELECT: Select an HSBLC area.
DISPLAY: Select ON to enter a popup screen. Press the direction

buttons to define the area position and si ze .
LEVEL: Select the brightness level between 0 and 100. If the

brightness level is higher than the level you set, HSBLC is enabled.
MODE: Select ALL DAY or NIGHT. In ALL DAY mode, HSBLC works

all day. In NIGHT mode HSBLC onl y work s at night.
BLACK MASK: Select the BLACK MASK status as ON or OFF. When

it is set to ON, the HSBLC is enabled. When it is set to OFF, the
HSBLC function is disabled.

DEFAULT: Select to restore the HSBLC area settings to default (see
below).

White Balance

White balance tells the camera what the color white looks like. Based on this
information, the camera will then continue to display all colors correctly even
when the color temperature of the scene changes such as from daylight to
fluorescent lighting, for example.

Select MANUAL, ATW (Auto-tracking White Balance), or AWC→SET.
Select the following options under the White Balance menu:

TruVision HD-TVI 1080P Camera Configuration Manual 11

MANUAL WB

BLUE ---|------

51
RED ---|------ 50
RETURN RET

AUTO

1. DELAY -------

|--8 0

2

. D-

>N(AGC

) -------|--8 0

3

. N->D(AGC) -------|--8 0

4. RETURN RET

MANUAL Adjust the white balance by customizing the Blue and Red value,

which range from 1 to 100.

ATW Select ATW for the white balance to be automatically adjusted

according to the scene illumination.

AWC→SET If enabled, this function will only adjust the WB once. It is best used

in a stable environment.

Day & Night

Select Color, B/ W, EXT and AUTO to switch between day and night mode.
Note: AUTO mode of the TVB-X406 camera is the similar to EXT mode of the

other cameras (TVC-2401/4401, TVX-2403/4403, TVB-X404/X 405, and TVD­X404/X405). You can enable/disable IR in EXT mode or TRIGGER mode. The
TVC-X401 camera supports both EXT and AUTO mode; configure the mode in
AUTO mode.

AUTO The image switches from color to B/W or from B/W to color

automatically. The switching threshold value is adjustable.
AUTO mode is supported by the TVC-2401/4401 and TVB-

2406/4406 cameras.

DELAY: Select the delay before camera switches between Day/Night
mode when the light condition reaches configured threshold. This
function can effectively prevent Day/Night switches caused by
occasional illumination changes.

D->N (AGC): Define the Day/Night switch threshold value from
between 0 and 100.

N->D (AGC): Define the Night/ Day switch threshold value from

between 0 and 100.
COLOR The image is in continuous color day mode.
B/W The image is in continuous black and white night mode. The IR LED

12 TruVision HD-TVI 1080P Camera Configuration Manual

turns on when the lighting conditions are poor.

3D SMART NR

1. SENSITIVITY -------|-- 80

2. RETURN RET

EXT The image switches from color to B/W or from B/W to color

automatically according to the light conditions.

TRIGGER This function is only available with the TVB-2406/4406 camera.

Select Enable/Disable to turn the IR LED ON/OFF.

NR

Noise reduction (NR) reduces noise, especially in low light conditions, and
improves image quality.

Select the following options under the NR menu:

2D NR Select ON/OFF to enable/disable the feature. It reduces the noise in

a single frame to get a clearer image at night.

3D NR This function processes the noise reduction between two image

frames instead of on ly in one frame. It can decrease the noise effect,
especiall y in night mode. However, this function is not recommended
for moving objects.

SMART NR: Set SMART NR to ON/OFF to enable/disable this
function. Enable 3D SMART NR to enter the 3D Smart NR interface
and adjust the sensitivity level. The sensitivity level ranges from 0 to

100.

TruVision HD-TVI 1080P Camera Configuration Manual 13

START AGC: Automatic Gain Control automatically adjusts the
camera’s sensitivity in low light conditions. Set a threshold to enable
AGC.

END AGC: Set a threshold to disable AGC.

SPECIAL

1

. CAM TITLE ON



2. D-EFFECT



3. MOTION OFF
4

. PRIVACY OFF

5.

