Interlogix D9100E User Manual

D9110

D9110E
D9110-R3
D9120
D9120-R3
D9130
D9130-R3

D9110E-R3

D9120E

D9120E-R3

D9130E

D9130E-R3

IFS Fiber Module
Installation & Operation
Instructions

P/N 1062846 • REV B • ISS 01AUG11

D9100 SERIES

RS - 232 DATA

(DTE)

12
13
14
15
16

1
2
3
4
5
6
7

Data Output
Data Input

Ground

RS - 232 DATA

(DCE)

RS - 422 DATA

12
13
14
15
16

10
11
12
13
14
15
16
17
18
19
20

1
2
3
4
5
6
7

9

Data Input
Data Output

Ground

+ Data Input

- Data Input

- Data Output
+ Data Output

CONTROL

LINES

10
20
21

1
2
3
4
5
6
7
8
9

Ground

RTS
CTS
DSR

DCD
+5 VDC

DTR

D9100 SERIES

A/B SWITCH

POSITION A

A/B SWITCH

POSITION B

4
3
2
1

4
3
2
1

Ground
Data Out
Ground
Data In

Ground
Data In
Ground
Data Out

2

1

Master/Slave/Bus

2

1

Slave Bus

2

Master

1

Note: The MASTER / SLAVE / BUS switch is functional only

on the D9100 Series units, not the D9100E Series units.

