Interlogix TVB-5301, TVB-5304, TVB-5303, TVB-5306, TVD-5301 Configuration Manual

...

TruVision Series 3 IP Camera FW3.1 Configuration Manual

P/N 1073187-EN • REV D • ISS 29SEP17

2017 United Technologies Corporation.

Interlogix is part of UTC

Climate, Controls & Security, a unit of

United Technologies Corporation.

Trademarks and

patents

rade names used in this document may be trademarks or

registered trademarks of the manufacturers or vendors of the respective products.

Manufacturer

Interlogix

2955 Red Hill Avenue, Costa Mesa, CA 92626

-5923, USA

Authorized EU manufacturing representative: UT

C Fire & Security B.V.

Kelvinstraat 7, 6003 DH Weert, The Netherlands

Contact information

For contact information

, see www.utcfireandsecurity.com or

www.firesecurityproducts.com

TruVision Series 3 IP Camera FW3.1 Configuration Manual 1

Content

Introduction 3 Network access 5

Checking your web browser security level 5 Activating the camera 7 Overview of the camera web browser 9

Camera configuration 11

Configuration menu ov erview 11 Local configuration 12 System time 13 Network settings 15 Recording parameters 26 Video image 29 OSD (On Screen Display) 33 Overlay text 34 Privacy masks 35 Motion detection alarms 36 Tamper-proof alarms 40 Exception alarms 40 Alarm inputs and outputs 42

Cross line detection 44 Intrusion detection 46

Snapshot parameters 47 NAS settings 49 Storage devices 50 Recording schedule 50

Camera management 54

User management 54 RTSP authentication 56 IP address filter 57 Restore default settings 58 Import/export a configuration file 59 Upgrade firmware 59 Reboot camera 60

Camera operation 61

Logging on and off 61 Live view mode 62 Playing back recorded video 62 Searching event logs 65

2 TruVision Series 3 IP Camera FW3.1 Configuration Manual

Operating PTZ control 67

Index 70

TruVision Series 3 IP Camera FW3.1 Configuration Manual 3

Introduction

This is the user manual for TruVision Series 3 IP camera models:

IP fixed lens bullet camera:

 TVB-5301 (2MPX Bullet, 4 mm lens)  TVB-5302 (4MPX Bullet, 4 mm lens)

IP VF lens bullet camera:

 TVB-5303 (2MPX Bullet, 2.8 to 12 mm VF lens)  TVB-5304 (4MPX Bullet, 2.8 to 12 mm VF lens)

IP motorized lens bullet camera:

 TVB-5305 (2MPX Bullet, 2.8-12 mm VF motorized lens)  TVB-5306 (4MPX Bullet, 2.8-12 mm VF motorized lens)

IP fixed lens dome camera:

 TVD-5301 (2MPX Plastic Dome, 2.8 mm lens)  TVD-5302 (4MPX Plastic Dome, 2.8 mm lens)

IP VF lens dome camera:

 TVD-5303 (2MPX VF Dome)  TVD-5304 (4MPX VF Dome)

IP motorized lens dome camera:

 TVD-5305 (2MPX Dome, 2.8-12 mm VF Motorized lens)  TVD-5306 (4MPX Dome, 2.8-12 mm VF Motorized lens)

IP wedge camera:

 TVW-5301 (2MPX Wedge, 2.0 mm lens, Gray)  TVW-5302 (2MPX Wedge, 2.8 mm lens, Gray)  TVW-5303 (2MPX Wedge, 2.8 m m lens, White)  TVW-5304 (2MPX Wedge, 2.8 m m lens, Bl ac k )  TVW-5305 (4MPX Wedge, 2.8 mm lens, Gray)

IP turret camera:

 TVT-5301 (2MPX Turret, 2.8 mm lens, Gray)  TVT-5302 (2MPX Turret, 2.8 mm lens, White)  TVT-5303 (2MPX Turret, 2.8 mm lens, Black)  TVT-5304 (4MPX Turret, 2.8 mm lens, Gray)

4 TruVision Series 3 IP Camera FW3.1 Configuration Manual

 TVT-5305 (4MPX Turret, 2.8 mm lens, White)  TVT-5306 (4MPX Turret, 2.8 mm lens, Black)  TVT-5307 (4MPX Turret, 4.0 mm lens, White)

TruVision Series 3 IP Camera FW3.1 Configuration Manual 5

Network access

This manual explains how to configure the camera over the network with a web browser.

