Interlogix ITI Simon, Simon Owner's Manual

S I M O N O W N E R ' S M A N U A L

FCC Notices

FCC Part 15 Information to the User

Changes or modification s not expressly approved by Interlogix Inc . can void the user’s authority to operate the equipment.

FCC Part 15 Class B

This equipment has been tested a nd found to comply with the limits for a Class B digit al device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasona ble prot ection against interference in a residential installation.

This equipment generates, uses, and can radia te radio frequency ene rgy and, if not installed and used in ac cordance with the instructions, may cause harmful
interference to radio comm unications. However, there is no guarante e tha t in te rfe rence will not occur in a particul ar installation.

If this equipment does cause harm ful interference to radio or tel evision reception, which can be de t erm i ned by turning the equipment off and on , the user is
encouraged to try to corre ct the interference by on e or m ore of the following meas ure s :

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the affected equipm ent and the panel receiver to separate outlets, on differe nt branch circu it s .

• Consult the dealer or an experienced radio/TV technician for hel p.
FCC ID: B4Z-787E-SIMON

ACTA Part 68

This equipment co m pli es with Part 68 of the FCC Rules. Located on this equipme nt i s a lab el that contains, among other information, the FCC registra tion
number and the ringer equiv al en ce number (REN) for this equipme nt . If re quested, this information must be pro vided to the telephone company.

FCC Part 68 Registration No. B4ZUSA-27621-AL-E REN: 0.2 B
The REN is used to determine the maximum number of devices that may be connected to your telephone line. Excessive RENs on a telephone line may result

in devices not ringing in response to an in com i ng call. In most areas, the sum of all device RENs should not exceed five (5.0 ). To be certain of the number of
devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. For products approved after July 23, 2001, the
REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by # # are the REN wit h ou t a decimal
point (e.g., 03 is a REN of 0.3). For earl ie r products, the REN is separately shown on the label.

A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and require­ments as adopted by ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compliant modular
jack that is also compliant. See the Installation Instructions for details.

Alarm dialing equipment must be able to seize the telepho ne line and place a call in an emergenc y situation. It mu st b e able to do this even if other equipment
(telephone, ans w er in g system, computer modem, etc.) already has the te lephone line in use. To do so, alarm dialing equipment must be connected to a prop­erly installe d RJ31X jack that is el ectr ically in seri es and ahea d of all ot her equipme nt attach ed to the same teleph one lin e. Proper installation is depicted in the
following diagram. If you have any questions concerning these instructions, consult your local telephone company or a qualified installer about installing an
RJ31X jack and alarm dialing equipment for you.

C u s t o m e r P r e m i s e s E q u i p m e n t a n d W i r i n g

N e t w o r k
S e r v i c e
P r o v i d e r ' s
F a c i l i t i e s

T e l e p h o n e
L i n e

N e t w o r k
D e m a r c a t i o n
P o i n t

T e l e p h o n e

R J 3 1 X

J a c k

If this equipment causes harm to the te lephone network, the telephone company may tempo rarily disconnect your service. If po ssi ble, you will be notified in
advance. When advance notice is not practical, you will be notified as soon as possible. You will also be advised of your right to file a complaint with the FCC.

The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of the equipment. You will be
given advance notice in order to maintain uninterrupted service.

If you experience trouble w i th this equipment, please c ont act the company that insta ll ed the equipment for service a nd/or repair information . T he telephone
company may ask you to disconnect this equipment from the network until the problem has been corrected or you are sure that the equipment is not mal func­tioning.

This equipment may not be used on coin service provided by the te le phone company. Connection to party lines is subject to state tariffs

U n u s e d

R J - 1 1 J a c k

A n s w e r i n g
S y s t e m

A l a r m D i a l i n g
E q u i p m e n t

F a x M a c h i n e

T e l e p h o n e

C o m p u t e r

U n u s e d
R J - 1 1 J a c k

T e l e p h o n e

Canada Notice

The Canadian Department of Communic ations label identifies certified equipment. This certification means tha t the equipment meets certai n telecommunica­tions network protective, operational, and safet y requirements. The de partment does not guarantee the equipment will operate to t he user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The
equipment must also be installe d usi ng a n acceptable method of conn ec ti on. In some cases, the company’s inside wiring associate d wit h a single-line individ­ual service may be extended by means of a certified co nne ctor assembly (teleph one extension cord). The cu sto me r should be aware that compliance with the
above conditions may not pr event degradation of servic e in som e si tuations.

Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by
the user to this equipment, or equipment malf unctions, may give the telecommunicati o ns co mp an y cause to request the user to disco nnect the equipmen t.

For your protection, make sure that the electrical grou nd c onnections of the power utility, telephone lines, and int ernal metallic water pipe system, if present,
are connected together

Do not attempt to make connections yourself. Contact the appro priate electrician or elec-

!

Caution

The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is used by the
device, to prevent overloading. The termination on a loop may consist of any combination of devices subject only to the requirement that the total of the LNs
of all the devices does not exceed 100. Load Number: .1 The term “IC:” before the certification/registration number only signifies that the Industry Canada
technical specifications were met. IC: 867A 787SIMON

“AVIS: - L ´étiquette du ministère des Communications du Canada identifie le matériel homologué. Cett e ét iquette certifie que le matériel est conforme a cer­taines normes de protection, d ´ exploitation et de sécurité des rése aux de télécommunications. Le ministère n ´ assure toutefois pas que le matériel fonction­nera a la sati s f action de l ´ utilisateur.

Av an t d ´ installer ce matériel, l ´ utilisateur d oi t s ´ assurer qu´ il est permi s d e le raccorder aux inst all ations de l ´ enterprise locale de téléco mmu n ication. Le
matériel doi t également etre ins tallé en suivant u n e méthod acceptée d e raccordement . Dans certains cas , les fils intér ieurs de l´ enterprise utilisés pour un ser­vice individuel a ligne unique peuvent etre prolongés au m oye n d´ un dispositif homologué de racc ordement (cordon prolonga t eur tél éphonique interne). L ´
abonné ne doit pas oublier qu ´ il est possible que la conformité aux conditions énoncées ci-dessus n ´ empechent pas le dégradation du service dans certaines
situations. Actu el lement, les enterpr ises de télécommun ica tion ne permettent pas que l ´ on ra cco r d e leur matériel a d es jacks d ´ abonné, sauf dans les cas pré­cis prévus pas les tarrifs particuliers de ces enterprises.

Les réparations de matérie l ho mologué doivent etre effectué es pa s un centre d ´ entretien canadien autorisé désigné par le fournisseur. La compagne de télé­communications peut dema nder a l ´ utilisateur de débranche r un appareil a la suite de réparations ou de modifi ca ti ons effectuées par l ´ utilisateur ou a cause
de mauvais fonctionnement.