2

1

REPEATER CONFIGURATION

INDICATORS

REC A

CTS
RTS

XTMR A

POWER

FAIL

RECEIVE A

TRANSMIT A

RESET

Duplex single mode
fiber optic cable

Duplex single mode
fiber optic cable

RS232 OPTICAL TRANSCEIVER

ifs

INDICATORS

REC A

CTS
RTS

XTMR A

POWER

REC B

XTMR B

FAIL

D9130E

International
Fiber
Systems
Incorporated

RECEIVE A

TRANSMIT A

RECEIVE B

TRANSMIT B

RESET

SLAVE
MASTER
BUS

A

B

RS232

CONNECTOR

CHASSIS GRD  - 1

DTE

DATA IN  - 2
DATA OUT  - 3

SW2

RTS  - 4

DCE

CTS  - 5
DATA GRD  - 7

ON
OFF
OFF
#2

POWER

DSR  - 6
DCD  - 8
DTR  - 20

A B

+ 12 VDC - 1

D9130

SLAVE
MASTER
BUS

International
Fiber
Systems
Incorporated

ON
ON
OFF
#1

RS232 OPTICAL TRANSCEIVER

ifs

- 2

Black wire
Black with white stripe

RS232

CONNECTOR

CHASSIS GRD  - 1
DATA IN  - 2

DTE

DATA OUT  - 3
RTS  - 4

SW2

CTS  - 5

DCE

DATA GRD  - 7
DSR  - 6

ON
OFF
OFF
#2

POWER

DCD  - 8
DTR  - 20

A B

+ 12 VDC - 1

- 2

Black wire
Black with white stripe

ON
ON
OFF
#1

}

To next D9130E/D9130

series module

INDICATORS

REC A

CTS
RTS

XTMR A

POWER

REC B

XTMR B

FAIL

RECEIVE A

TRANSMIT A

RECEIVE B

TRANSMIT B

RESET

Duplex single mode
fiber optic cable

RS232 OPTICAL TRANSCEIVER

A

B

ifs

D9130

International
Fiber
Systems
Incorporated

SLAVE
MASTER
BUS

ON
ON
OFF
#1

DTE

DCE

ON
OFF
OFF
#2

SW2

POWER

RS232

CONNECTOR

CHASSIS GRD  - 1
DATA IN  - 2
DATA OUT  - 3
RTS  - 4
CTS  - 5
DATA GRD  - 7
DSR  - 6
DCD  - 8
DTR  - 20

A B

+ 12 VDC - 1

- 2

Black wire
Black with white stripe

POINT - TO - POINT CONFIGURATION

INDICATORS

REC A

CTS
RTS

XTMR A

POWER

FAIL

Duplex single mode
fiber optic cable

RECEIVE A

TRANSMIT A

RESET

RS232 OPTICAL TRANSCEIVER

ifs

D9130E

SLAVE
MASTER
BUS

International
Fiber
Systems
Incorporated

ON
ON
OFF
#1

DTE

SW2

DCE

ON
OFF
OFF
#2

A B

POWER

RS232

CONNECTOR

CHASSIS GRD - 1
DATA IN  - 2
DATA OUT  - 3
RTS  - 4
CTS  - 5
DATA GRD  - 7
DSR  - 6
DCD  - 8
DTR  - 20

+ 12 VDC - 1

- 2

Black wire
Black with white stripe

INDICATORS

REC A

CTS
RTS

XTMR A

POWER

FAIL

RECEIVE A

TRANSMIT A

RESET

RS232 OPTICAL TRANSCEIVER

ifs

D9130E

SLAVE
MASTER
BUS

International
Fiber
Systems
Incorporated

ON
ON
OFF
#1

DTE

SW2

DCE

ON
OFF
OFF
#2

A B

POWER

RS232

CONNECTOR

CHASSIS GRD - 1
DATA IN  - 2
DATA OUT  - 3
RTS  - 4
CTS  - 5
DATA GRD  - 7
DSR  - 6
DCD  - 8
DTR  - 20

+ 12 VDC - 1

- 2

Black wire
Black with white stripe

D9100

NOTE: WITHOUT PROPER FIBER CONNECTION, LED's DO NOT INDICATE
CORRECT OPERATIONAL STATUS OF THE UNIT.

A

F

G

H

B

I

ACData Receive Channel A
B

Data Transmit Channel A
Data Receive Channel B

D

Data Transmit Channel B

C

D

E

M

L

K

J

E

Reset Switch

F

Receive Channel A
CTS (Clear To Send)

G

RTS (Request To Send)

H

I

Transmit Channel A

J

Power
Receive Channel B

K

Transmit Channel B

L

M

Fail

LED illuminates
LED illuminates
LED illuminates

LED illuminates

LED illuminates

LED illuminates

LED illuminates

LED illuminates

A

NOTE: WITHOUT PROPER FIBER CONNECTION, LED's DO NOT INDICATE
CORRECT OPERATIONAL STATUS OF THE UNIT.

D9100E

B

C

D

E

F

G

ACData Receive
B

Data Transmit
Reset Switch

D

Receive

E

CTS (Clear To Send)

F

RTS (Request To Send)

G

Transmit

Power

H

I

H

LED illuminates

LED illuminates
LED illuminates
LED illuminates
LED illuminates

I

Fail

LED illuminates

FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesirable operation.

Changes or modifications not expressly approved by International Fiber Systems, Inc. could void
the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to cor­rect the

interference at his own expense.

CLASS 1 LASER PRODUCT

(For purposes of IEC 60825-1)

Complies with FDA Performance Standard for Laser Products

Title 21

Code of Federal Regulations

Subchapter J

Comprehensive
Lifetime Warranty

(a) Seller warrants to the original End User that products and any
services furnished hereunder will be free from defects in material
and workmanship as of the date of delivery, and will conform to
Seller’s published technical specications. The foregoing shall
apply only to failures to meet said warranties which appear within
that period of time during which the Products are installed in their
original installation for the original End User and operator of such
Products; provided, however, that in the event of product discontin­uance, warranty support is limited to ve (5) years from the
announcement of discontinuance. Notwithstanding the preceding
sentence, the duration of the warranty period for
manufactured by Seller (e.g., ber optic cabling, test equipment,
power supplies or batteries) shall be the warranty period oered by
the original manufacturer, if any.

(b) The conditions of any tests shall be mutually agreed upon and
Seller shall be notied of, and may be represented at, all tests that
may be made. The warranties and remedies set forth herein are
conditioned upon (a) proper storage, installation, use and mainte­nance, and conformance with
Seller and (b) Buyer promptly notifying Seller of any defects and,
if required, promptly making the product available for correction.

