Interlogix IS-ZW-AM-1 User Manual

GE

Security

IS-ZW-AM-1 Appliance Module
Installation Sheet

Description

Z-Wave technology is designed to automate lighting/home control
and provides easy remote operation of all your Z-Wave enabled
devices. The GE Z-Wave family includes a variety of devices to
control lighting in your home.

This module is one device of a Z-Wave control system and is
designed to work with all other Z-Wave enabled devices in a home
control network. It will also act as a wireless repeater to ensure
that commands intended for another device in the network are
received, thereby extending the range of the wireless controller. Z­Wave devices of other types can be added to the system and will
act as range extenders if they support this function of repeating
the signal received to other nodes in the system.

Note: This document assumes you have a remote control to enroll

the unit into your system. This document does not include
instructions on how to use an optional web portal to enroll the
unit. If you have a web-enabled system, contact GE Security.

Key features

• One Z-Wave controlled AC outlet. Remote on/off control via
the Z-Wave remote control. Manual on/off control with the
module pushbutton.

• One always-on pass-through AC outlet.

• Space efficient design does not block the lower outlet when
plugged in to the upper outlet of a duplex wall receptacle (this
assumes that the duplex receptacle is mounted with the
ground pin down). Plugs and cords for connected devices
route to the side allowing close placement of furniture.

• Grounded 3-wire power connection for safety.

Note: There are no user serviceable parts in this unit.

To reduce the risk of electric shock, this product has a grounding
type plug that has a third (grounding) pin. This plug will only fit into
a grounding type power outlet.

Caution: If the plug does not fit into the outlet, contact a qualifed

electrician to install the proper outlet. Do not change the plug in
any way.

Installation

The device plugged into the Z-Wave controller outlet on this
module must not exceed 600 W (incandescent); 1800 W (15A)
Resistive or ½ HP Motor. Total load capacity for both outlets is
1800 W (15 A) Resistive.

WARNING: Due to risk of fire, electrical shock and burns, exercise

extreme caution when using Z-Wave devices to control
appliances. Operation of the Z-Wave device may be in a different
room than the controlled appliance, also an unintentional
activation may occur if the wrong button on the remote is
pressed. Z-Wave devices may automatically be powered on due to
timed event programming. Depending upon the appliance, these
unattended or unintentional operations could possibly result in a
hazardous condition. For these reasons, we recommend the
following installation guidelines.

Installation guidelines

• Assign Z-Wave controlled appliances to device numbers 10 to
18 on the remote control. The likelihood of unintentionally
turning on the appliance will be reduced significantly because
the Shift button will need to be pressed before pressing
device numbers 10 to 18.

• Z-Wave devices controlling appliances should be removed
from the “All” control setting. Refer to the documentation
provided with the remote control.

• Do not include Z-Wave devices in groups or scenes if they
control appliances.

• Do not use Z-Wave devices to control electric heaters or any
other appliances, which may present a hazardous condition
due to unattended, unintentional, or automatic power on
control.

• Double check programming for accuracy before using the
module.

Caution: Not for use with medical or life support equipment.

Z-Wave enabled devices should never be used to supply power to,
or control the on/off status of medical and/or life support
equipment.

© 2009 GE Security, Inc.

P/N 1069503 • REV A • ISS 16NOV09

1 of 4

Wireless range

This device complies with the Z-Wave standard of open-air, line of
sight transmission distances of 65 feet. Actual performance in a
home depends on the number of walls between the remote
control and the destination device, the type of construction, and
the number of Z-Wave enabled devices installed in the control
network.

Z-Wave network

Every Z-Wave enabled device acts as a signal repeater and
multiple devices result in more possible transmission routes, which
help eliminate “RF dead spots”.

RF range guidelines

• Each wall or obstacle (such as a refrigerator or big screen TV)
between the remote control or a Z-Wave device and the
destination device will reduce the maximum range by
approximately 25 to 30 percent.

• Brick, tile, or concrete walls block more of the RF signal than
walls made of wooden studs and plasterboard (drywall).

• Wall-mounted Z-Wave devices installed in metal junction
boxes will suffer a significant loss of range (approximately 20
percent) since the metal box blocks a large part of the RF
signal.

• Z-Wave home control networks are designed to work
properly alongside 802.11 wireless computer networks,
Bluetooth and other 2.4GHz or 5.8GHz devices. Some baby
cams, wireless video devices and older cordless phones using
the 900MHz frequency range may cause interference and
limit Z-Wave functionality. Many 900 MHz products have a
switch to select channel A or B. You may find that one of
these channels will cause less interference than the other
channel.

Advanced operation

All-on/all-off commands

The module can be set to respond to all-on and all-off commands
in up to four different ways. Refer to the remote control
documentation for information on how to change this setting.

The four possible responses are:

• It will respond to all-on and the all-off commands (default).

• It will not respond to all-on or all-off commands.

• It will respond to the all-off command but will not respond to
the all-on command.

• It will respond to the all-on command but will not respond to
the all-off command.

Restoring factory defaults

All configuration parameters can be restored to their factory
default settings by using the remote control to reset the device
(delete it from the network).

Over-current protection

Over-current protection is provided by an internal fuse, which is
not user serviceable. Check the home’s circuit breakers before
concluding that the product must be replaced.

Interoperability with Z-Wave devices

A Z-Wave network can integrate devices of various classes.
Although every Z-wave certified product is designed to work with
all other Z-Wave certified products, the remote control includes
the appropriate device classifications in order to control non­lighting Z-Wave devices.

Basic operation

Remote control

GE Z-Wave remote controls provide control of an individual device,
groups of devices, and scenes. Refer to the documentation
provided with the remote control for details on its capabilities and
instructions for adding and controlling devices.

When prompted by the remote control, tap the module
pushbutton. The remote control should indicate that the action
was successful. If the remote control indicates the action was
unsuccessful, repeat the procedure.

Once the module is part of the network, the same basic procedure
is used to add the module to groups or scenes. Refer to the
remote control documentation for details.

Manual control

The module pushbutton allows you to manually turn the
connected equipment on or off by pressing the button. This is a
toggle switch; if the device is off, pressing the button turns the
device on and vice versa.

Note: After a power failure, the module returns to its last used

on/off state.

Specifications

Power 120 VAC, 60 Hz

Signal (frequency) 908.42 MHz

Maximum load for both outlets 15A, 1800W Resistive

Maximum load for the Z-Wave
controlled outlet

Range Up to 100 feet line of sight between

Operating temperature 32 to 104ºF (0 to 40ºC)

For indoor use only

600 W Incandescent, ½ HP Motor or
1800 W Resistive

the wireless controller and the
closest Z-Wave receiver module

FCC

The Federal Communication Commission Radio Frequency
Interference Statement includes the following paragraph:

The equipment has been tested and found to comply with the
limits for a Class B Digital Device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This

2 of 4 P/N 1069503 • REV A • ISS 16NOV09