Interlogix ES2001-4P-4T User Manual
IFS ES2001-4P-4T User Manual
P/N 1072680 • REV A • ISS 22OCT13
r
r
Copyright © 2013 United Technologies Corporation
Interlogix is part of UTC Climate Controls & Security, a unit of United
Technologies Corporation. All rights reserved.
Trademarks and
patents
The IFS ES2001-4P-4T name and logo are trademarks of United
Technologies.
Other trade names used in this document may be trademarks or
registered trademarks of the manufacturers or vendors of the
respective products.
Manufacture
Interlogix
3211 Progress Drive, Lincolnton, NC 28092 USA
Authorized EU manufacturing representative:
UTC Climate Controls & Security B.V.,
Kelvinstraat 7, 6003 DH Weert, Netherlands
Intended use
Use this product only for the purpose it was designed for; refer to the
data sheet and user documentation for details. For the latest product
information, contact your local supplier or visit us online at
www.interlogix.com.
Certification
N4131
FCC compliance
This equipment has been tested and found to comply with the limits fo
a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications.
You are cautioned that any changes or modifications not expressly
approved by the party responsible for compliance could void the
user's authority to operate the equipment.
ACMA compliance Notice! This is a Class A product. In a domestic environment this
product may cause radio interference in which case the user may be
required to take adequate measures.
Canada
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme á la norme
NMB-003du Canada.
European Union
directives
2004/108/EC (EMC Directive): Hereby, UTC Climate Controls &
Security Corporation, Inc. declares that this device is in compliance
with the essential requirements and other relevant provisions of
Directive 2004/108/EC.
Contact Information For contact information, see www.interlogix.com
www.utcfssecurityproducts.eu
.
or
IFS ES2001-4P-4T User Manual
TABLE OF CONTENTS
IFS ES2001-4P-4T USER MANUAL ................................................................................1
1. INTRODUCTION
1.1 Checklist ...............................................................................................................................................5
1.2 Features ................................................................................................................................................5
1.3 Specification.............................................................................................................. ...........................6
..........................................................................................................5
2. HARDWARE DESCRIPTION.......................................................................................7
2.1 Product Description.............................................................................................................................7
2.2 Front Panel ...........................................................................................................................................7
2.2.1 LED indicators ............................................................................................................................. 8
2.3 Rear Panel.............................................................................................................................................8
2.4 Hardware Installation...........................................................................................................................9
2.4.1 Before start up ............................................................................................................................. 9
2.5 Desktop Installation.............................................................................................................................9
2.6 Rack Mounting .................................................................................................................................. 10
2.7 Product Application.......................................................................................................................... 11
2.7.1 Connecting end node or switch ................................................................................................. 11
2.7.2 Typical Uses: ............................................................................................................................. 13
2.8 Examples of Power over Ethernet Powered Device...................................................................... 14
3. SWITCH OPERATION................................................................................................15
3.1 Address Table ................................................................................................................................... 15
3.2 Learning............................................................................................................................................. 15
3.3 Forwarding & Filtering...................................................................................................................... 15
3.4 Store-and-Forward............................................................................................................................ 15
3.5 Auto-Negotiation............................................................................................................................... 15
4. POWER OVER ETHERNET OVERVIEW
5. THE POE PROVISION PROCESS
Stages of powering up a PoE link....................................................................................................... 18
5.1 Line Detection ................................................................................................................................... 18
5.2 Classification..................................................................................................................................... 18
5.3 Start-up............................................................................................................................................... 18
5.4 Operation ........................................................................................................................................... 19
5.5 Power Disconnection Scenarios..................................................................................................... 19
.............................................................................18
...................................................................16
6.TROUBLESHOOTING.................................................................................................20
APPENDIX A NETWORKING CONNECTION
...............................................................21
3
IFS ES2001-4P-4T User Manual
A.1 DATA OUT PoE Switch RJ-45 Port Pin Assignments (Port 1 to Port-4)..................................... 21
A.2 Switch‘s RJ-45 Pin Assignments (Port-5 to Port-8)...................................................................... 21
A.3 RJ-45 cable pin assignment............................................................................................................ 22
CONTACTING TECHNICAL SUPPORT........................................................................23
4
IFS ES2001-4P-4T User Manual
1. Introduction
1.1 Checklist
Check the contents of your package for following parts:
ES2001-4P-4T
User's manual CD x1
Power cord x 1
If any of these pieces are missing or damaged, please contact your dealer immediately. If possible, retain the carton including the original
packing material, to repack the product in case there is a need to return it to us for repair.