Pour sa propre protection, l ´ utilisat e ur doit s ´ assurer que tous les fils de mise a la terre de la sou rce d ´ énergie électrique, des lignes téléphoniq ue s et des
canalisations d ´´ eau métalliques, s ´ il y en a, sont raccordés ensemble. Cette précaution est particulièrement importante dans les régions rurales.

Avertissment. - L ´ utilisateur ne doit pas tenter de faire ces raccordements lui-meme; il doit avoir recours a un service d ´ inspection des installations élec­triques, ou a electricien, selon le cas”.

Une note explicative sur les indices de charge (voir 1.6) et leur emploi, a l ´ intention des utilisateurs du matériel terminal, doit etre incluse dans l ´ information
qui accompagne le mate rie l ho mologué. La note pourrait etre rédigée selon le modèle suivant:

“L ´ indice de charge (IC) assigné a chaque dispositif terminal indique, pour éviter toute surcharge, le pourcentage de la charge totale qui peut etre rac c ordée a
un circuit téléphonique bouclé utilisé par ce disposit if. La te rminaison du circuit bouclé peu t et re constituée de n ´ import som m e de s ind ic es de charge de l ´
ensemble des dispositifs ne dépasse pas 100.”

L ´ Indice de charge de cet produi t est ____________.

tric inspections authority.

)

*(,QWHUORJL[

*(,QWHUORJL[6LPRQLVDWUDGHPDUNRI*(,QWHUORJL[$OORWKHUWUDGHPDUNVDUH
SURSHUWLHVRIWKHLURZQHUV)RUUHSULQWVRUGHUGRFXPHQW5HY'

$OOULJKWVUHVHUYHG

6HFRQG6WUHHW1RUWK
1RUWK6DLQW3DXO01

TABLE OF CONTENTS

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Security System Beeps, Lights, and Messages . . . . . 3

How to Use Your Control Panel. . . . . . . . . . . . . . . . . . . 5

How to Use Your Touchpads . . . . . . . . . . . . . . . . . . . . . 8

Programming Your System . . . . . . . . . . . . . . . . . . . . . . 9

System Tests & Trouble Beeps . . . . . . . . . . . . . . . . . . .12

Your Emergency Evacuation Floor Plan . . . . . . . . . . . .14

Alarm System Limitations . . . . . . . . . . . . . . . . . . . . . . .15

Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Quick Reference Table . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

Important Messages to the Owner:

In the following parag raphs there may be some terminology th at you are not famil iar with. Reread thi s section after you fa miliarize
yourself with your security system.

Arming Your System with Doors or Windows Open:
after the exit dela y has ex pired. This m eans they wi ll not be prot ecting your h ome. If you wish to bypas s a s ensor a fter yo u ha ve
armed your system , you must first disarm the syste m, then open the door or wi ndow which yo u want byp assed. You r system wi ll
tell you if a protected door or window is open when you arm the system. If your system includes 24-hour protection sensors on
items such as gun or j ew el ry cas e s , y ou mu st do an additional di sa rm c al led subdisarm before accessing t hes e a r eas to av oi d
causing an alarm. The master acc ess code and pa nic code can subdisarm. Wh en the system is disarmed, us ing the Cont rol Pan­el, the Remote Handh eld Touchpad, or Toucht alk 2-Way RF Touchpa d, enter the master acce ss code or panic code t o subdisarm
the system. The Control Pan el is sub dis arm ed when the Disarm button is flashing. If the panic co de was use d, an al arm will be
reported to the central station.

CAUTION! If you use the Control Panel to arm your security system when leaving your home, you need to be aware of the fol­lowing: You need to exit before the end of the delay peri od or an alarm wil l sound .
or 4 beeps at the beginnin g of the ex it delay (see the ta ble “Pane l Beeps ” on pag e 3 of this manual to determine the meaning of
control panel/system beeps). At the end of the exit delay, the system beeps 2, 3, or 4 additional beeps. If you exit at that time
(after the exit delay), your system assumes you are now returning to your home. The system is now counting down the entry
delay time and will expect you to disarm the system within the entry delay time or it will alarm.

Something may have happened while you were away! If you enter your home and controlled lights that are normally off are
on and/or you hear alarm sirens, an intruder may be inside or another emergency may have occurred. Leave immediately, and
call for non-medical emergency help.

Canceling Accidenta l Alarms : You have up to 120 sec onds (programmab le by the ins talle r) after caus ing an accid ental al arm to
disarm your securit y syste m. See y our in stalle r to det ermine this a mount of tim e. If th e progra mmed seco nds ha ve pass ed, yo u
must call the central monitoring station to cancel the alarm.

Any sensors which are open when the system is armed will be bypassed

Remember, when y ou arm y ou will hear 2, 3,

Notices for UL-Listed Installations:

• This system is suitable for Grade A household burglary applications.

• The Freeze Sensor, Glass Guard and Shock Sensors are not UL Listed.

• The garage door opening feature used with this system has not been evaluated by UL.

1

Introduction to Your System

Your security system uses wireless technology to warn your
family about intrusion and fire. It may also be used to control
lights and appliances within your home.

The system is designed to be monitored and/or to send mes­sages to a numeric pager.

The security system uses devices called sensors which use
radio waves to communicate alarms to the Control Panel.

The system is supervised, meaning that the Control Panel
checks the status of each sensor to detect problems. If the
Control Panel detect s tr oub le i t w il l n oti fy y ou with beeps and
indicator lights on the Control Panel itself.

Typical Security System Components

A typical security system ins tal lation consists of the following
devices:

Control Panel

The Control Panel is us ed to ope rate an d program your secu­rity system. It commu ni cat es to yo u through panel voice me s­sages, panel beeps, and by lighting buttons on the Control
Panel. The Control Panel can communicate to a central mon­itoring station and/or a nu meric pager. The Control Pan el may
come with 2-Way Voice On-Board.” This feature allows the
Central Station to commun icate with the user if there is a prob­lem at the security system site.

Audio Verification Module (Not for use with Basic

Model)

The Audio V erific ation Module (AVM) gives the central st ation
operator the ability to hear what ’ s happ eni ng at the prem is es
during an alarm and speak directly to the system owner. The
operator can determ ine how serio us an alarm i s, find out w hat
kind of help is needed, and dispatch the appropriate assis­tance.

Remote Handheld Touchpad and Touchtalk 2­Way RF Touchpad

These touchpads are used to control the security system pri­marily from within the home.

(Not for use with Basic Model)

KeyChain Touchpads

KeyChain Touchpads are used to contro l the se cur ity syste m
from within or near the outside of your home.

Indoor Motion Sensors

Indoor Motion Sensors dete ct moti on . They ma y be use d for
intrusion protection or to sound chimes on the Control Panel.

Outdoor Motion Sensors

Outdoor Motion Se nsors det ect motio n in a pro tected ou tdoor
area and can sound chim es or turn on outside lights. The y are
not used for intrusion detection.

Door/Window Sensors

Door/Window Sensors detect the opening of a door or win­dow.

