Interlogix MC201-1P-1FS User Manual

IFS MC201-1P/1FS
User Manual

P/N 1076525 • REV A • ISS 07FEB12

Copyright © 2012 UTC Fire & Security Company. All rights

r

reserved.

Trademarks and

patents

Interlogix, IFS MC201-1P/1FS, the IFS Brand and

logo are trademarks of UTC Fire & Security.

Other trade names used in this document may be
trademarks or registered trademarks of the
manufacturers or vendors of the respective
products.

Manufacture

UTC Fire & Security Americas Corporation, Inc.

2955 Red Hill Avenue, Costa Mesa, CA
92626-5923, USA

Version This document applies to IFS MC201-1P/1FS

version 1.0.

Certification

N4131

FCC compliance Class A: This equipment has been tested and

found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference when the
equipment is operated in a commercial
environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not
installed and used in accordance with the
instruction manual, may cause harmful
interference to radio communications. Operation
of this equipment in a residential area is likely to
cause harmful interference in which case the user
will be required to correct the interference at his
own expense.

ACMA

compliance

European Union

directives

Notice! This is a Class A product. In a domestic

environment this product may cause radio
interference in which case the user may be
required to take adequate measures.

2004/108/EC (EMC directive): Hereby, UTC Fire

& Security declares that this device is in
compliance with the essential requirements and
other relevant provisions of Directive 2004/108/EC

2002/96/EC (WEEE directive): Products marked

with this symbol cannot be disposed of as
unsorted municipal waste in the European Union.
For proper recycling, return this product to your
local supplier upon the purchase of equivalent
new equipment, or dispose of it at designated
collection points. For more information see:

www.recyclethis.info.

Contact

information

Customer support

www.utcfireandsecurity.com or
www.interlogix.com

www.interlogix.com/customer-support

Contents

Overview 1

About the MC201-1P/1FS 1

Package Contents 2
Hardware Overview 3

Front Panel 4
Back Panel 4

Link Fault Pass-through (LFP) 4
Link Loss Carry Forward (LLCF) 5
Link Loss Return (LLR) 6
Installing the Converter 7
PoE Function 8
LED Indicators 9

System 9
10/100Base-TX Port 9
100Base-FX SC Port 9

Specifications 11
Cable Specifications 12

RJ-45 Pin Assignments 12
RJ-45 Cable Pin Assignments 12

Fiber Optic Cable Connection

Specifications 13

Contacting Technical Support 14

IFS MC201-1P/1FS User Manual i

Overview

Thank you for purchasing the IFS MC201-1P/1FS 10/100Mbps
Ethernet Twisted pair to 100Base-FX fiber optic PoE Bridge
Converter. This converter is used to convert one type of media
signal to a different type of media that allows two segments to
connect easily, efficiently and inexpensively. The converter
supports Power over Ethernet to power one IEEE 802.3af
compliant powered device.

About the MC201-1P/1FS

The MC201-1P/1FS is an IEEE 802.3af Power over Ethernet
Converter that supplies 48 VDC over Ethernet cable. The
MC201-1P/1FS IEEE 802.3af Power over Ethernet Converter
inserts DC Voltage onto a Category 5 cable, allowing the cable
between the Converter (MC201-1P/1FS) and PoE PD
(Powered Device) to transfer data and power simultaneously.
The maximum distance between the Converter (MC201­1P/1FS) and PoE PD is 328 ft. (100m). MC201-1P/1FS
combines Ethernet with IEEE 802.3af power and transfers
over the twisted pair cables. A PoE splitter can be used to
separate the Ethernet data and power if needed to power a
non-PoE device.

With the MC201-1P/1FS, only one Ethernet cable is needed to
carry both power and data to each device providing simpler
network designs, higher reliability while reducing costs.

Note: PSE (Power Sourcing Equipment) is a device (switch, or

hub for instance) that will provide power in a PoE setup. The
maximum allowed continuous output power per such device is

15.4W according to the IEEE 802.3af standard.

IFS MC201-1P/1FS User Manual 1

PD (Powered Device) is a device powered by the PSE and

thus consumes energy, such as IP Phones, network cameras
and Wireless access points, etc.

Package Contents

Open the package containing the MCR205-1T/1S and
carefully unpack it. The box should contain the following items:

• MCR205-1T/1S PoE Media Converter x1

• User’s Manual CD x1

If any of these items are missing or damaged, please contact
your dealer immediately. If possible, retain the product box
including the original packing material to return it for
repair/replacement.

