Interlogix D1210-R3, D1210 Specsheet
GE
D1200 Series
Security
Overview
The IFS D1200 series data transceivers provide point-topoint transmission of simplex or duplex T1, E1 (CCITT) data
signals over two optical fibers. Models within this series
are available for use with multimode or singlemode optical
fiber. Plug-and-play design ensures ease of installation
requiring no electrical or optical adjustments. Each
transceiver incorporates power, carrier detect and
transmit/receive data status indicating LED’s for monitoring
proper system operation. The modules are available in
either stand-alone or rack mount versions.
Application Examples
• E1/T1 Multiplexed Telephony Systems
• Emergency Phone Stations
• Computer/Data Equipment
• ITS Traffic Signalization Networks
IFS T1, E1 (CCITT) Transceiver
Standard Features
• Supports T1, E1 (CCITT) Data
• Transparent to AMI and Zero Code Suppression
Encoding Schemes
• Data Rates up to 2.048 Mbps
• No In-field Electrical or Optical Adjustments Required
• Power, Carrier Detect, Transmit and Receive Data Status
LED Indicators
• Tested and Certified by an Independent Testing
Laboratory for Full Compliance with the Environmental
Requirements (Ambient Operating Temperature,
Mechanical Shock, Vibration, Humidity with Condensation,
High-Line/Low-Line Voltage Conditions and Transient
Voltage Protection) of NEMA TS-1/TS-2 and the Caltrans
Specification for Traffic Signal Control Equipment.
• Point-to-Point Network Architecture
• Automatic Resettable Solid-State Current Limiters
T1, E1 (CCITT)
Transceiver
Provides point-to-point transmission
of simplex or duplex T1, E1 (CCITT)
data signals over two optical fibers.
• Hot-Swappable Rack Modules
• Distances up to 43 Miles (69 km)
• Comprehensive Lifetime Warranty
D1210
T1 Multiplexer T1 Multiplexer
D1210
2 Fibers
62.5/125 m MM
Voice, RS-232 or RS-422
1 2 24
1 2 24
{
Voice, RS-232 or RS-422
{
up to 1.2 miles
(2 km)
ifs
International
Fiber
Systems
Incorporated
203.426.1180
ifs
International
Fiber
Systems
Incorporated
203.426.1180
GE
Security
North America
T 888-GE-SECURITY
888-437-3287
F 503-691-7566
E sales@ifs.com
Asia
T 852-2907-8108
F 852-2142-5063
Australia and New Zealand
T 613-9239-1200
F 613-9239-1299
Europe
T 44-113-238-1668
F 44-113-253-8121
Latin America
T 305-593-4301
F 305-593-4300
gesecurity.com/ifs
Specifications subject to
change without notice
© 2008 General Electric Company
All Rights Reserved
Specifications
Data
Data Interface: T1, E1 (CCITT)
Data Rate: DC to 2.048 Mbps, Transparent to zero suppression code
Impedance (T1): 100 ohms (twisted pair)
Impedance (E1): 120 ohms (twisted pair)
Wavelength D1210: 850 nm, MM D1220: 1310 nm, MM D1225, D1230: 1310 nm, SM
Number Of Fibers 2
Connectors
Optical: ST
Data and Power: Terminal Block with Screw Clamps
Electrical & Mechanical
Power:
Surface Mount: 24 VAC CT @ 250 mA
Rack: From Rack
Number of Rack Slots: 1
Current Protection: Automatic Resettable Solid-State Current Limiters
Circuit Board: Meets IPC Standard
Size (in./cm.) (LxWxH)
Surface Mount: 7.0 x 4.8 x 1.0 in., 17.8 x 12.2 x 2.5 cm
Rack Mount: 7.0 x 4.9 x 2.0 in., 17.8 x 12.5 x 5.0 cm
Shipping Weight: < 2 lbs./0.9 kg
Environmental
MTBF: > 100,000 hours
Operating Temp: -40° C to +74° C
Storage Temp: -40° C to +85° C
Relative Humidity: 0% to 95% (non-condensing)†
†May be extended to condensation conditions by adding suffix ‘–C’ to model number for conformal coating.
Agency compliance
Made in the USA
Complies with FDA Performance
Standard for Laser Products, Title 21,
Code of Federal Regulations, Subchapter J
System Design
Ordering Information
Part Number Opt. Pwr. Budget Max. Distance*
Multimode
62.5/125µm**
Single Mode
9/125µm
Accessories♦
Options
*Optical transmission distance is limited to optical loss of the fiber and any additional loss introduced by connectors, splices and patch panels.
Distance can also be limited by fiber bandwidth. **For 50/125 Fiber, subtract 4 dB from Optical Power Budget. ♦All accessories are third party manufactured. v WDMA must mate with a WDMB
D1210
D1220
D1225
D1230
PS-24ACCT 24 VAC C.T. Transformer Included
Add ‘-24’ for 24 VDC Power (Extra charge, consult factory)
Add ‘-R3’ to Model Number for R3 Rack Mount - No Charge (Requires R3 Rack purchased separately)
Add ‘-C’ for Conformally Coated Printed Circuit Boards (Extra charge, consult factory)
Description
T1/E1 Compatible Data Link, LED (850 nm)
T1/E1 Compatible Data Link, LED (1310 nm)
T1/E1 Compatible Data Link, LED (1310 nm)
T1/E1 Compatible Data Link, Laser (1310 nm)
Fibers Required
2
2
13 dB
14 dB
23 dB
1.2 miles (2 km)
8 miles (13 km)
25 miles (40 km)
43 miles (69 km)
Loading...