Smoke Sensors

Smoke Sensors detect smoke. They have a built in siren
which sounds when smoke is detected.

Modules (Not for use with Basic Model)

Modules are used to control lights, appliances, and a garage
door. Only unit numbers 1-8 may be used for individual light,
appliance, or garage door control.

KEYCHAIN

TOUCHPAD

TOUCHTALK

2-WAY RF

TOUCHPAD

AUDIO VERIFICATION
MODULE

2

DOOR/WINDOW

SENSOR

CONTINUOUS

MOMENTARY

GARAGE DOOR

MODULE

ON

1

3

15

5

13

11

7

9

UNIT CODE

X-10 POWERHOUSE

MOTION
SENSOR

OFF

A

C

O

E

M

GK

I

HOUSE CODE

SOUNDER ONLY

SOUNDER & RELAY

RELAY ONLY

15

13

11

O

M

LAMP

MODULE

1

3

5

7

9

A

C

E

GK

I

APPLIANCE

MODULE

SMOKE

SENSOR

1

3

15

5

13

11

7

9

A

C

O

E

M

GK

I

SYSTEM
STATUS

ARM

Doors &

Windows

ARM

Motion

Sensors

DISARM

3

1

4

526

7

89

Off

On

EMERGENCY

sP

d&sre s Hol hBtoeKy

-

REMOTE
HANDHELD
TOUCHPAD

C A R B O N
M O N O X I D E

D E T E C T O R

CARBON MONOXIDE

ALARM

8988G21D.DSF

Security System Beeps, Lights, and Messages

Your security syst em comm unica tes to yo u th rough the use of pa nel vo ice me ssag es, pan el beep s, indi cator li ght s on the panel
itself, and to a numeric pager if programmed.

You communicate to your security system with key presses on the Control Panel, touchpads, or through the use of a remote
telephone. Disarming and programming require you to input a 4-digit access code. The Master Access Code default is 1-2-3-

4 when the security system is shipped from the factory. You should change it to a code known only by you.

Panel Voice Messages

When you press the buttons on the Control Panel or the touchpads, the Control Panel responds with voice messages. Panel
voice can be enabled or disabled (see “What You Can Change:” on page 9).

These messages may res pon d wi th s ys te m i nfo rma tio n or prom pt yo u to tak e f urth er ac ti on. For example, if you want to dis arm
the system and you press the DISARM button, the Control Panel responds by saying, Please enter your access code.

If you press a button an d the feature has not been pr ogrammed into th e Control Pane l, the panel vo ice will respo nd with Function
not available. An example of this situation is pressing the Control Panel button CHIME Special Motion when you have no non-
intrusion Motion Sensors in your installation. The panel voice would respond with, Function not available.

Panel Beeps

Panel beeps are used to indicate keypresses, status, and problems with the system. Panel beeps can be enabled or disabled
(see “What You Can Change:” on page 9).

Use the following table to understand the beeps used by the security system.

Activity Beep Response
ARM Doors & Windows Exit delay beeps sound 2 times when you arm* and 2 times at the end of the delay time;

Entry delay beeps sou nd 2 times ev ery 5 seco nds and 2 tim es per seco nd during the last 10

seconds

ARM Motion Sensors Exit delay beeps sound 3 times when you arm* and 3 times at the end of the delay time;

Entry delay beeps sou nd 3 times ev ery 5 seco nds and 3 tim es per seco nd during the last 10
seconds

ARM Doors/Windows &
Motion Sensors

DISARM 1 beep
CHIME DOORS 2 beeps (feature must be programmed by installer)
CHIME SPECIAL MOTION

(Not Included in Basic
Model)

Trouble Beeps 6 beeps every minute. Press SYSTEM STATUS button twice to stop beeps for 4 hours
No Activity Beeps 20 beeps every minute for 5 minutes (feature must be programmed by the installer)

* You will not get initial exit delay beeps if you are arming from a Touchtalk 2-Way RF Touchpad.

Note: You may receive a different number of panel beeps if buttons are pressed quickly.

Exit delay beeps sound 4 times when you arm* and 4 times at the end of the delay time;
Entry delay beeps sou nd 4 times ev ery 5 seco nds and 4 tim es per seco nd during the last 10

seconds

3 beeps (feature must be programmed by installer)

3

Alarm Sirens and Lights

Exterior and interior sirens make 3 different alarm sounds on the premises, each indicating a different type of alarm. Sirens will
time-out and stop sounding after the siren timeout (programmable by the installer). System controlled lights also indicate the type
of alarm.

Use the following table to understand alarm sounds and controlled lights.

Alarm Type Interior Siren Sound Exterior Siren Sound System Controlled Lights

(Not Included in Basic Model)

Fire (Temporal 3) 3 siren pulses then off

for 2 seconds, 3 siren
pulses then off for 2
seconds, . . .

Intrusion On steady On steady Flashing

Emergency Fast on-off _________________ On steady

3 siren pulses then off
for 2 seconds, 3 siren
pulses then off for 2
seconds, . . .

On steady

Panel Indicator Lights

Use the following table to understand the panel indicator lights.

Button When the Button Light is On When the Button Flashes

ARM Doors & Windows Doors/Windows armed Doors/Windows armed &

No Entry Delay on

ARM Motion Sensors Motion Sensors armed Motion Sensors armed &

Latchkey on

DISARM System disarmed System subdisarmed

SYSTEM STATUS System trouble or Open Sensor System in alarm

CHIME Doors Door will cause chime _____________________

CHIME Special Motion
(Not Included in Basic Model)

Motion will cause chime _____________________

LIGHTS Time Activated
(Not Included in Basic Model)

LIGHTS Sensor Activated
(Not Included in Basic Model)

Light schedule is on _____________________

Sensors will cause light to go on _____________________

Numeric Pager

You may program your security system to send a numeric message indicating system activities to your pager. The system will
send the message twice. See “Programming Your System” on page 9.

Use the following table to determine what the numeric message is reporting.

Reports Numeric Message Reports Numeric Message

Phone Test -101 -101 Intrusion -108 -108

AC Power Restoral -102 -102 Fire -109 -109

AC Power Failure -103 -103 Disarming -110 -110

Latchkey -104 -104 Arming -111 -111

No Activity -105 -105 Fail to Disarm -112 -112

Panic Code -106 -106 Fail to Arm -113 -113

Emergency -107 -107

4

How to Use Your Control Panel

The Control Panel interface consists of 3 columns of buttons. They are: HOME SECURITY, CODE, and HOME CONTROL.
There is a non-medical EMERGENCY button located on the far right.

HOME SECURITY
ARM Doors & Windows. Press once to turn the secu-

rity system protection on for all protected doors and windows.
If a door or window is open when you arm the system, it will
be bypassed, meaning not protected. The SYSTEM STATUS
light will be lit.

Press twice to eliminate the preprogrammed entry delay. The
ARM Doors & Windows button blinks when No Entry Delay is
on.