1.2 Features
◆ 8-Port 10/100Mbps Fast Ethernet ports
◆ 4-Port supports 48VDC power to PoE Powered device
◆ Hardware based 10/100Mbps auto-negotiation
◆ Flow control for full duplex operation and back pressure for half duplex operation
◆ Integrates address look-up engine, supports 1K absolute MAC addresses
◆ Automatic address learning and address aging
◆ Supports Auto MDI/MDI-X function
◆ LED indicators for easy network diagnostic
◆ Ethernet standards comply with IEEE 802.3 Ethernet, IEEE 802.3u Fast Ethernet, IEEE 802.3x Flow Control and
IEEE 802.3af Power over Ethernet
◆ Optional Rack Ear Accessories Kit for 10-inch cabinet (RKE-10A) and 19-inch cabinet (RKE-10B)
◆ EMI standards comply with FCC, CE class A
5
1.3 Specification
Model ES2001-4P-4T
Hardware Specification
Network Connector 8-Port RJ-45 for 10/100Base-TX
PoE Inject Port 4-Port with PoE injector function, Port-1 to Port-4
One power,
LED Display
Switch Architecture Store and Forward switch architecture
Switch Fabric 1.6Gbps
MAC Address 1K MAC address table with Auto learning function
Throughput 1.19Mbps
Remote power feeding
1-4 port PoE in-use, LNK/ACT
5-8 port LNK/ACT
End-point insert type and compatible with IEEE 802.3af
Per port feeding power: 48V DC, 15.4W, 350mA (Maximum)
(Pin 1, 2, 3, 6)
IFS ES2001-4P-4T User Manual
Power AC 100~240V, 50/60Hz,
Power Consumption Max. 65 watts / 221 BTU
Dimension (W x D x H) 217 x 135 x 43 mm
Weight 1.0 kg
Power over Ethernet
PoE Standard IEEE 802.3af Power over Ethernet / PSE
PoE Power Supply Type End-Span
PoE Power Output Per Port 48V DC, 350mA . Max. 15.4 watts
Power Pin Assignment 1/2(+), 3/6(-)
Power Budget
Standard Conformance
EMI Safety FCC Class A, CE
Operating environment 0~50 degree C, 10%~95%RH
Storage environment -40 ~70 degree C, 95% RH
Operating Humidity
55 watts
5% to 90% , relative humidity, non-condensing
Storage Humidity
Standard Compliance IEEE 802.3
5% to 90% , relative humidity, non-condensing
IEEE 802.3u
IEEE 802.3x
IEEE 802.3af
Ethernet
Fast Ethernet
Flow Control
Power over Ethernet
6
IFS ES2001-4P-4T User Manual
2. Hardware description
This product operates at two different running speeds – 10Mbps or 100Mbps. The switch automatically distinguishes the
speed of incoming connection.
This section describes the hardware features of ES2001-4P-4T. For easier management and control of the Switch, familiarize
yourself with its display indicators, and ports. Front panel illustrations in this chapter display the unit LED indicators. Before
connecting any network device to the ES2001-4P-4T, please read this chapter carefully.
In the following section, the term “Switch” means the Switch device, i.e. ES2001-4P-4T; the term “switch” can be any third
party switches
2.1 Product Description
The ES2001-4P-4T is equipped with unshielded twisted-pair (UTP) cable ports providing dedicated 10 or 100Mbps bandwidth.
The ES2001-4P-4T supports MDI/ MDI-X for auto sensing the use of either CAT5 ‘patch’ or CAT5 ‘crossover’ cables on each of
the 8 x 10/100Mbps ports. The Switch also provides PoE injection function on ports #1, 2, 3, 4, which is able to drive 4 x IEEE
802.3af compliant powered devices. Each 10/100Mbps port can supports up to 200Mbps of throughput in full-duplex mode,
the ES2001-4P-4T also provides a simple, cost-effective, and highly reliable network connection for data as well as power.
Furthermore, it is the ideal device for bridging among Ethernet, Fast Ethernet workgroups and networks.
With 4 PoE interfaces, the ES2001-4P-4T is ideal for small business and workgroups requiring to deploy the PoE for the
wireless access points, IP-based surveillance camera or IP phones in any places easily, efficiently and cost effective.
The front panel of ES2001-4P-4T provides LEDs for easy recognition of the switch operation status and troubleshooting. These
LED indicators display the power status for the system, LNK/ACT and speed for each10/100M port. Also the PoE in use LED
indicates for PoE ports (port#1 to port#4).
With data and power over Ethernet from one unit, the ES2001-4P-4T reduces the need for additional cables and eliminates the
need for dedicated electrical outlets on the wall, ceiling or any unreachable place. The CAT5 cable carries both data and
power lowering the installation costs, simplifying the installation effort and eliminating the need for electricians or extension
cords.
2.2 Front Panel
The Front Panel of the ES2001-4P-4T PoE Ethernet Switch consists of 8x Auto-Sensing 10/100Mbps Ethernet RJ-45 Ports. The
LED Indicators are also located on the front panel of the ES2001-4P-4T.
Figure 2-1 ES2001-4P-4T Switch front panel
7
Loading...