Interlogix TruVision TVD-2401, TruVision TVD-4401, TruVision TVD-2403, TruVision TVD-4403 Installation Manual

TruVision High

Definition TVI

Dome Installation Guide

TVD

-2401/TVD-4401

TVD-2403/TVD-4403

P/N 1072939-EN • REV A • ISS 11MAR15

2 Installation Guide

Content

Product overview 3
Camera description 5
Installation 8
Programming 11
Menu 13

Specifications 14
Legal and Regulatory information 15

Installation Guide 3

Product overview

This is the Pocket Guide for TruVision High
Definition TVI dome TVD-2401/TVD-4401 and TVD­2403/TVD-4403. This guide describes a standard
installation.

Package contents:

 Camera with power

and video output
cables

 3 screws and 3

anchors for wall or
ceiling installation

 Template

 Installation Guide

4 Installation Guide

• WEEE and Battery
Disposal

 CD

Installation Guide 5

Camera description

TVD-2401/TVD-4401

1. Base

2.

IR LED

3.

Lens

4. Dome liner

5. Housing

6.

Power supply

7.

TVI Video output
cable (grey)

6 Installation Guide

TVD-2403/TVD-4403

1. Base

2.

IR LED

3.

Lens

4.

Dome liner

5.

Housing

6.

Power supply

7.

TVI video output
cable (grey)

8.

CVBS video output

cable (black)

Installation Guide 7

Note:

Please check the camera output settings

before setting up a system. The TVI video
output can be only connected to DVR with
TVI signal input. The CVBS output supports

the standard monitor, test monitor, encoder
and DVR.

For TVD-2403/TVD-4403, you can connect
the white and black line ends of the WDR
switch cable to enable the Wide Dynamic

Range function. The WDR function is
disabled by default. If WDR is enabled, the
CVBS output will be blocked out, and only

TVI output is available.

8 Installation Guide

Installation

To install the camera on a ceiling:

1. Using the template, place it level against the
mounting surface and mark the position of the
mounting holes.

2. Following all local codes, drill and prepare the
mounting holes.

3. Loosen the screws with wrech to remove the
housing.

Drill Template

Hole A: for cables routed through the ceiling
screw hole 1: for Mounting Base

1

1

1

A

Installation Guide 9

4. Securely fasten the mounting base to the
mounting surface with the screws.

5. Using a 75 ohm coaxial video cable, connect
the camera TVI video output and a TVI DVR,
and connect a 12 VDC power supply to the
camera power cable.

10 Installation Guide

6. Adjust the surveillance angle according to the
figure below.

7. Re-attach the housing to the base.

Installation Guide 11

Programming

Programming on TVI output:

Programming on TVI output is available for TVD­2403/TVD-4403 only.

Once the camera hardware has been installed, you
can configure the camera settings on the TVI DVR.

Please select PTZ protocol as TruVision Coax and
click menu button to call up the camera menu.

For more details, please see the TVI DVR user

manual.

TVI

12 Installation Guide

Programming on CVBS output:

Programming on CVBS output is available for TVD­2403/TVD-4403 only.

Programming on CVBS output, you need to connect
a monitor and a TVS-C200 controller (purchase
separately) as following system figure.

The TVS-C200 has one male BNC output and a

female output. Please connect the male output to
camera’s CVBS output and female output to a
monitor.

TVI

CVBS

Installation Guide 13

Menu

14 Installation Guide

Specifications

Power supply

12 VDC

Current

TVD-2401/TVD-4401:

Max. 300 mA
TVD-2403/TVD-4403:
Max.333 mA

Power
consumption

TVD-2401/TVD-4401:

Max. 3.5W
TVD-2403/TVD-4403:
Max. 4W

Weight

345 g (0.76 lb.)

Dimensions
(Ø × L)

111 x 82 mm (4.4 x 3.2 in. )

Installation Guide 15

Legal and Regulatory

information

Copyright:

© 2015 United Technologies Corporation,

Interlogix is part of UTC Building & Industrial Systems, a unit of

United Technologies Corporation. All rights reserved.

Trademarks and patents:

Trade names used in this document may be trademarks or

registered trademarks of the manufacturers or vendors of the
respective products.

Manufacturer:

Interlogix
2955 Red Hill Avenue, Costa Mesa, CA 92626-5923, USA

Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands

Certification:

N4131

FCC compliance: Class A

Class A: This equipment has been tested and found to comply with

the limits for a Class A digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is
op

erated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause

16 Installation Guide

harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the
interference at his own expense.

ACMA compliance

Notice! This is a Class A product. In a domestic environment this

product may cause radio interference in which case the user may

be required to take adequate measures.

Canada

This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme

NMB-0330 du Canada.

European Union directives:

12004/108/CE (EMC directive): Hereby, UTC Fire & Security declares

that this device is in compliance with the essential requirements and
other relevant provisions of Directive 2004/108/EC.

2012/19/EU (WEEE directive): Products marked

with this symbol cannot be disposed of as

unsorted municipal waste in the European Union.

For proper recycling, return this product to your

local supplier upon the purchase of equivalent new
equipment, or dispose of it at designated collection
points. For more information see:

www.recyclethis.info.

Contact information:

For contact information, see www.interlogix.com or
www.utcfssecurityproducts.eu