
TruVision IR Turret
Camera TVT
P/N 1072922A • REV A • ISS 10FEB15

Installation Guide 1
Contents
Package contents 2
Camera description 4
Installation 4
Specifications 8
Regulatory information 9

2 Installation Guide
Package contents
This is the TruVision IR Turret Camera Installation
Guide for models TVT-2201/4201. This guide
describes a standard installation.
The camera consists of the following:
Camera with power
and video output
cables
3 M4 screws (3 x
25 mm) and 3
drywall anchor
(Ø7.5 x 24.5 mm)
for wall or ceiling
installation
Template

4 Installation Guide
Camera description
1. Mounting base
2. Fixed ring
3. Lock screw
4. Enclosure
5. Camera
6. Video cable
Installation
To install the camera:
1. Using the template, place it level against the
mounting surface and mark the position of the
mounting holes.

Installation Guide 5
2. Following all local codes, drill and prepare the
mounting holes.
3. Loosen the lock screw on the mounting base to
release the turret camera.
4. Securely fasten the mounting base to the
mounting surface with the screws.

6 Installation Guide
5. Connect a 75-ohm coaxial video cable to the
video cable, and connect a 12 VDC power
supply to the power cable.
6. Secure the camera to the mounting base by
tightening the lock screw.

Installation Guide 7
7. Loosen the locked screw to adjust the
surveillance angle according to the figure below,
then tighten the locked screw.
0°~360°
0°
~
75°
0°
~
360°

8 Installation Guide
Specifications
Power supply 12 VDC
Current Max. 330 mA
Power
consumption
Max. 1.8 W (Max. 4 W with IR
cut filter on)
Weight 0.88 lb. (400 g)
Dimensions
(Ø × L)
2.76 x 5.89 in.
(89.6 x 59.1 mm)

Copyright:
© 2015 United Technologies Corporation.
Interlogix is part of UTC Building & Industrial Systems, a unit of
United Technologies Corporation. All rights reserved.
Trademarks and patents:
Trade names used in this document may be trademarks or
registered trademarks of the manufacturers or vendors of the
respective products.
Manufacturer:
Interlogix.
2955 Red Hill Avenue, Costa Mesa, CA 92626-5923, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
Certification:
FCC compliance: Class A
Class A: This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
op
erated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the

interference at his own expense.
ACMA compliance
Notice! This is a Class A product. In a domestic environment this
product may cause radio interference in which case the user may
be required to take adequate measures.
Canada
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme
NMB-0330 du Canada.
European Union directives:
12004/108/CE (EMC directive): Hereby, UTC Fire & Security declares
that this device is in compliance with the essential requirements and
other relevant provisions of Directive 2004/108/EC.
2002/96/CE (WEEE directive): Products marked
with this symbol cannot be disposed of as
unsorted municipal waste in the European Union.
For proper recycling, return this product to your
local supplier upon the purchase of equivalent
new equipment, or dispose of it at designated
collection points. For more information see:
www.recyclethis.info.
Contact information:
For contact information, see www.interlogix.com or
www.utcfssecurityproducts.eu.