TruVision IP cameras can be configured and controlled using Microsoft Internet Explorer (IE) and other browsers. The procedures described use Microsoft Internet Explorer (IE) web browser.

Checking your web browser security level

When using the web browser interface, you can install ActiveX controls to connect and view video using Internet Explorer. However, you cannot download data, such as video and images due to the increased security measure. Consequently you should check the security level of your PC so that you are able to interact with the cameras over the web and, if necessary, modify the Active X settings.

Configuring IE ActiveX controls

You should confirm the ActiveX settings of your web browser.

To change the web browser’s security level:

1. In Internet Explorer, click Internet Options on the Tools menu.

2. On the Security tab, click the zone to which you want to assign a web site under “Select a web content zone to specify its security settings”.

3. Click Custom Level.

4. Change the ActiveX controls and plug-ins options that are signed or marked as safe to Enable. Change the ActiveX controls and plug-ins options that are unsigned to Prompt or Disable. Click OK.

- Or -

6 TruVision Series 3 IP Camera FW3.1 Configuration Manual

Under Reset Custom Settings, click the security level for the whole zone in the Reset To box, and select Medium. Click Reset.

Then click OK to the Internet Options Security tab window.

5. Click Apply in the Internet Options Security tab window.

Windows users

Internet Explorer for Windows operating systems have increased security measures to protect your PC from any malicious software being installed.

To have complete functionality of the web browser interface with Windows, do the following:

• Run the Browser interface as an administrator in your workstation

• Add the camera’s IP address to your browser’s list of trusted sites

To add the camera’s IP address to Internet Explorer’s list of trusted sites:

1. Open Internet Explorer.

2. Click Tools, and then Internet Options.

3. Click th e Security tab, and then select the Trusted sites icon.

4. Click th e Sites button.

5. Clear the “Require server verification (https:) for all sites in this zone” box.

6. Enter the IP address in the “Add this website to the zone” field.

7. Click Add, and then click Close.

8. Click OK in the Internet Options dialog window.

9. Connect to the camera for full browser functionality.

TruVision Series 3 IP Camera FW3.1 Configuration Manual 7

Activating the camera

When you fi r st start up the camera, the Activation window appears. You must define a high-security admin password before you can access the camera. There is no default password provided.

You can activate a password via a web browser and via TruVision Device Manager (included on the CD to find the IP address of the camera).

To activate the camera via the web browser:

1. Power on the camera and connect the camera to the network.

2. Input the IP address into the address bar of the web browser, and click Enter to enter the activation interface.

Notes:

 The default IP address of the camera is 192.168.1.70.  For the camera to enable DHCP by default, you must activate the camera

via TruVision Device Manager. Please refer to the following section, “To activate the camera via TruVision Device Manager” below.

3. Enter the password in the password field. Note: A valid password range must be between 8 and 16 characters. You can

use a combination of numbers, lower and upper case letters, and special characters : _ - , . * & @ / $ ? Space. The password must contain characters from at least two of these groups. We also recommend that you reset your password regularly. For high security systems, it is particularly recommended to reset the password monthly or weekly for better protection.

4. Confirm the password.

5. Click OK to save the password and enter the live view interface.

To activate the camera via TruVision Device Manager:

1. Run the TruVision Device Manager to search for online devices.

2. Check the device status from the device list, and select the inactive device.

8 TruVision Series 3 IP Camera FW3.1 Configuration Manual

3. Enter the password in the password field, and confirm it. Note: A valid password range must be between 8 and 16 characters. You can

4. Click OK to save the password. A pop-up window confirms activation. If activation f ail s , confirm that the

password meets the requirement and try again.

5. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking the checkbox of Enable DHCP.

6. Input the password and click the Save button to activate your IP address modification.

TruVision Series 3 IP Camera FW3.1 Configuration Manual 9

Overview of the camera web browser

The camera web browser lets you view, record, and play back recorded videos as well as manage the camera from any PC with Internet access. The browser’s easy-to-use controls give you quick access to all camera functions. See Figure 1 below.

If there is more than one camera connected over the network, open a separate web browser window for each individual camera.

