Interlogix TruVision TVD-2402, TruVision TVD-4402, TruVision TVD-2404, TruVision TVD-2405, TruVision TVD-4404 Installation Manual

TruVision High

Definition TVI

Vandal Dome Installation

Guide

TVD

-2402/TVD-4402

TVD

-2404/TVD-4404

TVD-2405/TVD-4405

P/N 1073166-EN • REV B • ISS 26MAY17

Installation Guide 3

Content

Product overview 4
Camera description 6
Installation 9
Operating temperature range 14
Program 14

Setup menu 19
Specifications 21
Legal and Regulatory information 23

4 Installation Guide

Product overview

This is the Installation Guide for the TruVision High
Definition TVI dome TVD-2402/TVD-4402，TVD­2404/TVD-4404 and TVD-2405/TVD-4405. This
guide describes a standard installation.

Package contents

 Camera with power

and video output
cables

 4 screws and 4

anchors for wall or
ceiling installation

 Template

 3 screws to install

the camera to the
back box

Installation Guide 5

 Hex wrench

 Monitor output

cable

 Spare rubber

knockout

There is a rubber knockout
on the camera back box.
This is for future use.

 Installation Guide

 CD

• WEEE and Battery
Disposal sheets

6 Installation Guide

Camera description

TVD-2402/TVD4402:

1. Dome liner

2. Bubble

3. Lens

4. Power cable

5. CVBS video output
cable (black)

6. TVI video output
cable (grey)

7. Back box

8. Switch (Left =

WDR / Right =
CVBS)

9. Menu button

10. CVBS output port

Installation Guide 7

TVD-2404/4404 and TVD2405/4405:

1. Dome liner

2. Bubble

3. Lens

4. Power cable

5. CVBS video output
cable (black)

6. TVI video output
cable (grey)

7. Back box

8. Switch (Left =

WDR / Right =
CVBS)

9. Menu button

10. CVBS output port

8 Installation Guide

Note:

Please check the camera output settings

before setting up a system. The TVI video
output can be only connected to DVR with
TVI signal input. The CVBS output supports a
standard CVBS monitor (or test monitor), an
encoder or a DVR.

For 720P Dome cameras TVD-2402/TVD-

4202, the CVBS and TVI output can not be

used at the same time. Use the built-in switch
to select the camera video output.

For 1080P Dome cameras TVD-2404/TVD­4404 and TVD-2405/TVD-4405, use the built­in switch to enable/disable the WDR feature.
When the WDR feature is enabled, the CVBS
output will be blocked.

Installation Guide 9

Installation

To install the camera on a ceiling:

1. Using the template, place it level against the
mounting surface and mark the position of the
mounting holes.

2. Following all local safety regulations, drill and
prepare the mounting holes.

3. Remove the camera from its back box.

4. Loosen the three screws on the edge of the
bubble with the supplied hex wrench.

5. Remove the bubble and the dome liner.

10 Installation Guide

6. Secure the back box to the ceiling with the
supplied screws.

Note: Please remove the rubber knockout for
cable routing outside of the camera, when
required.

Installation Guide 11

7. Using a 75-ohm coaxial video cable, connect

the camera TVI video output to a TVI DVR, and
connect a 12 VDC or 24 VAC power supply to
the power cable.

8. Align the camera with the back box and tighten
the screws to fasten the camera to the back
box.

7. Adjust the surveillance angle:

1) View the camera image on a monitor.

12 Installation Guide

2) Rotate the camera block to adjust the pan
direction [0 to 355°].

3) Loosen the tilting lock screw.

4) Rotate the camera block to adjust the tilt
direction [0 to 90°].

5) Tighten the tilting lock screw.

6) Rotate the camera lens holder [0 to 355°]
to adjust the lens to the surveillance angle.

8. Zoom and focus adjustment

a) Manually adjust the zoom and focus of TVD-

2402/TVD-4402 and TVD-2404/TVD-4404.

1) View the camera image using the monitor.

~

~

~

Installation Guide 13

2) Loosen the zoom lever and move the
screw between T (Tele) and W (Wide) to
obtain the appropriate angle of view.

3) Tighten the zoom lock screw.

4) Loosen the focus lever and move the
screw between F (Far) and N (Near) to
obtain the optimum focus.

5) Tighten the focus lock screw.

Zoom

Focus

b) TVD-2405/TVD-4405 has a motorized lens.

Adjust its zoom and focus by using the zoom
and focus buttons on the PTZ panel of a
connected recorder.

14 Installation Guide

Operating temperature range

The operating temperature of the TVD-2402/4402
and TVD-2404/4404 cameras is -30 to +60 °C (-22
to +140 °F).

When the camera initially starts up, the heater will
start to work automatically when the temperature is

below -10 °C (14 °F). However, with continuous
operation the heater will not work until the internal
temperature drops below -30°C (-22 °F). It will then
be disabled when the temperature reaches -10 °C
(14 °F). The heater only works under 24 VAC.

Program

Once the camera hardware has been installed, you

can then program the camera.