ARM Motion Sensors. Press once to turn protection on

for all intrusion Motion Sensors. Use when no one is home.
This is usually used in combination with ARM Doors & Win-
dows.

Press twice to activate Latchkey. Latchkey is used to notify
parents if children do not arrive home at a predetermined time
and disarm the system. The ARM Motion Sensors button
blinks when Latchkey is on.

DISARM. Press once and enter your access code using

the CODE buttons to turn security protection off. Some sen­sors, for example smoke detectors and panic devices, are still
active even when the system is disarmed.

SYSTEM STATUS. Press twice to hear information

about your system. If the button is lit, there is a problem with
the system. If the button is blinking, an alarm has occurred.
Press the button to hear what is wrong with the system. See
“System Tests & Trouble Beeps” on page 12. Press SYSTEM

STATUS then the 7 - 8 button to turn all lights on. Press SYS-
TEM STATUS then the 9 - 0 button to turn all lights off. (Not
for use with Basic Model)

CODE

There are 5 CODE buttons located on the left side of the Con-
trol Panel. Each button represents 2 numbers. The top CODE
button is 1 - 2 which means that this button is pressed when
entering either 1 or 2. For example, if your access code is 1-
2-3-4 you must press the 1 - 2 button twice and the 3 - 4 button
twice.

If your system includes 24-hour protection sensors on items
such as gun or jewelry cases, you must subdisarm the Control
Panel before accessing these areas to avoid causing an
alarm. To subdisarm the system when it is already disarmed,
enter the master access code. The DISARM button will flash
when the Control Panel is subdisarmed.

HOME HOME
SECURITY

CODE

1 - 2

ARM
Doors &
Windows

3 - 4

ARM
Motion
Sensors Motion

5 - 6

DISARM

7 - 8

SYSTEM
STATUS

9 -

0

Test Weekly

CONTROL

CHIME
Doors

CHIME
Special

LIGHTS
Time
Activated

LIGHTS
Sensor
Activated

EMERGENCY

8988G12B.DS4

5

HOME CONTROL

If any of the HOME CONTROL buttons are pressed and a sen­sor or module is not associated (programmed) with this fea-

ture the Control Panel will say, Function not available.

CHIME Doors. Press to cause the Control Panel to beep

when protected doors or windows are opened.

This is a nice feature to use if you’re busy in one part of
your home and you want to know when family members
are going in and out of your home.

CHIME Special Motion. (Not Included in Basic

Model)

Press to cause the Control Panel to beep when Motion Sen­sors detect movement within a specific area. These Motion
Sensors are not used for intrusion protection.

If you have Motion Sensors located in areas such as in a
patio area or at the front door and you want to know when
someone is approaching these areas, you would use this
feature.

LIGHTS Time Activated. (Not Included in Basic

Model)

Press to enable system controlled lights to turn on and off at
scheduled times.

An example is turning your living room lights on at 7 pm
and off at 10 pm.

LIGHTS Sensor Activated. (Not Included in Basic

Model)

Press to have specially programmed sensors turn on lights for
4 minutes when sensors are tripped.

An example is using an outdoor Motion Sensor at the front
door. When the Motion Sensor detects movement it will
cause the light at the front door to turn on.
You may also program the star button on the KeyChain
Touchpad to turn on a light for 4 minutes. The KeyChain
Touchpad star key will always work, even when sensor
activated lights are disabled.

EMERGENCY

Press EMERGENCY for 2 seconds or twice quickly to call the
central monitoring station and notify them of a non-medical
call for help.

If the decal pictured below (shown in gray) is on your panel,
you can press the EMERGENCY button then one of the other
3 buttons (intrusion, auxiliary, or fire) to call the central moni­toring station or a numeric pager.

HOME HOME
SECURITY

CODE

1 - 2

ARM
Doors &
Windows

3 - 4

ARM
Motion
Sensors Motion

5 - 6

DISARM

7 - 8

SYSTEM
STATUS

9 -

0

Test Weekly

CONTROL

CHIME
Doors

CHIME
Special

LIGHTS
Time
Activated

LIGHTS
Sensor
Activated

EMERGENCY

8988G12C.DS4

6

How to Use An Off-Site Phone for Remote Phone Control (Not Included in Basic Model)

You may use an off-site phone to arm/disarm your Control
Panel, toggle lights, check system status, or conduct an audio
session (ask your installer if you have this feature). To gain ac­cess to the Control Panel:

1. Call the Control Panel and let the phone ring twice then
hang up.

2. Wait at least 10 seconds and call the Control Panel
again. You may wait up to 40 seconds before calling
again.

3. The Control Panel should answer on the first ring. You
won’t hear any prompt when the system answers.

4. Press the * button on your telephone and you will hear

system activated.

At this point you may perform the actions listed in the first
paragraph of this page.

For example, to check system status:

Press * + CODE + # + 1 on your telephone. CODE is any
access code programmed into your Control Panel.

Note: Press * + CODE + 9 to ha ng up or your security sys­tem site phone may be busy for up to 90 seconds after
your disconnect.

Note: If you are interactive with your Control Panel and the

panel hangs up on you, the system is calling in a report to the
central monitoring station or a pager, due to an action made
by you or someone at the security system site.

The following table identifies the phone commands to be used
when using remote phone control.

Phone Commands for Remote Access

Control Panel Function Phone Command

DISARM * + CODE + 1

ARM Doors/Windows * + CODE + 2

ARM Doors/Windows with
No Entry Delay

ARM Motions * + CODE +3

ARM Motions with Latchkey * + CODE + 3 + 3

ARM Doors/Windows and
Motions

ARM Doors/Windows with
No Entry Delay and Motions
with Latchkey

Toggle Lights * + CODE + 0

System Status * + CODE + # + 1

Audio Session * + CODE + 5 + X (X = a

Hang Up * + CODE + 9

* + CODE + 2 + 2

* + CODE + 2 + 3

* + CODE + 2 + 2 + 3 + 3

command from the audio
session command set).
See Table on page 7

2-Way Voice Audio Sessi on (Not Included in Basic

Model)

An audio session may be conducted from off site. You can call
the security system site and talk to the people present and
they can talk to you using the speaker and microphone on the
Control Panel.

Note: Ask your installe r if y ou h ave this fea t ure a vai lable
to you.

Do the following to conduct an audio session:

1. Follow the instructions above for Remote Phone Control
to gain access to the Control Panel.

2. Press * + CODE + 5 on the phone to start the audio ses­sion.

3. Press 1 to speak or 3 to listen.
If you press 3 to listen you may notice a 5 second delay
before you can hear the Control Panel’s surroudings.
See the following table Audio Session Comman d Set
for the commands that can be used from an off site
phone.

4. Press 9 + 9 to hang up.

CODE = any access code

Audio Session Command Set

Phone

Button(s)

1 Speak

3 or 6 Listen

7 Extends the session for 90 more sec-

onds

99 Terminates session

Note: If 1, 3, 6, or 7 is pressed, the session time is extended
for 90 more seconds. The panel will sound time out warning
beeps when there are 20 and 10 seconds left of the session.