Figure 1: Web browser interface – Live view

Table 1: Overview of the web browser interface

Name Description

1. Live view Click to view live video.

2. Playback Click to play back video.

3. Log Click to search for event logs. There are three main types: Alarm, Exception and Operation.

4. Configuration Click to display the configuration window for setting up the camera.

5. PTZ controls Zoom and focus options are available for motorized lens cameras.

6. Current user Displays current user logged on.

7. Logout Click to log out from the system. This can be done at any tim e.

10 TruVision Series 3 IP Camera FW3.1 Configuration Manual

Name

Description

8. Aspect ratio Select the aspect.

9. Streaming Switch between main stream and substream.

10. Viewer View live video. Time, date and camera name are displayed here.

11. Start/stop live view Click to start/stop live view.

12. Audio Adjust volume.

13. Manual Alarm Click to trigger the alarm output.

14. Bidirectional audio Turn on/off microphone.

15. Capture Click to take a snapshot of the video. The snapshot will be saved to the default folder in JPEG format.

16. Start/stop recording Click to record live video.

17. Digital zoom Click to enable digital zoom.

TruVision Series 3 IP Camera FW3.1 Configuration Manual 11

Camera configuration

This chapter explains how to configure the cameras through a web browser. Once the camera hardware has been installed, configure the camera’s settings

through the web browser. You must have administrator rights in order to configure the cameras over the internet.

The camera web browser lets you configure the camera remotely using your PC. Web browser options may vary depending on camera model.

There are two main folders in the configuration panel:

 Local configuration  Configuration

Configuration menu overview

Use the Configuration panel to configure the server, network, camera, alarms, users, transactions and other parameters such as upgrading the firmware. See Figure 2 and Table 2 below for descriptions of the configuration folders available.

Figure 2: Configuration panel (Device Information tab selected)

Table 2: Overview of the Configuration panel

Configuration folders Description

1. System Defines the camera name and number. Displays basic information on the device including SN and the current firmware version

, time settings,

maintenance, and serial port parameters. See “System time” on page 13, “Restore default settings” on page 58, and “Upgrade firmware” on page 59 for more information.

12 TruVision Series 3 IP Camera FW3.1 Configuration Manual

Configuration folders Description

Network

Defines the network parameters required to access the camera over

the internet. See “Network settings” on page 15 for more information.

Video/Audio

Defines recording parameters. See “Recording parameters” on page

26 for more information.

Image

Defines the image parameters, OSD settings, overlay text, and privacy

mask. See “Video image” on page 29, “OSD (On Screen Display)” on page 33, “Overlay text” on page 34, and “Privacy masks” on page 35 for more information.

Security

Defines who can use the camera, their passwords and access

privileges, RTSP authentication, IP address filter, and SSH access. See “Camera management” on page 54 for more information.

Basic

Events Defines motion detection, tamper-proof, alarm input/output, and

exception. See “Motion detection alarms” on page 36, “Tamper-proof alarms” on page 40, and “Exception alarms” on page 40.

Smart Event

Defines cross line and intrusion detection.

Storage

Defines recording schedule, storage management, NAS configuration,

and Snapshot parameters. See “NAS settings” on page 49, “Storage devices” on page 50, and “Recording schedule” on page 50 for more information, and “Snapshot parameters” on page 47 for more information.

Local configuration

Use the Local menu to manage the protocol type, live view performance and local storage paths. In the Configuration panel, click Local Configuration to display the local configuration window. See Figure 3 and Table 3 below for descriptions of the differ ent me nu par a met ers.

Figure 3: Example of a configuration window (Local configuration shown)

TruVision Series 3 IP Camera FW3.1 Configuration Manual 13

Table 3: Overview of the Local configuration window

Parameters Description Live View Parameters

Protocol

Specifies the network protocol used.

Options include: TCP, UDP, MULTICAST and HTTP.

Live View Perfor

mance Specifies the transmission speed.

Options include: Shortest Delay or Auto.

Rules

It refers to the rules on your local browser. Specify whether or

not to display the colored marks when motion detection, face detection, and intrusion detection are triggered. For example, when the rules option is enabled and a face is detected, the

face will be marked with a green rectangle in live view.

Image Format

Choose the image format for a snapshot: JPEG or BMP.

Record File Settings

Record F

ile Size Specifies the maximum file size.

Options include: 256 MB, 512 MB and 1G.

Save

Record Files to Specifies the directory for recorded files.

Save

Downloaded Files to Specifies the directory for downloaded files.

Snapshot and Clip Settings

Save

Snapshots In Live View

Specifies the directory for saving snapshots in live view mode.

Save

Snapshots When

Playback To

Specifies the directory for saving snapshots in playback mode.

10.