2 IFS MC201-1P/1FS User Manual

Hardware Overview

Figure 1: Physical Layout

IFS MC201-1P/1FS User Manual 3

Front Panel

There is one RJ-45 Twisted-Pair jack (Auto-MDI/MDI-X), one
fiber-optic connector and four LED indicators on the MC201­1P/1S front panel.

Back Panel

There is one DIP switch for turning the Link Fault Pass­through feature on or off, and 48V DC power input located at
the back panel. The back panel also has one 48 VDC power
socket for the MC201-1P/1S.

Note: Please make sure that the 48VDC power supply used is

capable to provide 0.32A to support full PoE load.

Link Fault Pass-through (LFP)

The LFP function refers to the Link Fault Pass-through
function (LLCF/LLR) and the DIP Switch design. LLCF/LLR
can immediately notify administrators about a connectivity
problem. The DIP Switch enables or disables the LFP function.

4 IFS MC201-1P/1FS User Manual

LLCF (Link Loss Carry Forward) detects the connection loss
on the TP line, and LLR (Link Loss Return) detects the
connection loss on the fiber line.

Link Loss Carry Forward (LLCF)

The MC201-1P/1FS incorporates an LLCF function for
troubleshooting a remote connection. When LFP function is
enabled, the FL/TP ports do not transmit a link signal until they
receive a link signal from the opposite port.

The diagram below shows a typical network configuration with
a good link status using MC201-1P/1FS for remote
connectivity.

In case of a connectivity issue, the MC201-1T/1FS media
converter LLCF sends the notification to the switch/hub that
generates a trap to the management station.

* The default is set to OFF for LFP function.

IFS MC201-1P/1FS User Manual 5

Link Loss Return (LLR)

The fiber ports of the MC201-1P/1FS have been designed with
an LLR function for troubleshooting a connectivity issue. LLR
works in conjunction with LLCF.

When LFP function is enabled, the port’s transmitter shuts
down when its receiver fails to detect a valid connection. LLR
should only be enabled on one end of the link and is typically
enabled on either the unmanaged or remote device.

The diagram below shows a typical network configuration with
a good link status using MC201-1P/1FS for remote
connectivity. Note that LLR and LLCF are enabled as indicated
in the diagram.

If one of the optical conductors is bad (as shown in the
diagram box below), the fiber converter with LLR function will
return a no-link condition to its link partner. With LLCF function
also enabled, the no-link condition is carried forward to the
switch/hub where a trap is generated to the management
station.

6 IFS MC201-1P/1FS User Manual

Note: LFP function is turned-off by default. This feature can

also be enabled or disabled via the side DIP-switch. If the
installer is familiar with the network installation and diagnostics
(i.e. checking which end is broken in a connection), switch can
be set to ON position and converter should be reset for
changes to take effect. Otherwise, it's recommended to keep
the DIP switch in its default position.

Installing the Converter

Please follow these steps to install the MC201-1P/1FS:

1. Turn off the power of the network device/station in the
network to which the MC201-1P/1FS will be attached.

2. Ensure that there is no activity on the network.

3. Attach the fiber cable from the MC201-1P/1FS to the fiber
network. TX/RX must be paired at both ends.

4. Attach a Category 5 UTP cable from the 10/100Base-TX
network to the RJ-45 port on the MC201-1P/1FS.

5. Connect the 48V DC power adapter to the MC201-1P/1FS
and verify that the Power LED illuminates.

6. Turn on the network device/station, the TX Link and FX
Link LEDs should illuminate when all the cables are
attached.

IFS MC201-1P/1FS User Manual 7

r

TX

RX

100Base-FX Fiber

Network

RX

TX

10/100Base-TX

Cat. 5/5e TP

Cable Network

Note: RJ-45/STP, UTP Cat 5, straight /crossover cable is

accepted.

Please refer to the Cable Specification section for more details
about the wiring distance of your TP, optical fiber networks.

PoE Function

The MC201-1P/1FS IEEE 802.3af Powered Device/Splitter
equipment installation:

It's recommended to check your network environment before
the installation. The MC201-1P/1FS media converter sends
the power over the twisted pair cable (pair 1, 2 and pair 3, 6).

For locations where it may be difficult to find a power outlet,
the MC201-1P/1FS provides the easiest way to power your
PoE powered Ethernet devices such as IP cameras, IP access
control, VoIP, Wireless Access Points (WAP), etc.

2km~15km 100 meters

Data Data+Power

Fiber Switch

Powe

8 IFS MC201-1P/1FS User Manual

PoE

Wireless AP

Note: The PoE feature requires the use of a recommended

power adapter.

