Interlogix TVB-5502, TVT-5501, TVT-5502, TVD-5501, TVD-5502 Installation Guide

TruVision

Series 5 IP

Camera Installation

Guide

P/N 1073339-EN • REV B • ISS 13SEP17

environment. This equipment generates, uses, and

interference to radio communications. Operation of

Trademarks and

Manufacturer Interlogix

Certifica tion

Trade names used in this document may be

patents

trademarks or registered trademarks of the manufacturers or vendors of the respective products.

2955 Red Hill Avenue, Costa Mesa, CA

92626-5923, USA

Authorized EU manufacturing representative: UTC Fire & Security B.V. Kelvinstraat 7, 6003 DH Weert, The Netherlands

FCC compliance

FCC conditions This device complies with Part 15 of the FCC

Class A: This equipment has been tested and

found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial

can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful

this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Rules. Operation is subject to the following two

conditions:

(1) This device may not cause harmful

local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection

marked with this symbol, which may include

interference.

(2) This Device must accept any interference received, including interference that may cause undesired operation.

ACMA compliance Notice! This is a Class A product. In a domestic

environment this product may cause radio interference in which case the user may be required to take adequate measures.

Canada This Class A digital apparatus complies with CAN

ICES-003 (A)/NMB-3 (A ).

Cet appareil numérique de la classe A est conforme à la norme CAN ICES-003 (A)/NMB-3 (A).

European Union

directives

This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized

European standards listed under the EMC Directive 2014/30/EU, the RoHS Directive

2011/65/EU.

2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your

points. For more information see: www.recyclethis.info.

2013/56/EU & 200 6/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is

Contact information

lettering to indicate cadmium (Cd), lead (Pb), or

mercury (Hg). For proper recycling, return the

battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info.

For contact information, see www.interlogix.com or www.utcfssecurityproducts.eu.

Content

Introduction 2

Product overview 2

Installation 3

Installation environment 3 Package contents 4 Cable requirements 10 Camera description 11 Setting up the camera 13 IR illuminators 13 Accessing the SD card 14

Mounting the bullet camera 14 Mounting the turret camera 15 Mounting the dome camera 18

Using the camera with a TruVision recorder or another

system 22

Using the camera with TruVision Navigator 22

Specifications 22

TruVision IP bullet cameras 22 TruVision IP turret dome 23 TruVision IP dome cameras 23

Pin definitions 24

Installation Guide 1

Introduction

Product overview

This is the installation guide for TruVision Series 5 IP camera models:

 TVB-5501 (3MPX IP bullet camera)

 TVB-5502 (8MPX IP bullet camera)

 TVT-5501 (3MPX IP turret camera)

 TVT-5502 (8MPX IP turret camera)

 TVD-5501 (3MPX IP dome camera)

 TVD-5502 (8MPX IP dome camera)

2 Installation Guide

Installation

This section provides information on how to install the cameras.

Installation environment

When installing your product, consider these factors:

• Electrical: Install electrical wiring carefully. It should be

done by qualified service personnel. Always use a proper PoE switch or a 12 VDC UL listed Class 2 or CE certified power supply to power the camera. Do not overl oad the power cord or adapter.

• Ventilation: Ensure that the location planned for the installation of the camera is well ventilated.

• Temperature: Do not operate the camera beyond the specified temperature, humidity or power source ratings. The operating temperature of the camera wi thout heater is between -30 to +60°C (-22 to 140°F). Humidity is below 90%. For the outdoor cameras that feature built-in heaters, the operati ng temperature range is -40 to 60°C (-40 to140°F)

• Moisture: Do not expose the camera to rain or moisture or try to operate it in wet areas. Turn the power off immediately if the camera is wet and ask a qualified

service person for servicing. Moisture can damage the

camera and also create the danger of electri c shock.

• Servicing: Do not attempt to service this camera yourself. Any attempt to dismantle or remove the covers from this product will invalidate the warranty and may also result in serious injury. Refer all servicing to qualified service personnel.

Installation Guide 3

• Cleaning: Do not touch the sensor modules with fingers.

Hole

Ceiling Mounting

If cleaning is necessary, use a clean cloth with some ethanol and wipe the camera gently. If the camera will not be used for an extended period of time, put on the lens cap to protect the sensors from dirt.

Package contents

Check the package and contents for visible damage. If any components are damaged or missing, do not attempt to use the unit; contact the supplier immediately. If the unit is returned, it must be shipped back in its original packaging.

IP bullet camera

• Camera

• 12 VDC connector:

Two terminal connector with positive and negative indicators.

• Water joint: Provides water resistance to

• Drill template

network cable connector.

4 Installation Guide

• Screws

Drywall anchor

7.5 × 24.5 mm (3 pcs)

Screw

M4 × 25 mm (3 pcs)

• Installation manual

• CD with Configuration

manual and TruVision Device Manager

• Equipment Disposal Sheet

• Battery Disposal Sheet • Torx wrench

Installation Guide 5

IP turret camera

• Camera

• Camera drill template • Water joint: Provides

• 12 VDC connector:

Two terminal connector with positive and negative indicators.

water resistance to network cable connector.

• Screws

Drywall anchor

7.5 × 24.5 mm (4 pcs)

• Adapter plate

Screw

M4 × 25 mm (4 pcs)

6 Installation Guide

+ 22 hidden pages