(c) If any product or service fails to meet the foregoing warranties,
Seller shall thereupon correct any such failure either at its option,

any applicable recommendations of

products not

(i) by repairing any defective or damaged product or parts of the
products, or (ii) by making available any necessary repaired or
replacement products or parts thereof. Any repaired or replacement
part or product shall be warranted for the remaining period of the
original Warranty Period. Seller shall pay, or credit Buyer for, the
cost of freight for all return shipments of products or parts to
Buyer. Where a failure cannot be corrected by Seller's reasonable
eorts, the parties will negotiate an equitable adjustment in price.

(d) The preceding paragraph sets forth the exclusive remedies for
claims based on defect in or failure of products or services,
whether the claim is in contract, indemnity, warranty, tort
(including Seller's negligence), strict liability or otherwise and
however instituted. Upon the expiration of the warranty period,

liability shall terminate and BUYER shall have a reason-

all such
able time, within thirty days after the warranty period, to give
written notice of any defects which appeared during the warranty
period. The foregoing warranties are exclusive and in lieu of all
other warranties, whether written, oral, implied or statutory.
NO IMPLIED OR STATUTORY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR PARTICULAR
PURPOSE SHALL APPLY. Seller does not warrant any
products or services of others which BUYER has designated.

Contacting us

For help installing, operating, maintaining, and troubleshooting this product, refer to this document and any
other documentation provided. If you still have questions, contact us during business hours (Monday through
Friday, excluding holidays, between 5 a.m. and 5 p.m. Pacific Time).

Sales and support contact information

North
America

Toll-free: 855.286.8889 in the US, including Alaska and Hawaii;
Puerto Rico; Canada.

Outside the toll-free area: 503.885.5700.

E-mail: [e-mail]

Europe

Australia

Select Contact Us at www.utcfssecurityproducts.eu

[e-mail]

Note: Be ready at the equipment before calling.

Online

Another great resource for assistance with your Interlogix product is our online publication library. To access
the library, go to our website at the following location:

http://www.interlogix.com/transmission

1

1. Many Interlogix documents are provided as PDFs (portable document format). To read these documents, you will

need Adobe Reader, which can be downloaded free from Adobe’s website at www.adobe.com.

Product Disassembly Instructions for WEEE

Per European Directive 2002/95/EC Waste Electrical and

Electronic Equipment

Required Tools:

One number 2 Phillips (crosstip) screwdriver.
One number 2 flat screwdriver.

For the enclosed box version:

1. Locate and remove box cover securement screws. Usually, but not limited to, at least
4 screws.

2. Lift off box top cover.

3. Locate and remove securement screws for printed circuit board.

4. If there are multiple boards to the assembly, continue removing securement screws
until none are left.

5. Lift off printed circuit board.

6. Disassembly of box version of product is complete.

For rack version:

1. Locate and remove securement screws for printed circuit board. Usually, but not
limited to, at least 4 screws.

2. If there are multiple boards to the assembly, continue removing securement screws
until none are left.

3. Lift off printed circuit board(s).

4. Disassembly of rack card version of product is complete.

Copyright © 2011 UTC Fire & Security. All rights reserved.

r

Trademarks and

patents

Manufacture

Certification

ACMA compliance Notice! Thi

Canada This Class A digital apparatus complies with Canadian ICES-003.

European Union

directives

Interlogix and IFS names and logos are trademarks of

UTC Fire & Security.
Other trade names used in this document may be trademarks or

registered trademarks of the manufacturers or vendors of the
respective products.

UTC Fire & Security Americas Corporation, Inc.

2955 Red Hill Avenue, Costa Mesa, CA 92626-5923, USA
Authorized EU manufacturing representative:

UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands

N4131

product may cause radio interference in which case the user may be
required to take adequate measures.

Cet appareil numérique de la classe A est conforme à la norme
NMB-0

2004/108/EC (EMC directive): Hereby, UTC Fire & Security

decl
requirements and other relevant provisions of Directive
2004/108/EC.

03 du Canada.

ares that this device is in compliance with the essential

s is a Class A product. In a domestic environment this

2002/96/EC (WEEE directive): Products marked with this symbol

cannot be disposed of as unsorted municipal waste in the European
Union. For proper recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see:
www.recyclethis.info.

Contact information For contact information, see www.interlogix.com.