Audio Session

7

How to Use Your Touchpads

8988G07B.DS4

7

4

1

89

5

2

6

3

Off

sP

EMERGENCY

On

d&sre s Hol hBtoeKy

DISARM

SYSTEM

STATUS

Doors &

Windows

ARM

ARM

Sensors

Motion

-

Touchpads are used to control the security system from any location within or near your home. They have additional home control
features such as light and appliance control. When using the Touchtalk 2-Way RF Touchpad, beeps and voice feedback will be
heard from this touchpad and not from the Control Panel.

Remote Handheld Touchpad and Touchtalk 2-Way RF Touchpad (Not for use with Basic Model)

SYSTEM STATUS Press once to hear information about your system. See “System

Tests & Trouble Beeps” on page 12.

ARM Doors & Windows Press once to turn the security system protection on for all
protected doors and windows.
Press twice to eliminate the preprogrammed entry delay.

ARM Motion Sensors Press once to turn protection on for all Motion Sensors. Use
when no one is home. This is usually used in combination with ARM Doors & Windows.
Press twice to activate the Latchkey feature.

DISARM Press once and enter your access code using the NUMERIC buttons to turn
security protection off. To subdisarm the system, enter the master access code.

ON Light button Press twice quickly to activate all lights controlled by the security
system. You may turn on specific lights and appliances by pressing this button once and
entering the unit number of a light or appliance using the NUMERIC buttons.

KeyChain Touchpad

OFF Light button Press twice quickly to turn off all lights. You may turn off specific

lights and appliances by pressing this button once and entering the unit number of the
light or appliance.

EMERGENCY Press both EMERGENCY buttons for 3 seconds to cause the system to
call a central monitoring station to report a non-medical emergency.

LOCK Press once to arm doors and windows.
LOCK Press twice to arm doors, windows, and Motion Sensors.
LOCK Press 3 times to arm doors, windows, Motion Sensors, and to activate the

Latchkey option.

Entering your home

If your installer programmed the KeyChain Touchpad with no entry
delay, and you armed the system with the KeyChain Touchpad, you must disarm your
system from outside of the home to avoid causing an alarm.
Exiting your home

You have at least 5 seconds and up to 120 seconds (depending on

installer programming) to leave without causing an alarm.

LOCK and UNLOCK Press both buttons simultaneously for 3 seconds to send an
intrusion, silent, or non-medical emergency alarm to the central monitoring station.

UNLOCK Press to disarm your security system.

LIGHT Press to turn system controlled lights on or off.

STAR Press to open or close your garage door, if programmed, or your system may be

programmed to turn on a light using this button.

For any keypress on the KeyChain Touchpad, hold the button until the indicator
light blinks.

8

Programming Your System

What You Can Change:
Options:

Press Add in the START MENU and follow the voice prompts
to turn an option on.

Press Delete in the START MENU to turn an option off.

Option 01 - Panel Beeps

Panel Beeps are any beeps (including chime beeps) that
come from the Control Panel. Panel Beeps, except for
alarm sirens, may be disabled. See “Panel Beeps” on
page 3.

Option 02 - Panel Voice

Panel Voice may be disabled, except for status messages,
open sensor responses, and when in program mode.

Option 03 - Latchkey Time

Adding this option allows you to program Latchkey Time.
Latchkey is used to notify parents if children do not arrive
home at a predetermined time and disarm the system.

Option 36 - Sensor Activated Light Lockout Start Time
Option 37 - Sensor Activated Light Lockout Stop Time
(Not for use with Basic Model)

The Control Panel will not
by a sensor, even if sensor activated lights are enabled,
between the programmed start time (option 36) and the
programmed stop time (option 37).
Both options must be programmed for this feature to work.
The LIGHTS Sensor Activ ated button must be lit for lights
to turn on.

Option 41 - Voice Chime

The Control Panel will verbally announce which chime sen­sor has been tripped if the chime feature is on.

Option 42 - Speaker Level (Not for use with Basic Model)

Turn the Control Panel speaker level to the high voice level
when the option is turned on or turn the speaker level to the
low voice level when turned off.

Option 43 - Pager Phone Number

Up to 22 digits, including pauses, may be programmed for
the pager phone number.
Add 3 or 4 pauses to the end of the phone number to
ensure the complete pager message will be received.
Press the Test button to program a pause into the phone
number.

The Control Panel will call the pager to indicate:

• No activity - The no activity time period is programmed

by your installer. A no activity alarm is called in if the pro­grammed amount of time passes, the Control Panel is
subdisarmed, disarmed, or doors and windows armed,
and no activity has occurred (a key has not been
pressed or a sensor has not been tripped). Tripping of
non-intrusion chime sensors is not considered activity.

• Latchkey - A latchkey report is called when the system

turn on a light which is activated

is not disarmed by a predetermined time. The latchkey
time is programmed by the user - Option 03. Latchkey
must be enabled when arming.

• Phone Test - A phone test report is called in when a

phone test has been performed.

• Disarming - A disarming report is called in when the

system is disarmed. This option is programmed by your
installer.

• Arming - An arming report is called in when the system

is armed. This option is programmed by your installer.

• Fail to Disarm - A fail to disarm report is called in when

the system is not disarmed by the time programmed by
the installer.

• Fail to Arm - A fail to arm report is called in when the

system is not armed by the time programmed by the
installer.

• AC Power Failures - An AC power failure is called in 15

minutes after loss of power.

• AC Power Restoral - A restoral will be reported when

power is restored.

• Alarms - Alarm resports include: Emergency, Intrusion,

and Fire.

Sensor Test or Phone Test . A sensor test or phone

test can be performed by following the instructions given in the
section labeled “Manual Tests--What You Need to Test” on
page 13 of this manual.

Access Codes. Your security system has a master

access code, access codes 1-5, and a panic code. The mas­ter code is used for disarming and programming your system.
Access codes 1-5 are generally used for children or as tem­porary codes for a babysitter or service personnel and may
be used only for disarming. The panic code may be entered
to disarm or subdisarm the system in a non-medical emer­gency situation. The Control Panel will call the central station,
but there will be no indication of an alarm at the Control
Panel.

Note: Because different codes can be entered using the
same button presses you have to use caution when program­ming the panic code. You need to ensure that the panic code
does not use the same button presses as other access
codes. For example if the master code is 1234, do not pro­gram the panic code to be 2244. The Control Panel would
interpret these codes to be the same code.

Time Activated Lights. (Not Included in Basic

Model) Lights may be put on a time schedule.

Entry/Exit Activated Lights. (Not Included in Basic

Model) Lights will turn on for the delay period.

Sensor Activated Lights. (Not Included in Basic

Model) Lights will turn on for 4 minutes after a sensor is

tripped.

