Interlink electronics VP4150, VP4160 User Manual

FCC Certication

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a CLASS B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a residential
installation. This equipment generates, uses, can radiate radio frequency energy and if not
installed and used in accordance with the instruction guide, may cause harmful interference to
radio communications. However, there is no guarantee that this radio interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment on and off, the user is encouraged
to try to correct the interference by one or more of the following measures:
Re-orient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Consult the dealer or an experienced Radio-TV technician for help.

Notice: Any changes or modications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment. Extension cables are not
recommended, if used, they must be shielded in order to comply with the emission limits.

IC Certication

The term “IC” before the certication/registration number only signies that the Industry Canada
technical specications were met.

Declaration of conformity

Manufacturer: SMK-Link Electronics Corporation
3601-B Calle Tecate
Camarillo, CA 93012
Hereby, SMK-Link. declares that the VP4150 is in compliance with the essential requirements

and other relevant provisions of Directive 1999/5/EC.
EMC/EMI/Safety Standards:

EN 300 440-2 V1.1.1 (2001-09)
EN 301 489-1 V1.4.1 (2002-08)
EN 301 489-3 V1.4.1 (2002-08)
EN 60825-1 (1994, A11:1996, A2:2001)

CLASSII LASERPRODUCT

LASER RADIATION–DO NOT

STARE INTOBEAM

WAVELENGTH:635nm

MAXOUTPUT: <1mW

Users Manual

VP4150/VP4160

Thank you for purchasing a VP4150 RemotePoint Navigator.
We know you had other choices and we appreciate that you
chose Interlink Electronics by SMK-Link for your wireless
needs. So that we may better serve you in the future, please
register online at
www.smklink.com/register.

Thank You

WarranTY

Two Year, Limited Warranty

SupporT

SMK-Link Electronics Corporation
3601-B Calle Tecate
Camarillo, CA 93012

TEL: [phone]
FAX: [phone]

FirST uSe

1. Install batteries in the battery compartment.

2. With the computer turned on, plug the receiver into a free USB
port. (If the computer displays a “Found New Hardware” dialog
box, click Next until the driver is installed.)

3. Initialize the RemotePoint Navigator by pressing the Blank
button within 10 minutes of connecting the receiver.

Changing The Blank keY Code

In certain languages a dierent key code may be needed to blank the screen during a
presentation. Three key codes are provided for the various presentation programs.
To change between the codes:

Insert the receiver into a USB port.
Use a paper clip to press and release the recessed button on the reciever.
The LED on the receiver will turn orange.
Start a slide show and test the Blank screen feature.

•

•

•

•

SeTTing up The remoTepoinT navigaTor

Your presentation remote comes set up from the factory. In most situations no adjust­ments are needed; however, if you have many remotes or another device which is
causing interference, complete these steps to avoid interference.

1. To train the receiver to accept the digital code from the remote, remove the USB
receiver from the USB port and reconnect it after a few seconds.

2. Press and hold the Next button (the right arrow) for 10 seconds until the red light
on the remote turns back on. The LED on the receiver should turn from ashing
green to solid green then back to ashing green.

1. Remove the battery from the remote.

2. Replace the battery and hold down the Previous button (the left arrow) for 10
seconds.

3. The LED on the remote will blink the number of the current channel. Each time you
press the Previous button it increases the channel by one.

4. Once you are on channel 4, inceasing the channel will move it back to channel 1.

5. The LED will blink rapidly the number of the current channel.

6. Press the Next button (the right arrow) to conrm the channel.

7. Train the receiver again using the steps listed in “Training the Receiver.”

Training The reCeiver

Changing ChannelS

remoTepoinT navigaTor ConTrolS

Next Slide

Blank Presentation

Activate Laser

Previous Slide