Interlogix S7717D-RST2, S717DR-RST1, S717DT-RST1 Specsheet
GE
Fiber Optic
Security
Overview
The S717D and S7717D digital current loop transmission system
provides superior noise-free transmission of the 20 mA standard,
suitable for use in many applications including those found in
communications and monitoring systems. A complete system
consists of transmitter and receiver operating over one or two single
mode or multimode fibers. The S717D model features multimode
operation, while the S7717D model operates over single mode fiber.
Accurate Data Transmission
Utilizing high-speed data conversion and digital transmission,
the system provides highly accurate data transmission. The units
can be configured as active or passive receivers and drivers.
Superior Diagnostics
The SMARTS™ diagnostic technology provides built-in diagnostic
LEDs for monitoring data and optical signal strength.
Data Transmitters and Receivers
Standard Features
• Two-way data transmission over one or two single
mode or multimode fibers
• 20 mA digital current loop
• Selectable active/passive receivers and drivers
• Asynchronous operating mode
• 18 dB optical budget
• SMARTS™ diagnostics
Two-Way
Digital Current
Loop
S717D and S7717D
GE
Security
U.S.
T (561) 998-6100
T 888-GE-SECURITY
888-(437-3287)
F 561 998 6224
Canada
T 519 376 2430
F 519 376 7258
Asia
T 852-2907-8108
F 852-2142-5063
Australia
T 61-3-9239-1200
F 61-3-9239-1299
Europe
T
32-2-719-9847
F
32-2-719-9846
Latin America
T 305-593-4301
F 305-593-4300
www.gesecurity.com
© 2005 General Electric Company
All Rights Reserved
Specifications
Data S717D (Multimode) S7717D (Single Mode)
Channels 1 duplex
Format 20 mA digital current loop
Baud Rate
Impedance
Operating Mode
Bit Error Rate <1.0E-9
Optical
Mode Multimode Single Mode
Optical Budget 18 dB 18 dB
Emitter
Operating Distance
Wavelength 850 nm and/or 1300 nm 1310 nm and/or 1550 nm
Gain Control
Transmitter Launch Power
Receiver Sensitivity
Electrical
Input Power 13.5 VDC regulated
Current Requirement 350 mA
Power Consumption 5 W
Power Factor 3
Protection Solid-state short circuit protection
Environmental
Operating Temperature -40 to 167 °F (-40 to 75 °C)
Maximum Humidity 95% relative, noncondensing
Mechanical
Dimensions, Rack Units 1 slot (1.0”)
Weight 0.6 lbs (0.27 kg)
Construction Aluminum
∗
∗∗
15 mi (25 km) 37 mi (60 km)
Optical Automatic Gain Control (OAGC)
-14 dBm minimum -14 dBm
-32 dBm minimum -32 dBm
20 kbps
<5 ohms
Asynchronous
LED or Laser
(depending on model)
(depending on model)
Related Diagram
Current Loop
In/Out
Transceiver
Optical Fiber
Transceiver
Current Loop
In/Out
Ordering Information
Use the Configurator below to select the options available for this product.
S717D
Product Type
TRTransmitter
Receiver
Omit for Transceiver
∗ Optical Budget based on 62.5 μm fiber, for 50/125 μm fiber subtract 3 dB.
∗∗ Operating distance is approximate and assumes best fiber. It will be affected by the type and number of splices in the fiber. Refer to update No. TB00-005, which can be found at www.gesecurity.com
As a company of innovation, GE Security reserves the right to change product specifications without notice. For the latest product specifications, visit GESecurity online at www.GESecurity.com or contact your GE Security sales representative.
S717D-2006-09-2
- RST
No. of Fibers
1
Fiber
2
Fibers
(Transceiver only)
imagination at work
imagination at work
Optical Wavelength
L
Add here only if ordering
High Order Wavelength
(2 Fiber Transceivers only)
S7717D
Receiver
Product TypeConnector Type
TFC
Transmitter FC Type
RST
Receiver ST Type
(Omit for Transceiver)
- R
No. of Fibers
12Fiber
Fibers
(Transceiver only)
Optical Wavelength
Add here only if ordering
L
High Order Wavelength
(2 Fiber Transceivers only)
Loading...