The camera has a built-in OSD button and supports
UtC (Up-to-Coax) control over both CVBS and TVI
outputs.

Installation Guide 15

Using the camera buttons

Please press the Menu button to call up the OSD
menu and select an OSD item.

Press the button up/down to move the cursor up or
down to an OSD item.

Press the button left/right to move cursor left or right
to adjust the value of a selected OSD item.

Using a TVI output

Once the camera hardware has been installed, you
can configure the camera settings on the TVI DVR.

Connect the TVI cable to the DVR, as shown below.

16 Installation Guide

Access the PTZ menu of the connected DVR, set

the TruVision-Coax protocol and use the PTZ
control panel to configure the camera.

Click Iris+ to access to the camera OSD menu and
select an OSD item.

Click the directional buttons UP or DOWN to move

the cursor up or down to an OSD item.

Click the directional buttons LEFT or RIGHT to

move cursor left or right to adjust the value of a
selected OSD item.

Note: The TVD-2405/TVD-4405 camera has a

motorized lens. Use the ZOOM and FOCUS buttons
to adjust its zoom and focus.

For more details, refer to the TVI DVR user manual.

Using a CVBS output

A TVS-C200 (purchase separately) can be used to
program the camera over its CVBS output, not the
TVI video output.

Connect a monitor and the TVS-C200 controller (if
required) as shown below.

Installation Guide 17

Press the OK button of the TVS-C200 for a few

seconds until you see the OSD menu display on the

monitor. The OK button is also used to select an
OSD item.

Use the directional buttons to move the cursor and
change a value.

For more details, refer to the TVS-C200 user
manual.

TVD-2402/TVD-4402

The camera has CVBS and TVI dual video outputs.
Set the built-in switch to CVBS for viewing the

program on a standard monitor.

18 Installation Guide

The TVI signal is blocked until the camera
configuration is complete and the switch is reset to

TVI.

TVD-2404/TVD-4404 and TVD-2405/TVD-4405

The camera has the CVBS and TVI dual video
outputs. The built-in switch is for WDR/CVBS
selection. Set the built-in switch to CVBS to view the

setup menu on a standard monitor.

When the programing is finished, you can change
the switch setting to WDR to enable the WDR
feature. In such case, the CVBS output will be

disabled.

If the switch is set to CVBS, the WDR feature is
disabled and the camera has the both CVBS and

TVI output available.

Installation Guide 19

Setup menu

TVD-2402/TVD-4402:

20 Installation Guide

TVD-2404/TVD-4404, TVD-2405/TVD-4405:

Installation Guide 21

Specifications

Power supply

24 VAC/12 VDC

Current

TVD-2402/ TVD-4402:

12 VDC: 300 mA max.
24 VAC: 210 mA max.
TVD-2404/TVD-4404:
12 VDC: 375 mA max.
24 VAC: 270 mA max.
TVD-2405/TVD-4405:
12 VDC: 1 A max.
24 VAC: 500 mA max.

Power
consumption

TVD-2402/ TVD-4402:

12 VDC: 3.5W max.
24 VAC: 5 W max.
TVD-2404/TVD-4404:
12 VDC: 4.5 W max.
24 VAC: 6.5 W max.
TVD-2405/TVD-4405:
12 VDC: 12 W max.
24 VAC: 12 W max.

Weight (net)

641 g / 1.41 lb. (without back box)

932 g / 205 lb. (with back box)

22 Installation Guide

Dimensions

Ø145.3 x 124.2 mm
(Ø 5.72 x 4.89 in. )

Installation Guide 23

Legal and Regulatory

information

Copyright:

© 2017 United Technologies Corporation,

Interlogix is part of UTC Climate, Controls & Security, a unit of
United Technologies Corporation. All rights reserved.

Trademarks and patents:

Trade names used in this document may be trademarks or

registered trademarks of the manufacturers or vendors of the
respective products.

Manufacturer:

Interlogix

2955 Red Hill Avenue, Costa Mesa, CA 92626-5923, USA
Authorized EU manufacturing representative:

UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands

Certification:

FCC compliance: Class A

Class A: This equipment has been tested and found to comply with

the limits for a Class A digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is
op

erated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause

24 Installation Guide

harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the
interference at his own expense.

ACMA compliance

Notice! This is a Class A product. In a domestic environment this

product may cause radio interference in which case the user may

be required to take adequate measures.

Canada

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme
NMB-0330 du Canada.

European Union directives:

12004/108/CE (EMC directive): Hereby, UTC Fire & Security declares

that this device is in compliance with the essential requirements and
other relevant provisions of Directive 2004/108/EC.

2012/19/EU (WEEE directive): Products marked

with this symbol cannot be disposed of as

unsorted municipal waste in the European Union.

For proper recycling, return this product to your

local supplier upon the purchase of equivalent new
equipment, or dispose of it at designated collection
points. For more information see:

www.recyclethis.info.

Contact information:

For contact information, see www.interlogix.com or
www.utcfssecurityproducts.eu