Save Clips To

Specifies the directory for saving video clips in playback mode.

System time

NTP (Network Time Protocol) is a protocol for synchronizing the clocks of network devices, such as IP cameras and computers. Connecting network devices to a dedicated NTP time server ensures that they are all synchronized.

To define the system time and date:

1. Click Configuration > System > Time Settings.

14 TruVision Series 3 IP Camera FW3.1 Configuration Manual

2. From the Time Zone drop-down menu select the time zone that is the closest to the camera’s location.

3. Under Time Sync, check one of the options for setting the time and date: Synchronize with an NTP server: Check the NTP enable box and enter the

server NTP address. The time interval can be set from 1 to 1 0080 minutes.

- Or Set manually: Enabl e the Manual Time Sync. function and then click to

set the system time from the pop-up calendar. Note: You can also check the Sync with computer time check box to

synchronize the time of the camera with the time of your computer.

4. Check Enable DST to enable the DST function, and set the date of the DST period.

5. Click Save to save changes.

TruVision Series 3 IP Camera FW3.1 Configuration Manual 15

Network settings

Accessing the camera through a network requires that you define certain network settings. Use the “Network” folder to define the network settings. See Figure 4 and Table 4 below for fur ther in for ma ti on.

Figure 4: Network window (TCP/IP tab shown)

Table 4: Network parameters

Parameters Description

TCP/IP

NIC Type: Specifies the NIC type. Default is Auto. Other options include:

10M Half-dup, 10M Full-dup, 100M Half-dup and 100M Full-dup. DHCP: Enable to automatically obtain an IP address and other network

settings from that server.

IPv4 Address: Specifies the IPv4 address of the camera. IPv4 Subnet Mask: Specifies the IPv4 subnet mask. IPv4 Default Gateway: Specifies the IPv4 gateway IP address. IPv6 Mode: Specifies the IPv6 mode, including Manual, DHCP and Router

Advertisement. IPv6 Address: Specifies the IPv6 address of the camera. IPv6 Subnet Prefix Length: Specifies the IPv6 prefix length. IPv6 Default Gateway: Specifies the IPv6 gateway IP address. Mac Address: Specifies the mac address of the camera. MTU: Specifies the valid value range of MTU. Default is 1500. Multicast Address: Specifies a D-class IP address between 224.0.0.0 to

239.255.255.255. Only specify this option if you are using the multicast

function. Some routers prohibit the use of multicast function in case of a

16 TruVision Series 3 IP Camera FW3.1 Configuration Manual

Parameters Description

network storm.

Enable Multicast Discovery: Enables the automatic detection of the online network camera via private multicast protocol in the LAN.

DNS server: Specifies the preferred and alternate DNS server for your network.

Port

HTTP Port: The HTTP port is used for remote internet browser access.

Enter the port used for the Internet Explorer (IE) browser. Default value is

80. RTSP Port: RTSP (Real Time Streaming Protocol) is a network control protocol designed for use in entertainment and communications systems to control streaming media servers. Enter the RTSP port value. The default port number is 554.

HTTPS Port: HTTPS (Hyper Text Transfer Protocol Secure) allows video to be securely viewed when using a browser. Enter the HTTPS port, value. The default port number is 443.

Server Port: This is used for remote client software access. Enter the server port value. The default port number is 8000.

Alarm Server IP: Specifies the IP address of the alarm host. Alarm Server Port: Specifies the port of the alarm host.

DDNS

DDNS is a service that maps Internet domain names to IP addresses. It is

designed to support dynamic IP addresses, such as those assigned by a DHCP server.

Specifies DynDNS, and ezDDNS. DynDNS (Dynamic DNS): Enter the user name and password registered to

the DynDNS web site. The domain name is that of the DynDNS web site. ezDDNS: Enter the host name. It will automatically register it online.

PPPoE

Retrieves a dynamic IP address.

SNMP

SNMP is a protocol for managing devices on networks. Enable SNMP to get

camera status and parameter related information.

802.1X

When the feature is enabled, the camera data is secured and user

authentication is needed when connecting the camera to the network. See page 15 for setup information.

QoS

QoS (Quality of Service) can help solve the network delay and network

congestion by configuring the priority of data sending. Enable the option in order to solve network delay and network congestion by

configuring the priority of data sending.

FTP

Enter the FTP address and folder to which snapshots of the camera can be

uploaded.