DEFECT



6.

RS

485



7.

RETURN RET

CAM TITLE

0 1 2 3 4 5 6 7 8 9

A B C D E F G H I J K

L M N O P Q R S T U V

W X Y Z ▶ → ←↑ ↓ ( )

¯ - _ ■ / = & : ~ , .

← → CLR POS END

C

A

M E R

A

0

1

_ _ _

D-EFFECT

1. FREEZE OFF

2. MIRROR OFF

3. D-ZOOM OFF

4. SMART D-ZOOM OFF

5. NEG. IMAGE OFF

6. RETURN RET

Special

Use this menu to configure the camera name, digital effect settings for the image,
motion detection, privacy mask, dead pixel correction, as well as check the
camera version.

Select the following options under the Special menu:

CAM TITLE Set the camera name by enabling this function to enter the editing

interface. Up to 15 characters can be entered.

ON: Display and enter the camera title.

OFF: Do not display the camera title.

D-EFFECT Use this menu to freeze the image, inverse the image, set digital

14 TruVision HD-TVI 1080P Camera Configuration Manual

zoom, and create a negative image.

FREEZE: Set ON to freeze the image when the function is enabled.

Note: The mirror function is disabled when FREEZE is ON.

MIRROR: It mirrors the image so you can see it inversed. Select

OFF, MIRROR, V-FLIP, and ROTATE.

OFF: Function is disabled.
MIRROR: Image flips 180 degrees horizontally.

V-FLIP: Image flips 180 degrees vertically.

D-ZOOM

1. D-ZOOM x 2.0

2. PAN & TILT



3. DEFAULT 

4. RETURN RET

SMART D

-

ZOOM

1

.

SELECT AREA1

2.

DISPLAY ON

3. SENSITIVITY ---

|----31

4

.

D-ZOOM x

2.0

5

.TIME --

|-------3

6

.DEFAULT

7.

RETURN RET

SENSITIVITY: Set the value according to the situation. The range is

ROTATE: Image flips 180 degrees both horizontally and
vertically.

D-ZOOM: Set the digital zoom ON to enlarge the image by creating
pixels through interpolation.

D-ZOOM: Set the zoom factor between 2 and 62.
PAN & TILT: Define zoom area in PAN & TILT menus.
DEFAULT: Set to restore D-ZOOM back to the default settings.

SMART D-ZOOM: When the feature is enabled, the image of the
detected moving object in the pre-defined area will be enlarged . The
D-Zoom area, sensitivity, and zoom factor are configurable.

Note: D-Zoom and Smart D-Zoom cannot take effect
simultaneously.

Up to two areas can be set in one camera. Move the cursor
up/down to select the area.

NEG. IMAGE: Negative image. Select ON to reverse bright and dark
areas of the image.

Note: When WDR is enabled, D-Zoom and Smart D Zoom cannot be
configured.

MOTION Define the settings to detect movement and trigger an alarm.

SELECT: Select the MOTION area number.

TruVision HD-TVI 1080P Camera Configuration Manual 15

DISPLAY: Set ON to enter to define the position and size of the
motion detection area.

from 0 to 60. The higher the value, the higher the sensitivity level to

DEFECT

1. LIVE DPC AUTO
2

. STATIC DPC ON

3. RETURN RET

trigger an alarm.

Note: Branch movement, rain drops, snowflakes, flashing lights in

the defined area may be detected and trigger a false alarm. In such

cases, adjust the sensitive value.

MOTION VIEW: Enabled this feature to trigger a flickering

transparent red mosaic on the detected area when motion is

detected. Set it to OFF to disable.

DEFAULT: Select to restore settings back to default.
PRIVACY Privacy masks let you conceal sensitive areas (such as neighboring

windows) to protect them from view on the monitor screen and in the

recorded video. Up to eight privacy areas can be configured.

SELECT: Select a PRIVACY area.

DISPLAY: Set the status to INV, MOSAIC, COLOR or OFF.

INV. (invisible): Convert the defined area to its negative image.
Bright areas will be changed to dark ones and dark areas
changed to bright ones. Colors will be changed to their
complementary ones.

