IFS MC355-1T/1S
Quick Installation Guide
P/N 1076516 • REV A • ISS 09FEB12
Copyright © 2012 UTC Fire & Security Company. All rights
r
reserved.
Trademarks and
patents
Interlogix, IFS MC355-1T/1S, the IFS Brand and
logo are trademarks of UTC Fire & Security.
Other trade names used in this document may be
trademarks or registered trademarks of the
manufacturers or vendors of the respective
products.
Manufacture
UTC Fire & Security Americas Corporation, Inc.
2955 Red Hill Avenue, Costa Mesa, CA
92626-5923, USA
EU Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, Netherlands
Version This document applies to IFS MC355-1T/1S
version 1.0.
Certification
N4131
FCC compliance Class A: This equipment has been tested and
found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference when the
equipment is operated in a commercial
environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not
installed and used in accordance with the
instruction manual, may cause harmful
interference to radio communications. Operation
of this equipment in a residential area is likely to
cause harmful interference in which case the user
will be required to correct the interference at his
own expense.
Canada This Class A digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la classe A est
conforme à la norme NMB-003 du Canada.
ACMA
compliance
Notice! This is a Class A product. In a domestic
environment this product may cause radio
interference in which case the user may be
required to take adequate measures.
European Union
directives
2004/108/EC (EMC directive): Hereby, UTC Fire
& Security declares that this device is in
compliance with the essential requirements and
other relevant provisions of Directive 2004/108/EC
2002/96/EC (WEEE directive): Products marked
with this symbol cannot be disposed of as
unsorted municipal waste in the European Union.
For proper recycling, return this product to your
local supplier upon the purchase of equivalent
new equipment, or dispose of it at designated
collection points. For more information see:
www.recyclethis.info.
Contact
information
www.utcfireandsecurity.co
www.interlogix.com
m or
Customer support www.interlogix.com/customer-support
Contents
Package Contents 1
Hardware & Software requirements 1
Wiring the Power Inputs 2
Web Management 3
Logging in to Media Converter 4
Hardware & Password Reset 6
Contacting Technical Support 7
IFS MC355
-1T/1S Quick Installation Guide i
Package Contents
Thank you for purchasing the IFS 10/100/1000-T to mini-GBIC
Industrial Managed Media Converter, MC355-1T/1S.
Open the package containing the MC355-1T/1S and carefully
unpack it. The box should contain the following items:
• MC355-1T/1S x1
• User’s Manual CD x1
• Quick Installation Guide x1
• Wall Mount Kit x 4
• DIN Rail Kit x 1
If any of the items in the package are damaged or missing,
please contact your distributor or IFS sales rep. If possible,
retain the original carton and packaging material in case of
need to return the product for repair/replacement.
Hardware & Software requirements
• Client workstations running Windows 98/ME, NT4.0,
2000/XP, Vista, MAC OS9 or later, Linux, UNIX or other
platform compatible with TCP/IP protocols
• Workstation installed with Ethernet NIC (Network Card)
• Ethernet Port connection
• Network cables - Use standard network (UTP) cables with
RJ45 connectors
• PC installed with WEB Browser and JAVA runtime
environment Plug-in
Note: We recommended using Internet Explore 6.0 or above
to access the MC355-1T/1S Industrial Managed Media
Converter.
IFS MC355
-1T/1S Quick Installation Guide 1
Wiring the Power Inputs
The 6-contact terminal block connector on the top panel of
Industrial Managed Media Converter is used for two DC
redundant power supply inputs. Please follow the steps below
to insert the power wires.
1. Insert the positive / negative DC power wires into the
contacts 1 and 2 for POWER 1, or 5 and 6 for POWER 2.
Figure 1 shows PWR1 and PWR2 of the Industrial
Managed Media Converter.
Figure 1: PWR1 & PWR2 of Industrial Managed Media Converter
V1- V1+ V2- V2+
2. Tighten the wire-clamp screws to prevent the wires from
disconnecting. Figure 2 shows PWR1 and PWR2 pin of the
terminal block.
2 IFS MC355-1T/1S Quick Installation Guide
Figure 2: PWR1 & PWR2 of Industrial Managed Media Converter
1 2 3 4 5 6
Power 1 Fault Power 2
－ ＋ － ＋
Note: The wire gauge for the terminal block should be in the
range between 12 ~ 24 AWG.
Web Management
The MC355-1T/1S has a built-in browser interface. The media
converter can be managed remotely by having a remote host
with a Web browser, such as Microsoft Internet Explorer,
Mozilla Firefox, Google Chrome or Apple Safari.
To be able to login to the media converter, the administrator
workstation should be set to the same IP range and subnet
mask. Default IP address for media convert is 192.168.0.100,
and the default subnet mask is 255.255.255.0. Therefore, the
administrator PC should be set to 192.168.0.x (where x is a
number between 1 and 254) and subnet mask should be set to
255.255.255.0.
IFS MC355-1T/1S Quick Installation Guide 3
Figure 3: IP Management Diagram
Logging in to Media Converter
1. Open the web browser and enter the default IP address
http://192.168.0.100 to the address bar.
2. Figure 4 illustrates the Web Login screen that will appear
next.
Figure 4: Web Login screen
3. Enter the username and password (default user name and
password is “admin”) in Web login screen (as illustrated in
Figure 5).
4 IFS MC355-1T/1S Quick Installation Guide
Figure 5: Main Web screen
After a successful login, the MC355-1T/1S media converter can
be managed through the available menu options. Please refer
to the user manual for more information on the web
management menu options.
Note: For security purposes, please change the default
password and keep record of the new one after the first login.
IFS MC355-1T/1S Quick Installation Guide 5
Hardware & Password Reset
To reset the IP address to the default IP Address of
“192.168.0.100” and reset the login password to default value
(default user name and password is admin). Press and hold
the hardware reset button on the front panel for about 10
seconds. After the device is rebooted, you can login the
management Web interface with the default IP address of
192.168.0.100 and default user name / password (admin).
Figure 6: Reset button
6
IFS MC355-1T/1S Quick Installation Guide
Contacting Technical Support
Contact technical support if you encounter any difficulties
during this installation. Please make sure you have the
requested diagnostic or log files ready before you contact us
by phone or go to www.interlogix.com/customer-support.
Technical Support
Europe, Middle East and Africa
W Select Contact Us at www.utcfssecurityproducts.eu
North America
T +1 855.286.8889
E techsupport@interlogix.com
Australia
E techsupport@interlogix.au
IFS MC355
-1T/1S Quick Installation Guide 7
Loading...