UPnP

The UPnP (Universal Plug and Play) protocol allows devices to connect

seamlessly and to simplify the implementation of networks in the home and corporate environments. With the function enabled, you do not need to configure the port mapping for each port, and the camera is connected to the Wide Area Network (WAN) via the router.

Enable and set the friendly name detected.

Specifies the email address to which messages are sent when an alarm

occurs.

TruVision Series 3 IP Camera FW3.1 Configuration Manual 17

Parameters Description

NAT

The UPnP (Universal Plug and Play) protocol allows devices to connect

Enable and set the friendly name detected.

HTTPS

Specifies authentication of the web site and its associated web server, which

protects against Man-in-the-middle attacks .

To define the TCP/IP parameters:

1. Click Configuration > Network > TCP/IP.

2. Configure the NIC settings, including the NIC Type, IPv4 settings, IPv6 settings, MTU settings, and Multicast Address.

3. If the DHCP server is available, check DHCP.

4. If the DNS server settings are required for some applications (e.g., sending email), you should configure the Preferred DNS Server or Alternate DNS

Server.

5. Click Save to save changes.

To define the port parameters:

1. Click Configuration > Network > Port.

18 TruVision Series 3 IP Camera FW3.1 Configuration Manual

2. Set the HTTP port, RTSP port, HTTPS port, and server port o f the c amera. HTTP Port: The default port number is 80. It can be changed to any port

number that is not occupied. RTSP Port: The default port number is 554. It can be changed to any port

number in the range from 1 to 65535. HTTPS Port: The default port number is 443. It can be changed to any port

number that is not occupied. Server Port: The default server port number is 8000. It can be changed to

any port number in the range from 2000 to 65535.

3. Enter the IP address and port if you want to upload the alarm information to the remote alarm host. Also check the Notify Alarm Recipient option in the normal Linkage of each event pag e.

4. Click Save to save changes.

To define the DDNS parameters:

1. Click Configuration > Network > DDNS.

2. Check Enable DDNS to enable this feature.

3. Select the DDNS Type. Select one of the follow options:

TruVision Series 3 IP Camera FW3.1 Configuration Manual 19

• DynDNS: Enter the DNSS server address, members.ddns.org, which is used to notify DDNS about changes to your IP address, the host name for your camera, the port number (443 (HTTPS)), and your user name and password used to log into your DDNS account. The domain name displayed under “Host Name” is that which you created on the DynDNS web site.

• ezDDNS: Enter the desired host name under “Host Name”. The default host name is utc-serial number. The new host name is registered when you click Save.

Note: The default server address is www.tvr-ddns.net, which cannot be changed.

4. Click Save to save changes.

5. If you selected ezDDNS and changed the host name, click the Get URL button to confirm the domain name, which is displayed under Effect Dom ai n.

To define the PPPoE parameters:

1. Click Configuration > Network > PPPoE.

2. Check Enable PPPoE to enable this feature.

3. Enter User Name, Password, and Confirm password for PPPoE access.

4. Click Save to save changes.

20 TruVision Series 3 IP Camera FW3.1 Configuration Manual

To define the SNMP parameters:

1. Click Configuration > Network > SNMP.

2. Select the corresponding version of SNMP: v1, v2c, v3, or “Other Settings”.

3. Configure the SNMP settings. The configuration of the SNMP software should be the same as the settings you configure here.

4. Click Save to save changes.

Note: Before setting the SNMP, please download the SNMP software and ensure that you can receive the camera information via the SNMP port. By setting the Trap Address, the camera can send the alarm event and exception messages to the surveillance center. The SNMP version you select should be the same as that of the SNMP software.

TruVision Series 3 IP Camera FW3.1 Configuration Manual 21

To define the 802.1X parameters:

1. Click Configuration > Network > 802.1X.

Check Enable IEEE 802.1X to enable the feature. Configure the 802.1X settings, including EAPOL version, user name, and

password. The EAPOL version must be identical with that of the router or the switch.

Click Save to save changes.

To define the QoS parameters:

1. Click Configuration > Network > QoS.

2. Configure the QoS settings, including Video / Audio DSCP, Ev ent / Alarm DSCP, and Management DSCP. The valid value range of the DSCP is 0 to

63. The larger the DSCP value, the higher the priority.

3. Click Save to save changes.

+ 51 hidden pages

Interlogix TVB-5301, TVB-5304, TVB-5303, TVB-5306, TVD-5301 Configuration Manual

Specifications and Main Features

Frequently Asked Questions

User Manual