Set Clock. If the panel loses power, the clock must be set.
House Code. (Not Included in Basic Model) The house

code programmed into the panel should match the house
code set on lamp, appliance, and garage door modules.

9

Programming Using Panel Decals (Upper Decal and Lower Decal (Not Included in Basic Model))

The programming decals are visible when you open the Control Panel cover. These decals are designed to make system pro­gramming easier for you. Always begin by choosing a button from the START MENU. Follow the voice prompts and flow arrows
to complete the desired task. Notice the button flow diagrams under Instruction Summ ar y to the right of the buttons and on
the lower decal.

8988G37D.DSF

10

8988G38A.DSF

Step by Step Programming Instructions

Use the following instructions to access the programming but­tons and programming decals.

1. Open the C ontrol Panel Cover by pressing the plastic

latch on the top of the Control Panel.
When you open the cover you will immediately be
prompted by the Control Panel voice to use the red num­bered keys to enter your ID.

2. Enter Your Access Code.

The Master access code is 1-2-3-4 when the panel is

shipped. You should change it to a code know n only

by you.

3. The system voice will prompt you to begin with the

START MENU. The START MENU is located on the left

side of the upper decal.

The START MENU includes the following buttons:

Add
Delete
Cancel
Te st
Clock Set

Press the appropriate button.

4. After pressing a button on the START MENU the system
voice will prompt you to then use the MAIN MENU.

The MAIN MENU includes the following buttons:

Option #
Sensor/Remote
Access Code
Light Control

Press the appropriate button.

Depending on the button you pressed, the system will prompt
you to continue by pressing other buttons on the panel.

7. Close the Control Panel cover.

t h e n u s e n u m b e r k e y s t o e n t e r c o d e

How to Delete an Access Code

1. Open the cover of the Control Panel.

2. The panel voice prompts you to Use red numbered keys

to enter 4-digit ID. Enter your master access code

using the red numbered keys.

3. The panel voice prompts you to Please select from
START MENU. Press the Delete button on the START

MENU.

4. The panel voice prompts you to Sele ct from MAIN
MENU. Press the Access Code button on the MAIN

MENU.

5. The panel voice responds with Access Code 1, press

again for next access code or DONE to select or CAN­CEL to quit. Press the access code button again to hear

the next access code. When you hear the access code
you wish to delete, press the DONE Button. The panel
voice responds with Access Code X deleted .

6. Close the Control Panel cover.

Delete Access Code

Delete

8988G45B.DS4

Options

The following is a table of options you can change. See “What
You Can Change:” on page 9 for a description of these op­tions.

Option # Add Delete

How to Change an Access Code

1. Open the cover of the Control Panel.

2. The panel voice prompts you to Use red numbered key s

to enter 4-digit ID. Enter your master access code

using the red numbered keys.

3. The panel voice prompts you to Please select from
START MENU. Press the Add button on the START

MENU.

4. The panel voice prompts you to Sele ct from MAIN
MENU. Press the Access Code button on the MAIN

MENU.

5. The panel voice responds with Mas ter Code, pres s again

for next access code or DONE to select or CANCEL to
quit. Press the access code button again to hear the next

access code. When you hear the access code you wish
to change press the DONE Button.

6. Enter 4 new numbers using the red numbered keys.

1 - Panel Beeps On Off

2 - Panel Voice On Off

3 - Latchkey Time 12am - 11:59 pm Off

36 - Sensor Activated

12am - 11:59 pm Off

Light Lockout Start Time

(Not for use with Basic Model)

37- Sensor Activated Light

12am - 11:59 pm Off

Lockout Stop Time (Not for

use with Basic Model)

41 - Chime Voice On Off

42 - Speaker Volume
High/Low

Basic Model)

(Not for use wi th

High Low

43 - Pager Phone Number Up to 22 digits* Off

* See “Option 43 - Pager Phone Number” on page 9

11

System Tests & Trouble Beeps

Automatic Control Panel Testing--What the
System Tests for You

Your security system is able to automatically test itself for:

• Power failures

• Low batteries

• Non-working sensors

• Communication troubles with the Central Monitoring Sta­tion

Trouble Beeps. When your security system detects one

of the problems above, interior sirens sound trouble beeps
rapidly six times, and then again every minute, until the trouble
condition is corrected.

If you do a status check by pressing the SYSTEM STATUS
button twice or change the system from being armed to dis­armed or disarmed to armed, the beeps will stop. If the prob­lem is not corrected, beeps start again 4 hours later.

Silencing Trouble Beeps

Pressing the SYSTEM STATUS button twice or
changing from armed to disarmed or disarmed to
armed while the system has a trouble condition
stops the trouble beeps. Trouble beeps begin again
4 hours later, in some cases, unless the trouble
condition is corrected.

AC Power Failure. This condition occurs if your security

system has been accidentally unplugged or if there has been
an AC power outage. The backup battery will take over. If AC
power is not restored within 15 seconds, the Control Panel will
go dark and alert you with trouble beeps. If you press any but­ton, the display will light and pressing SYSTEM STATUS
twice will confirm the AC power failure. If AC power is not re­stored within 15 minutes, the system will call the central mon­itoring station (if programmed by installer). The backup
battery, if fully charged, will last for 18 - 24 hours with no AC
power.

call your security system dealer if the problem continues.

Sensor Low Battery. This condition occurs if a system

sensor has a low battery. The sensor may still be communicat­ing with the Control Panel. Trouble beeps will start and the

SYSTEM STATUS button will light. Press the SYSTEM STA-
TUS button twice to hear which sensor(s) have trouble. It may

be necessary for you to call your security system dealer to re­solve this problem. Some sensor batteries can be replaced by
the homeowner.

Fail-To-Communicate. This condition occurs if your se-

curity system cannot communicate to the central monitoring
station. Your system will try to report to the central monitoring
station 8 times before it tells you there is a Fail-To-Communi­cate problem. Trouble beeps will start and the SYSTEM STA-
TUS button will light. Press the SYSTEM STATUS button
twice to hear the trouble message. It may be necessary for
you to call your security system dealer if the problem contin­ues.

Sensor Open. This condition occurs if a door or window is

open, or a system sensor has been disturbed or tampered and
not reset properly. For example, a Motion Sensor may be off
the wall or a Door/Window Sensor cover may have been re­moved from the sensor. Your system will indicate this condi­tion to you by causing the SYSTEM STATUS button to light.
When you press this button twice, the system responds with

Sensor # Name open. Correct the problem by resetting the

sensor. If this condition continues call your security system
dealer

Option 50 Detected. The Control Panel receiver may

be experiencing some interference. The system will call to no­tify the central monitoring station about this problem.

Module 1 or 2 Failure. Call your security system deal-

er.

System Battery Failure. This condition occurs if the

emergency backup battery has been drained. Trouble beeps
will start and the SYSTEM STATUS button will light. Press the
SYSTEM STATUS button twice to hear the trouble message.
If your AC power is not working, your security system will shut
down once the battery is drained. The Control Panel battery
should be replaced once a year if using a 9V Ultralife battery.

