Interlogix TVB-4105 User Manual
TruVision TVB-2104/4104
and TVB
-2105/4105 IR
Camera User Manual
P/N 1072698A-EN • REV 1.0 • ISS 10OCT13
Copyright
©
2013 UTC Fire & Security. All rights reserved.
Trademarks and
patents
The TruVision and Interlogix names and logo are t rademarks of
UTC
Other
registered trademarks of the manufacturers o r vendors of the
respective products.
Manufacturer
UTC Fire & Security Americas Corporation, Inc.
2955 Red Hill Avenue, Costa Mesa, CA 92626
Authorized EU manufacturing represent ative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherland s
Certification
FCC compliance
Class A:
the limits for a Class A digital
Rules. These limits are designed to provide reason able protection
against harmful interference when the equi pm ent is operated in a
commercial environment. This equipment generates, uses, and can
radiate radio frequen
accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful int erf erence in which
case the user wil
expense.
ACMA compliance
Notice!
product may cause radio interference in which case the user may be
required to take adequate measures.
European Union
directives
12004/108/EC (EMC directive):
declares that this device is in compliance or wit h the essential
requirements and other relevant provisions of Directive 2004/108/EC
2002/96/EC (WEEE directive):
cannot be disposed of as unsorted municipal waste in the European
Union. For proper recycling, return this product t o your local supplier
upon the purchase of equivalent new equipment , or dispose of it at
designated collection
www.recyclethis.info.
Contact information
For contact information
www.utcfssecurityproducts.eu
Fire & Security.
trade names used in this document may be trademarks or
-5923, USA
N4131
This equipment has been tested and found to comply with
device, pursuant to part 15 of the FCC
cy energy and, if not installed and used in
l be required to correct the interference at hi s own
This is a Class A product. In a domestic environm ent this
Hereby, UTC Fire & Security
Products marked with this symbol
points. For more information see:
, see www.utcfireandsecurity.com or
.
Content
Product overview 2
Package contents 2
Features 2
User guidelines 2
Product description 3
Installation 4
Mount the camera 4
Connect the cables 5
Adjust the focus and zoom 5
Programming 5
Access the Main menu 6
Exposure 7
Backlight 8
Day/Night mode 10
Image noise reduction 11
Defog 12
Function menus 13
Privacy mask area 14
Digital effect 15
Image adjustment 17
Protocol adjustment 18
Autofocus 20
OSD language 21
Exit menu 21
Specifications 21
Menu Tree 22
TruVision TVB-2104/4104 and TVB-2105/4105 IR Camera User Manual 1
Product overview
The TVB-2104/4104 and TVB-2105/4105 camera uses a digital signal processor
(DSP) to process video signals. The camera includes a microcontroller to provide
high-quality images with high-color reproduction and sharp pictures.
Package contents
The package contains the following:
• Camera
• Monitor output cable
• Mounting screws, wall anchors, and hex wrench
• Power terminal
• Ceiling drilling holes template
Note: Use the video output BNC and power jack for normal system operation.
Use the monitor output cable for installation and maintenance.
Features
The camera includes the following features:
• Exview HAD II (hole accumulated diode) technology with 480,000 pixels
NTSC (570,000 PAL)
• Use of LSI (large scale integration) digital processors to produce 700 lines of
horizontal resolution
• Motorized lens with auto and manual focus for easy installation
• Advanced OSD (onscreen display) control via DVR with Coaxial Con trol
feature
• Advanced privacy mask areas to protect privacy concerns
• Digital WDR (wide dynamic range)
• Long life and high reliability
• Isolated switching power 12 VDC and 24 VAC
User guidelines
• Program the camera settings as much as possible before mounting the
camera. Take appropriate safety precautions while completing programming
after installation.
• Always use a 12 VDC or 24 VAC UL listed Class 2 power supply to power the
camera.
2 TruVision TVB-2104/4104 and TVB-2105/4105 IR Camera User Manual
A; Sunshield; B. Hidden cable bracket
• Do not use the camera over the temperature range specifications: -30 to
+60°C (-22 to +122°F)
• If the light source where the camera is installed experiences rapid, widevariations in lighting, the camera may not operate as intended.
WARNING: To reduce the risk of fire or electronic shock, do not expose the
camera to rain or moisture and do not remove the cover or back.
Product description
The camera consists of the following:
• Camera with power and video output cables
• Sunshield
• Drilling-hole template
• One dual-power terminal block with its screw and anchor
• Four anchors and four screws for wall or ceiling installation
Refer to the following figures when performing the camera setup procedures.