LED Indicators

System

LED Color Function

PWR

10/100Base-TX Port

LED Color Function

LNK/ACT

PoE in Use

Green Lit

Blink

Green

Green

Lit

Off

Lit

Off

Indicates the device is po wered.

Indicates that the Media Converter is
actively sending or receiving data over that
port.

Indicates that the connection through the
port is successfully established.

Indicates that the connection through the

port is not established.

Indicates that the port is providing PoE to
the connected device.

Indicates that the port is not providing PoE
to the connected device.

100Base-FX SC Port

LED Color Function

Blink

LNK/ACT

Green

Note: Fiber optic port should be set to the correct mode

according to this LNK/ACT indicator for optimal network
performance.

IFS MC201-1P/1FS User Manual 9

Indicates that the Media Converter is actively
sending or receiving data over the port.

Lit

Indicates that the port link is up.

Off

Indicates that the port link is down.

10 IFS MC201-1P/1FS User Manual

Specifications

Ethernet

Data Rate 10/100/1000Mbps
Throughput (packet per second) 148810pps@64Bytes
Switch Architecture Store-and-Forward

Flow Control

Connector
Cable Type and Distance 10Base-T (Cat 3, 4, 5e) or 100Base-T (Cat 5e) – 328ft (100m)

Fiber MC100FX-TX-PoE MC201-1P/1FS

Data Rate 100Base-FX 100 Base-FX

Connector SC SC

Fiber Type Multi-mode (50/125μm or 62.5/125μm Single mode (9/125μm)

Distance Up to 2km Up to 15km

Power Over Ethernet (PoE)

PoE Standard IEEE 802.3af

Power Pin Assignment (+) Pins 1 & 2; (–) Pins 3 & 6

Power Output (Max. 1 PoE Device) PoE 48 VDC, Max. 15.4 watts, 350mA

LED Indicators

Power Status On - Green

10/100Base-T Link Data Activity - Green

100Base-FX Link Data Activity - Green

PoE In Use Detection of PSE Device - Green

LFP Mode Switch

On If either TX or FX port is faulty, disable other port

Off Active link LED will still operate if other port is faulty

Electrical and Mechanical

Input Power 48VDC @ 0.38A

Enclosure Metal

Dimensions (H x W x D) 1.02 x 2.76 x 3.82 in. (26 x 70 x 97 mm)
Weight 0.44 lbs. / 200g

Environmental

Operating Temperature 0ºC~50ºC

Storage Temperature -120ºC~70ºC
Relative Humidity 0%–90% (non-condensing)

Back pressure for Half-Duplex mode

Pause from for Full-Duplex mode (IEEE 802.3x)

RJ-45 with Auto-MDI/MDI-X and PoE injector function

IFS MC201-1P/1FS User Manual 11

Cable Specifications

Duplex Connection Limitation (max.)
Twisted Pair

Half / Full Node to Node

Node to Switch/Hub

Single-Mode Converters

SM Full Node to Node

Node to Switch

100 meters

15 kilometers

RJ-45 Pin Assignments

10/100Mbps, 10/100Base-TX

Contact MDI MDI-X

1 1 (TX +) 3

2 2 (TX -) 6

3 3 (RX +) 1

6 6 (RX -) 2

4, 5, 7, 8 Not used Not used

Implicit implementation of the crossover function within a
twisted-pair cable, or at a wiring panel, while not expressly
forbidden, is beyond the scope of this standard.

RJ-45 Cable Pin Assignments

12 IFS MC201-1P/1FS User Manual

There are 8 wires on a standard UTP/STP cable and each
wire is color-coded. The following shows the pin allocation and
color of straight cable and crossover cable connections:

Fiber Optic Cable Connection Specifications

The optical details are shown below:

Fiber Optical patch Cables:

Standard Fiber Type Cable Specification

100Base-FX

(1310nm)

100Base-FX

(1310nm)

Multi-mode 50/125μm or 62.5/125μm

Single-mode 9/125μm

IFS MC201-1P/1FS User Manual 13

Contacting Technical Support

Contact technical support if you encounter any difficulties
during this installation. Please make sure you have the
requested diagnostic or log files ready before you contact us
by phone or go to www.interlogix.com/customer-support.

Technical Support

Europe, Middle East and Africa

W Select Contact Us at www.utcfssecurityproducts.eu

North America

T +1 855.286.8889

E [e-mail]

Australia

E [e-mail]

14 IFS MC201-1P/1FS User Manual