MOSAIC: Mask the defined area with flickering mosaic.
COLOR: Mask the defined area with selected colors.
Press direction button to enter menu to define Privacy position

and size.

COLOR: Select the color of the area. There are 16 colors selectable.
It is only available when DISPLAY is set to COLOR.

TRANS.: Select the transparency of the privacy area between 0 and

3. It only works when DISPLAY is set to COLOR.
DEFAULT: Select to restore the settings back to default.

DEFECT In a CCD or CMOS image sensor, there may be some defective

pixels that could not capture the light correctly. Use this function to
correct defective pixels using the image signal processer.

LIVE DPC: Digital Pixel Correction.

It detects and corrects defective pixels during the camera
operating time.

16 TruVision HD-TVI 1080P Camera Configuration Manual

AUTO: Detect and repair defective pixels automatically.

STATIC DPC

1.START

2.LEVEL

---|------15

3

.SENS

-

UP x 20

4

.AGC ---|------2

5.RETURN RET

RS485

1. CAM ID

--------|255

2. ID DISPLAY ON�

3. BAUDRATE 2400

4. RETURN RET

ON: Repair defective pixels manually, configurable range [0-255],
select higher value to repair the defective pixels easily,

OFF: Disable DPC function.

STATIC DPC: Detect and correct defective pixels manually. Select
On/Off to enable/disable.

START: Start detecting and correcting defective pixels.
Press OK when you see the message on the screen.
LEVEL: The STATIC DPC level ranges from 0 to 60. The higher

the value, the easier it is to correct defective pixels.
Some defective pixels may not be identifiable for the system to

detect. In such a situation, adjust the SENS-UP to X2, X4, X6,
X8, X10, X15, X20, X25 or X30 to brighten defective pixels and
facilitate the system to find them. Set the AGC level from 0 to 8.

RS-485 Set the RS-485 parameters, including camera ID, ID display status

and baud rate (2400/4800/9600/19200/38400).

Note: Only the TVC-2401/4401camera has a RS-485 port and RS­485 menu.

HEATCTRL Heat control.

Select the heater mode as ON, OFF or AUTO.

OFF: Heater is disabled.
AUTO: The heater starts to work when the temperature falls

below -10 °C. When temperature increases to -5 °C, it will stop
working.

ON: The heater starts to work when temperature falls below

-40°C. When the temperature increases above -40 °C, the heater
will stop working.

Note: Only the TVB-2406/4406 camera has this function.

Adjust

Use this menu to configure sharpness, monit or settings, OSD settings, lens
shadow compensation, as well as to change the video output standard, etc.
Move the cursor to ADJUST and press OK to enter the menu.

Select the following options under the Adjust menu:

TruVision HD-TVI 1080P Camera Configuration Manual 17

CRT

1. BLACK LEVEL ----|----+0

2. BLUE GAIN ----|----50

3. RED GAIN ----|----60

4.RETURN RET

LCD

1. GAMMA AUTO
2

. BLUE GAIN

----|----

50

3.

RED GAIN ----

|----50

4.RETURN RET

SHARPNESS Adjust the value from 0 to 15. The higher the value, the clearer and

sharper the image appears.
MONITOR Select CRT or LCD.

CRT: Set the black level [-30 to +30], blue gain [-50 to +50], and red

gain [-50 to +50].

LCD: Set gamma, blue gain [0 to100], and red gain [0 to100].

Gamma is the name of a nonlinear operation used to code and

decode luminance or tristimulus values in video or a still image

system. The options are: USER +Y, USER, AUTO, 1.00, 0.95, 0.90,

0.85, 0.80, 0.75, 0.70, 0.65, 0.60, 0.55, 0.50, and 0.45 are selectable.

LSC Lens Shading Correction.

Corrects image shades at the corners of an image. Set ON/OFF to

enable/disable.
VIDEO OUT Select the video output, PAL or NTSC.

Reset

Reset all settings to back default.

Exit

Press OK to exit the menu.

18 TruVision HD-TVI 1080P Camera Configuration Manual