Figure 1: Parts of the camera
Figure 2: Camera lens, IR LEDs, and light
A. LED IR light (total number of lights varies
by model)
TruVision TVB-2104/4104 and TVB-2105/4105 IR Camera User Manual 3
B. Lens
C. Light sensor
Figure 3: OSD control cable
A. OSD control pad; B. Power cable; C. Video cable
Table 1: OSD control pad functions
Pad directions Description
Up Zoom-in lens or move the cursor upward to select an i tem.
Down Zoom-out lens or move the cursor downward to select an item.
Right
Left
Enter
Adjust the lens focus to far or move the cursor to the right t o select
or adjust the options of the selected item.
Adjust the lens focus to near or move the cursor lef t to select or
adjust the options of the selected item.
Press the center of the control pad to display the Main menu. If the
selected item has its own menu, press the control pad to enter a
submenu. Press the control pad for 2 seconds to save all settings
and exit the Main menu.
Installation
Please check the package contents and make sure that the device in the
package is in good condition and all the assembly parts are included.
To install the camera you will need to prepare the mounting surface, mount the
camera, make cable connections, adjust the lens and then configure the camera
settings.
Note: Before installing, please ensure that the mounting surface is strong enough
to withstand three times the weight of the camera. If the mounting surface is not
strong enough, the camera may fall and cause serious damage.
Mount the camera
1. When installing the TVB-2104/TVB-4104 and TVB-2105/TVB4105 camera,
please use the attached mount
2. Using the mount as a template, place it level against the mounting surface
and mark the position of the mounting holes.
3. Following all local codes, drill and prepare the mounting holes.
4. Securely fasten the mount to the mounting surface with the appropriate
fasteners.
4 TruVision TVB-2104/4104 and TVB-2105/4105 IR Camera User Manual
Connect the cables
To connect the cables:
1. Connect a coaxial cable from the camera’s BNC connector to a CCTV
monitor or video recording device.
2. Connect the 12 VDC or 24 VAC power supply to the power jack of the
camera.
Caution: Check for polarity when using a 12 VDC power supply.
Note: Please check the specification table on page 21for the power
consumption of the camera. We suggest the use of a 2A power supply for the
camera.
Adjust the focus and zoom
Figure 4: Zoom and focus adjustment
A
or
To adjust the camera zoom and focus:
1. Use the OSD control pad (A) or the coaxial controller (B) to adjust the camera
zoom and focus. See Figure 4.
TELE (Up) – Zoom in the lens
WIDE (Down) – Zoom out the lens
FAR (Right) - Adjust the lens focus
NEAR (Left) - Adjust the lens focus
B
Programming
Once the camera hardware has been installed, the camera can then be
configured.
Before using the OSD to configure the camera, ensure that the camera focal
length and focus are correctly adjusted.
TruVision TVB-2104/4104 and TVB-2105/4105 IR Camera User Manual 5
Access the Main menu
The Main menu provides access to the camera configuration options. The onscreen display (OSD) is only available in multi languages, such as English,
Korean, Traditional Chinese, Simplified Chinese, Japanese, Russian, French,
Spanish, Italian, Portuguese, Dutch, German, Polish, Turkish, Hebrew, Arabic.
Program the camera by attaching a standard video monitor to the system.
Figure 5: The Main menu
Table 2: Main menu description
Menu item Description
Lens Defines the lens brightness and iris speed.
Exposure Defines the method of iris control.
Backlight Defines the highlight compensation (HLC) an d backlight compensation
(BLC) set up.
White bal Defines the white balance (WB) set up
Day&night Defines the day/night (D/N) set up
Smart 3DNR Defines the digital noise reduction set up
De-fog Defines the defog set up
Function Defines motion detection, privacy, digital ef fect, image adjustment,
autofocus, language and OSD color set up
Exit Exits the menu and returns to live mode. Saves changes made.
To access the Main menu:
1. Press the OSD control pad (Enter) or Coaxial Control Enter button to access
the Main menu and its submenus.
2. Push the pad up, down, left and right or Coaxial Control TELE, WIDE, NEAR,
and FAR button to move between menu options.
3. Press the OSD control pad Coaxial Control Enter button to select an option.
4. When in a sub menu, select Return to return to the previous menu.
5. To exit the Main menu, move the cursor to Exit at the bottom of the screen
and press Enter. All changes are saved.
6 TruVision TVB-2104/4104 and TVB-2105/4105 IR Camera User Manual
Loading...