Interlogix TVB-4401 Installation Guide

TruVision High Definition TVI
Bullet Camera Installation
Guide

TVB
TVB-2403, TVB-4403

P/N 1072936-EN • REV A • ISS 12MAR15

-2401, TVB-4401

Contents

Product overview 1
Camera description 3
Installation 5
Programming 7

Setup menu 9
Specifications 10

Legal and regulatory information 11

Product overview

This is the Installation Guide for TruVision High
Definition TVI Bullet Camera TVB-2401/TVB-4401 and
TVB-2403/TVB-4403. This guide describes a standard
installation.

Installation Guide 1

Package contents:

 Camera with power

and video output
cables

 3 screws and 3

anchors for wall or
ceiling installation

 Template

• WEEE and Battery
Disposal

2 Installation Guide

 Installation Guide

 CD

Camera description

output

5

6

4

2

1

3

TVB-2401/TVB-4401

1. TVI video output
cable (grey)

2. Power cable

3. Mounting base

Installation Guide 3

4. Sun shield

5. Lens

6. IR LED

TVB-2403/TVB-4403

cable (black)

7

8

6

2

1

3
4

5

1. WDR/CVBS switch
cable

2. Power cable

3. TVI video output
cable (gre y)

5. Mounting base

6. Sun shield

7. Lens

8. IR LED

4. CVBS video output

Note:

Please check the camera output settings before setting
up a system. The TVI video output can be only

connected to a DVR with TVI signal input. The CVBS

output supports the standard monitor, test monitor,
encoder and DVR.

4 Installation Guide

For TVB-2403/TVB-4403, you can connect the white

Drill Template

and black line ends of the WDR switch cable to enable
the Wide Dynamic Range (WDR) function. The WDR
function is disabled by default. If W DR is enabled, the
CVBS output will be blocked out, and only TVI output

is available.

Installation

To install the camera on a ceiling:

1. Using the template, place it level against the
mounting surface and mark the position of the
mounting holes.

2. Following all local codes, drill and prepare the
mounting holes.

3. Securely fasten the mount to the mounting
surface with the screws.

Installation Guide 5

360°

90°

360°

4. Using a 75-ohm coaxial video cable, connect the
camera TVI video output and a TVI DVR, and
connect a 12 VDC power supply to the camera
power cable.

5. Adjust the camera position and angle as required.

6 Installation Guide

Programming

TVI

Programming on TVI output:

Programming on TV I output is available for TVB­2403/TVB-4403 only.

Once the camera hardware has been installed, you
can configure the camera settings on the TVI DVR.

Select PTZ protocol as TruVision Coax and click
menu button to call up the camera menu.

For more details, please see the TVI DVR user manual.

Installation Guide 7

Programming on CVBS output:

TVI

CVBS

Programming on CVBS output is available for TVB­2403/TVB-4403 only.

Programming on CVBS output, you need to connect a
monitor and a TVS-C200 controller (purchase

separately) as following system figure.

The TVS-C200 has one male BNC output and a
female output. Please connect the male output to
camera’s CVBS output and female output to a monitor.

8 Installation Guide

Setup menu

Installation Guide 9

Specifications

Power supply

12 VDC

Current

Max.300mA

Power
consumption

TVB-2401/TVB-4401:

Weight

Di
(Ø × L)

2.76 x 5.89 in. (70 x 149.5 mm)

TVB-2401/TVB-4401:

mensions

10 Installation Guide

TVB-2403/TVB-4403:
Max. 330mA

Max. 3.5 W
TVB-2403/TVB-4403:
Max.4 W

TVB-2401/TVB-4401: 0.64 lb.
(291 g)

TVB-2403/TVB-4403: 0.68 lb.
(309 g)

Legal and regulatory

information

Class A: This equipment has been tested and found to comply with

erated in a commercial environment. This equipment generates,

and used in accordance with the instruction manual, may cause

Copyright:

© 2015 United Technologies Corporation,

Interlogix is part of UTC Building & Industrial Systems, a unit of

United Technologies Corporation. All rights reserved.

Trademarks and patents:

Trade names used in this document may be trademarks or
registered trademarks of the manufacturers or vendors of the
respective products.

Manufacturer:

Interlogix
2955 Red Hill Avenue, Costa Mesa, CA 92626-5923, USA
Authorized EU manufacturing representative:

UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands

Certification:

N4131

FCC compliance: Class A

the limits for a Class A digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is
op
uses, and can radiate radio frequency energy and, if not installed

Installation Guide 11

harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the
interference at his own expense.

ACMA compliance

Notice! This is a Class A product. In a domestic environment this
product may cause radio interference in which case the user may
be required to take adequate measures.

Canada

This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme

NMB-0330 du Canada.

European Union directives:

12004/108/CE (EMC directive): Hereby, UT C Fire & Security declares

that this device is in compliance with the essential requirements and
other relevant provisions of Directiv e 2004/108/EC.

Contact information:

For contact information, see www.interlogix.com or
www.utcfssecurityproducts.eu

2012/19/EU (WEEE directi ve): Products marked
with this symbol cannot be disposed of as
unsorted municipal waste in the European Union.
For proper recycling, return this product t o your
local supplier upon the purchase of equiv alent new
equipment, or dispose of it at designated coll ection
points. For more inf ormation see:
www.recyclethis.info.

12 Installation Guide