Sensor Failure. This condition occurs if a sensor is not

communicating with the Control Panel. Trouble beeps will
start and the SYSTEM STATUS button will light. Press the
SYSTEM STATUS button twice to hear which sensor(s) have
trouble. Perform sensor tests. It may be necessary for you to

12

System Access Alarm. The Control Panel cover was

opened while the system was armed. The system will call the
central monitoring station to report a tamper alarm.

Clearing System Status

If a trouble condition is corrected, press the SYSTEM
STATUS button twice, listen to the status message, then

disarm the system to clear system status. If the trouble
condition was a low CPU battery, perform a sensor test.
The SYSTEM STATUS button should turn off if all trou-
ble conditions have been corrected.

Manual Tests--What You Need to Test

As an added safeguard, there are system tests you should do
yourself on a regular basis. The Control Panel cover in the
lower left corner reminds you to TEST WEEKLY.

Sensors

You can test sensors one at a time to make sure they are
sending strong signals to the Control Panel (see Testing Sen­sors paragraph).

Communication

You can also test the communication

between your system
and the Central Monitoring Station (see Testing Communica­tion paragraph).

Testing Sensors

You should test the security system at least once each week.

To perform the sensor test:

1. Open the Control Panel Cover.

2. Enter the master access code.

3. Press the Test button once, the Control Panel will say

Sensor Test.

4. Press the DONE button.

The panel will voice prompt you with a list of your programmed
sensors that you need to test. The panel will start with sensor

1 and say Test sensor 1, sensor name.

When you trip a sensor and it communicates successfully it
will be removed from the list. You may trip the sensors in any
order. The sensor test has a 4 minute time out that resets with
each sensor trip.

After all sensors have been successfully tested, the Control

Panel will say Sensor test complete, press DONE. Press
DONE. The Control Panel will say Sensor test ok.

If any of the sensors did not test successfully and you want to
terminate the test, press DONE. The Control Panel will say

Sensor test cancel ed or failure. If a sensor test fails, call your

security dealer.

Use the following table to trip sensors.

Sensor Trippi ng Instruct ions :

Sensor Do This

Door/Window Open the secured door or win-

dow

Freeze Apply ice to the sensor. Do not

allow the sensor to get wet

Water Press a wet rag or wet finger

over both of the round, gold­plated terminals on the underside
of the sensor

Carbon Monoxide
Alarm

Unplug the CO Alarm. Plug it
back in, then press the TEST/
RESET button until the unit
beeps 8 times

Sensor Tripping Instructions:

Sensor Do This

Glass Guard Tap the glass 3 or 4 inches from

the sensor

Motion Sensor Avoid the Motion Sensor’s view

for 5 minutes, then enter its view

Rate-of-Rise Heat
Detector

Rub your hands together until
warm, then place one hand on
the detector for 30 seconds

Shock Tap the glass twice, away from

the sensor. Wait at least 30 sec­onds before testing again

Smoke Press and hold the test button

until the system sounds trans­mission beeps

Panic Buttons Press and hold the appropriate

panic button(s) for 3 seconds

KeyChain Touch­pad

Press and hold LOCK and
UNLOCK simultaneously for 3
seconds

Remote Handheld
Touchpad and
Touchtalk 2-Way
RF Touchpad

for use with Basic Model)

(Not for use with

SWS

Basic Model)

(Not

Press and hold the 2 EMER­GENCY buttons simultaneously
for 3 seconds

Unplug the SWS, plug the unit
back in

Testing Communication

Test communication with your central monitoring station and
the pager at least once per week to make sure you have the
proper telephone connection between your system and the
central monitoring station.

To perform a phone test:

1. Open the Control Panel cover.

2. Enter the master access code.

3. Press the Test button twice, the Control Panel will say

Phone Test.

4. Press the DONE button.
The Control Panel will say Phone test is on twice. If the test is

successful the Control Panel will say Phone test ok within 3
minutes. The Control Panel will say Phone test is on three

times if you have a pager. Your pager will display 101 101 if
the phone test to the pager was successful. If the test is un­successful, the SYSTEM STATUS button will light and the

Control Panel will say Phone communication failure within 10

minutes. If a phone test fails, call your security system dealer.

NOTE: If your system is not connected to a central moni­toring station, and you don’t use a pager, you won’t be
able to perform the phone test.

13

Your Emergency Evacuation Floor Plan

Planning for Emergencies

This section describes what you can do to plan ahead for an
emergency:

• Emergency Planning

• Your Floor Plan

Emergency Planning

Since an emergency is always unexpected, you should devel­op plans to help prepare for a variety of emergency situations.
Periodically discuss and rehearse emergency plans to include
the following:

• Understand how to use your security system

• Know the normal state of doors and windows; open,

closed, or locked.

• Escape fast! (Do not stop to pack.)

• Use a different escape route if closed doors feel hot to

the touch.

• Crawl and hold your breath as much as possible to help

reduce smoke inhalation during your escape.

• Meet at a designated outdoor location.

• Emphasize that no one should return to the premises if
there is a fire.

• Notify the fire department from a neighbor’s phone.

• Emphasize that no one should enter the premises if they
hear sirens in the house.

• If you arrive at the premises and hear sirens, do not
enter. Call for emergency assistance from a neighbor’s
phone.

Your Floor Plan

Use the following guidelines when drawing your floor plan:

• Show all building levels.

• Show exits from each room (two exits per room are rec­ommended).

• Show the location of all security system components.

• Show the location of any fire extinguishers.

14

Alarm System Limitations

Not even the most advanced alarm system can guarantee protection against burglary, fire, or environmental problems.

All alarm systems are subject to possible compromise or failure-to-warn for a variety of reasons.

• If sirens are not placed within hearing range of persons sleeping or in remote parts of the premises, or if they are placed
behind doors or other obstacles.

• If intruders gain access through unprotected points of entry or areas where sensors have been bypassed.

• If intruders have the technical means of bypassing, jamming, or disconnecting all or part of the system.

• If power to sensors is inadequate or disconnected.

• If freeze or any environmental sensors are not located in areas where the appropriate condition can be detected.

• If smoke does not reach a Smoke Sensor. For example, Smoke Sensors cannot detect smoke in chimneys, walls, roofs, or
smoke blocked by a closed door. Sensors may not detect smoke in other levels of the building. Sensors may not warn in
time when fires are caused by smoking in bed, explosions, improper storage of flammables, overloaded electrical circuits,
or other hazardous conditions.

• If telephone lines are out of service. Telephone lines are also vulnerable to compromise by any of several means.

Inadequate maintenance is the most common cause of alarm failure. Therefore, test your system at least once per week to be
sure sensors, sirens, and phone communications are all working correctly.

Although having an alarm system may make you eligible for reduced insurance premiums, the system is no substitute for insur­ance.

