Page 1
TruVision IR
Turret Camera
TVT
-2202/TVT-4202
Installation
Guide
P/N
1072921 • REV A • ISS 10FEB15
Page 2
Page 3
Installation Guide 1
Contents
Product overview 2
Camera description 3
Installation 4
Programming 6
Specifications 7
Setup menu 8
Regulatory information 9
Page 4
2 Installation Guide
Product overview
This is the TruVision IR Turret Camera Installation
Guide for models TVT-2202/TVT-4202. This guide
describes a standard installation.
Package contents:
Camera with power
and video output
cables
4 M4 screws (4 x
25 mm) and 4 dry
wall anchors (Ø7.5
x 24.5 mm) for wall
or ceiling
installation
Template
Hex wrench
Page 5
Installation Guide 3
• WEEE and Battery
Disposal
Installation Guide
CD
Camera description
1. Camera
2. Enclosure
3. Mounting base
4. Video cable
5. Power cable
6. Lock screw
7. Zoom and focus
Page 6
4 Installation Guide
Installation
To install the camera:
1. Using the template, place it level against the
mounting surface and mark the position of the
mounting holes.
2. Following all local codes, drill and prepare the
mounting holes.
3. Loosen the lock screw and release the clip
plate to release the camera from the mounting
base.
Page 7
Installation Guide 5
4. Fix the mounting base to the mounting surface.
5. Route the cables to the cable hole and connect
the corresponding cables.
Connect a 75 ohm coaxial video cable to the
video cable, and connect a 12 VDC power
supply to the power cable..
6. Adjust the camera according to the figure
below to get an optimum angle.
Clip Plate
0~360°
0~75°
0~360°
Page 8
6 Installation Guide
7. Secure the camera to the mounting base by
tightening the lock screw.
8. Use a screwdriver to adjust the ZOOM screw
and the FOCUS screw until you get the
optimum image.
Programming
Once the camera hardware has been installed, the
camera can then be configured by using a TVSC200 controller (purchase separately).
Clip
Plate
Page 9
Installation Guide 7
The Setup menu provides access to the camera
configuration options. See page 8 for an overview of
the menu. Please refer to the configuration manual
for further information on setting up the camera.
Program the camera by attaching a standard video
monitor to the system.
Specifications
Power supply
12 VDC
Current Max. 420 mA
Power
consumption
Max. 5W
Weight (net) 1.76 lb. (800 g)
Dimensions
Ø 5.28 × 4.88 × 3.48 in.
(Ø 134.2 × 123.9 × 88.1
mm)
Page 10
8 Installation Guide
Setup menu
Page 11
Installation Guide 9
Regulatory information
Copyright:
© 2015 United Technologies Corporation.
Interlogix is part of UTC Building & Industrial Systems, a unit of
United Technologies Corporation. All rights reserved.
Trademarks and patents:
Trade names used in this document may be trademarks or
registered trademarks of the manufacturers or vendors of the
respective products.
Manufacturer:
Interlogix
2955 Red Hill Avenue, Costa Mesa, CA 92626-5923, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
Certification:
N4131
FCC compliance: Class A
Class A: This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
op
erated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful
Page 12
10 Installation Guide
interference in which case the user will be required to correct the
interference at his own expense.
ACMA compliance
Notice! This is a Class A product. In a domestic environment this
product may cause radio interference in which case the user may
be required to take adequate measures.
Canada
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme
NMB-0330 du Canada.
European Union directives:
12004/108/CE (EMC directive): Hereby, UTC Fire & Security declares
that this device is in compliance with the essential requirements and
other relevant provisions of Directive 2004/108/EC.
2012/19/EU (WEEE directive): Products marked
with this symbol cannot be disposed of as
unsorted municipal waste in the European Union.
For proper recycling, return this product to your
local supplier upon the purchase of equivalent new
equipment, or dispose of it at designated collection
points. For more information see:
www.recyclethis.info.
Contact information:
For contact information, see www.interlogix.com or
www.utcfssecurityproducts.eu
Loading...