Interlogix IFS ANT-OMN-15DB-2G Quick Start Manual
IFS ANT-OMN-15DB-2G Quick Start Guide
Specifications
Content
Package Contents 1
Installation Steps 1
Specifications 1
Contact information 2
This is the IFS ANT-OMN-15DB-2G Quick Start Guide. This
document provides basic instructi ons for inst all ing and us ing
the IFS ANT- OMN-15DB-2G.
Package Contents
Thank you for purchasing the IFS ANT- OMN-15DB-2G.
Open the box of the IFS ANT- OMN-15DB-2G and carefully
unpack it. The box should contain the following items:
• ANT- OMN-15DB-2G x 1
• Screw Package x 1
If any item is found missing or damaged, please contact your
local reseller for replacement.
Installation Steps
• Frequency: 2400 ~ 2500MHz
• Max Gain: 15dBi
• VSWR: <= 1.3
• Connector: N-type female
• Wave impedance: 50 ohm
• Weight: 1050g
• Vertical beam width degree: 10
• Mounting Type: Mast mount
OUTDOOR INSTALLATION WARNING
IMPORTANT SAFETY PRECAUTIONS:
LIVES MAY BE AT RISK!
these instructions and any special instructions that
are included with the equipment you are installing.
Carefully observe
CONTACTING POWER LINES CAN BE LETHAL
Make sure no power lines are
anywhere where possible
contact can be made. Avoid
contact with antennas, masts,
towers, guy wires or cables
that may lean or fall. You may
be injured or killed if you are
touching or holding any part of
equipment that comes in
contacts with
Make sure that equipment or personnel must not come in
contact directly or indirectly with power lines.
electrical lines.
Assuming all overhead lines are power lines:
The horizontal distance from a tower, mast or antenna to the
nearest power line should be at least twice the total length of
the mast/antenna combination. This will ensure that the mast
will not contact power if it falls either during installation or later.
TO AVOID FALLING, USE SAFE PROCEDURES
WHEN WORKING AT HEIGHTS ABOVE GROUND
Select equipment locations that will allow safe, simple
P/N 1073058 • REV A • 16OCT15 1
equipment installation.
Don’t work alone. A friend or co-worker can save your life if
an accident happens.
Use approved non-conduc ting las ers and other safety
equipment. Make sure all equipment is in good repair.
If a tower or mast begins falling, don’t attempt to catch it.
Stand back and let it fall.
If anything such as a wire or mast does come in contact
with a power line, DON’T TOUCH IT OR ATTEMPT TO MOVE
IT. Instead, save your life by calling the power company.
Don’t attempt to erect antennas or towers on windy days.
MAKE SURE ALL TOWERS AND MASTS ARE
SECURELY GROUNDED, AND ELECTRICAL
CABLES CONNECTED TO ANTENNAS HAVE
LIGHTNING ARRESTORS.
This will help prevent fire damage or human injury in case of
lightning, static build-up, or short circuit within equipment
connected to the antenna.
The base of the antenna mast or tower must be connected
directly to the building protective ground or to one or more
approved grounding rods, using 1 OAWG ground wire and
corrosion-resistant connectors.
Refer to the National Electrical Code for grounding details.
IF A PERSON COMES IN CONTACT WITH
ELECTRICAL POWER, AND CANNOT MOVE:
DON’T TOUCH THAT PERSON, OR YOU MAY BE
ELECTROCUTED.
Use a non-conductive dry board, stick or rope to push or
drag them so they no longer are in contact with electrical
power.
Once they are no longer contacting electrical power,
administer CPR if you are certified, and make sure that em ergency medical aid has been requested.
Contact information
www.interlogix.com or www.utcfssecurityproducts.eu.
For customer support, see www.interlogix.com/customer-
support .
© 2015 United Technologies Corporation
Interlogix is part of UTC Climate Controls & Security, a unit of
United Technologies Corporation. All rights reserved.
2 IFS ANT-OMN-15DB-2G Quick Start Guide
Loading...