WARNING! Security system devices cannot compensate you for the loss of life or property.

Service

If you have any questions about your security system or if you ever need service, please contact your security consultant.

Company Name _____________________

Phone Number _____________________

Address _____________________

_____________________

15

Numerics
2-Way Voice Audio Session 9
2-Way Voice On-Board 4
A
AC Power Failure 11, 14
AC Power Restoral 11
Access Code, change 13
Access Code, delete 13
Access Codes 11
Alarm 6
Alarm Sirens and Lights 6
Alarm System Limitations 19
Alarm Type 6
Alarms 11
ARM Doors/Windows 5, 7, 9, 10
ARM Doors/Windows & Motion Sensors 5, 9
ARM Doors/Windows with No Entry Delay 9
ARM Doors/Windows with No Entry Delay and Motions
with Latchkey 9
ARM Motion Sensors 5, 7, 9, 10
ARM Motions with Latchkey 9
Arm with Doors or Windows Open 3
Arming 11
audio session 9
Audio Verification Module 4
Audio Verification Set 9
B
battery failure 14
Beeps 5, 14
C
Canceling Accidental Alarms 3
Change an Access Code 13
CHIME Doors 5, 8
CHIME Special Motion 5, 8
Clearing System Status 14
CODE 7
Communication test 15
Control Panel 4
D
delay, entry 5
delay, exit 5
Delete an Access Code 13
DISARM 5, 7, 9, 10
Disarm 11
Door/Window Sensors 4
E
Emergency 6, 8, 10
Emergency Evacuation Floor Plan 18
Entry delay 5
Entry/Exit Activated Lights 11
Exit delay 5
F
Fail to Arm 6, 11
Fail to Disarm 6, 11
Fail-To-Communicate 14
Fire (Temporal 3) 6

H
HOME CONTROL 8
HOME SECURITY 7
House Code 11
I
Indoor Motion Sensors 4
Intrusion 6
K
KeyChain Touchpad 10
KeyChain Touchpads 4
L
Latchkey 7, 9, 11
Light 10
Light button 10
Light Lockout 11
LIGHT ON/OFF 10
light unit number 10
light unit numbers 4
lights on/off 7
LIGHTS Sensor Activated 8, 11
LIGHTS Time Activated 8
Lights Time Activated 11
limitations 19
LOCK 10
M
Master Access Code default 5
Messages to the Owner 3
messages, trouble 14
Module 1 or 2 Failure 14
Modules 4
motion sensors 4, 5, 6, 7, 9
N
No activity 11
No Activity Beeps 5
No Entry Delay 7
O
Option 01 - Panel Beeps 11
Option 02 - Panel Voice 11
Option 03 - Latchkey Time 11
Option 36 - Sensor Activated Light Lockout Start Time
11
Option 37 - Motion Activated Light Lockout Stop Time
11
Option 41 - Voice Chime 11
Option 42 - Speaker Level 11
Option 43 - Pager Phone Number 11
Option 50 Detected. 14
Option Table 13
Outdoor Motion Sensors 4
P
pager 6
pager reports 6, 11
Panel Beeps 5
Panel Indicator Lights 6
Panel Voice Messages 5
panic code 3
Phone Commands for Remote Access 9

1

Phone Test 11, 15
Programming Decals 12
Programming Instructions 13
R
Remote Access 9
Remote Handheld Touchpad 10
Remote Handheld Touchpad and Touchtalk 2-Way RF
Touchpad 4
Reports, pager 6
S
Sensor Activated Lights 8, 11
Sensor Failure 14
Sensor Low Battery 14
Sensor Open 14
Sensor Test 11
sensor testing 15
Sensor Tripping Instructions 15
Sensors 4, 15
Service 19
Set Clock 11
Silencing Trouble Beeps 14
Sirens 6
Smoke Sensors 4
STAR 10
subdisarm 3, 7
System Access Alarm 14
System Battery Failure 14
SYSTEM STATUS 6, 7, 10, 14
System Status 9
SYSTEM STATUS, clearing 14
System Tests 14, 15
T
Table Alarm Type 6
Table Audio Verification Set 9
Table Numeric Pager 6
TABLE OF CONTENTS 3
Table Options 13
Table Panel Beeps 5
Table Panel Indicator Lights 6
Table Phone Commands for Remote Access 9
Table Sensor Tripping Instructions 15
test phone 15
Testing Communication 15
Testing Sensors 11, 15
Time Activated Lights 8, 11
Toggle Lights 9
touchpads 10
Touchtalk 2-Way RF Touchpad 10
Trouble Beeps 5, 14
trouble beeps, silencing 14
Trouble Messages 14
U
unit numbers 4
UNLOCK 10

2

3

4

Lights off

SYSTEM

STATUS

+

9 – 0

on special lights

Toggle lights

Lights on

SYSTEM

STATUS

+

7 – 8

Set lights to time activated

Set lights to sensor activated

Open a garage door or turn

Time

Activated

LIGHTS

Sensor

Activated

Set Special Motion Chime

LIGHTS

CHIME

Special

Motion

Set doors to Chime

CHIME

DOORS

Send an alarm to the

Central Monitoring Station

Check the system status

EMERGENCY

SYSTEM

STATUS

Press Twice or

Press & hold

for 3 seconds

Press Twice

Activate the Latchkey feature

Disarm the system

Subdisarm the system

Master Code

Sensors

Motion

DISARM

+ Access Code

Press Twice

ARM

Arm the system

– Motion Sensors

Arm the system

– Doors/Windows & Motion Sensors

Activate No Entry Delay

Windows

Doors &

ARM

Sensors

Motion

ARM

ARM

Sensors

Motion

ARM

Windows

Doors &

Press Twice

Arm the system

– Doors & Windows

How to . . .

Windows

Doors &

ARM

CONTROL PANEL

Press Twice

Press Twice

Press & hold

Press + Master Code + 0

*

Master Code

SYSTEM

STATUS

Press both EMERGENCY buttons.

+ Unit #

Press & hold for 3 seconds.

Press Once

DISARM

+ Access Code

Sensors

Motion

ARM

Press Twice

Windows

Doors &

ARM

Press Twice

Windows

Doors &

ARM

Sensors

Motion

ARM

Sensors

Motion

ARM

Windows

Doors &

ARM

Touchtalk 2-Way RF

TOUCHPAD

Quick Reference Table

REMOTE HANDHELD &

KEYCHAIN TOUCHPAD

Press & hold

*

Press + Master Code + + 1

for 3 seconds

*

Press + Master Code + 1

*

Press + Master Code + 1

Press 3 times

Press + Master Code + 3 + 3

*

Press once if

programmed

Press + Master Code + 2 + 2

*

Press twice

Press + Master Code + 2 + 3

*

*

Press + Master Code + 3

*

Press + Master Code + 2

REMOTE PHONE CONTROL

466-1575 Rev. D

#