T 7
™
D I V I N G S Y S T E M
Assembly & Installation Instructions
ON
ATTENTI
INSTALLERS:
Please del
review t
HOMEOW
s manual
hi
ver
i
and
NER
wi
.
th
Visit inter-fab.com to view our installation help video.
(Video does NOT replace installation instructions.)
3 0 5 0 S . A L V E R N O N W A Y • T U C S O N , A Z 8 5 7 1 3
5 2 0 . 7 9 0 . 7 0 4 0 • 8 0 0 . 7 3 7 . 5 3 8 6 • F A X 5 2 0 . 7 9 0 . 7 1 2 7
i n t e r - f a b . c o m
T7-IM Rev. 10/17 (BBK-T7 INSTAL)
WARNING
WARNING: IMPORTANT INSTALLATION INFORMATION
The installation of this product should be done only by a licensed
and professional installer. Installation should be done strictly
in conformance with all local building codes, electrical codes
and other building and safety laws and regulations. Among other
things, that your installer should carefully analyze the need to
bond the product to prevent an electrical hazard. Failure to
properly install this product could result in a dangerous condition,
including but not limited to electrical and or structural hazards.
Inter-fab, Inc. disclaims all liability arising from the installation
and the user assumes all risk associated with the installation.
For Technical Support or Assistance,
Contact Customer Service at:
INTER-FAB, INC.
3050 S. ALVERNON WAY
TUCSON, AZ 85713
(800) 737-5386
or visit: www.inter-fab.com
To obtain complete copies of the ANSI/APSP/ICC-5 2011
Standard for Residential Inground Pools or to obtain copies of
the “Plan Your Dive, Steer Up” or “The Sensible Way to Enjoy
Your Inground Swimming Pool” contact:
The Association of Pool & Spa Professionals (APSP)
2111 Eisenhower Ave.
Alexandria, VA 22314
(703) 838-0083
or visit: www.theapsp.org
I N S T A L L A T I O N M A N U A L T 7 ™ D I V I N G S Y S T E M
TABLE OF CONTENTS:
Safety First ............................................................................2
Intended Use Instructions ........................................................3
Important Notices to the Installer..............................................4
Minimum Diving Water Envelope Information...............................5
T7 Placement ........................................................................6
T7 Jig Info & Placement Tips ...................................................7
Step 1: Install Water Feature (optional equipment) ......................8
Step 2: T7 Assembly ..........................................................9-10
T7 Exploded View & Parts List................................................11
T7 Care & Maintenance ........................................................12
Article 5 Extracted from ANSI/APSP/ICC-5 2011 ...............13-16
Pages for Notes ...................................................................17
Inter-Fab Limited Warranty.....................................................18
T7-IM Rev. 10/17 (BBK-T7 INSTAL)
1
I N S T A L L A T I O N M A N U A L T 7 ™ D I V I N G S Y S T E M
WARNING
This Inter-Fab diving board and stand shall be installed only by a professional swimming pool contractor
or with the direct supervision of a licensed professional, engineer or architect. Diving boards may
be installed only on residential inground swimming pools properly designed for their use.
Diving boards that are improperly installed can be very dangerous to the user resulting in possible
serious head and/or spinal column injury, including the paralysis or death of the user.
It is very important that this diving board and stand be installed only on Type 1 or greater pools
build in strict accordance with the American National Standard for Residential Inground Swimming
Pools (ANSI/APSP/ICC-5 2011) and in accordance with the included INTER-FAB RESIDENTIAL
POOL SPECIFICATIONS TABLE 2.
In addition to the above standard and referenced table, these installation instructions provided by
Inter-Fab, Inc. must be diligently followed.
It is also important that any and all warnings provided with the diving board be strictly adhered to
and posted in a conspicuous location. If not provided or they are misplaced, please purchase
warning signs from your pool contractor or professional pool supply store and post them in a location
that the users of the diving board can clearly see.
SAFETY FIRST!
FOR RESIDENTIAL INGROUND SWIMMING POOL USE ONLY
NO COMMERCIAL, PUBLIC OR SEMI-PUBLIC USE IS ALLOWED
ONLY ONE PERSON ON THE DIVING BOARD AT ONE TIME
MAXIMUM WEIGHT = 300 LBS
Plan Your Dive
Back Arched
Arms Extended
PLAN YOUR DIVE, STEER UP
Head and Hands Up
Hold Diving Form
Steer up for a safe dive.
DIVING TIPS: Even the safest equipment must be used properly. Inter-Fab promotes safe diving by
offering these tips on the proper use of your diving board: always dive into water that meets depth
requirements, with arms extended; be aware of the bottom and the walls of the pool; avoid collisions
with pool toys and floats; and instruct your pool users to always “steer up”. When you begin your
dive you must get ready to steer up. As you enter the water, your arms must be extended over
your head, hands flat aiming up. Hold your head and arch your back.
T7-IM Rev. 10/17 (BBK-T7 INSTAL)
2
I N S T A L L A T I O N M A N U A L T 7 ™ D I V I N G S Y S T E M
INTENDED USE
WARNING
INSTRUCTIONS
“A pool is the safest place to swim and a diving board installed in compliance with manufacturers
instructions and the ANSI/APSP/ICC-5 2011 Standard for In-ground Residential Pools is the
safest place to dive from. To ensure that you and your family and guests are able to safely enjoy
your diving board for many years, it is critical that you follow the following instructions.”
DO
1. Know the shape and depth of the pool before
you dive.
2. Make sure that all family members and guests
are familiar with these instructions before they
use your pool and diving board.
3. Make sure that the diving board has been
installed in compliance with the Assembly
and Installation Instructions and with the
ANSI/APSP/ICC-5 2011 Standard for In-ground
Residential Pools. This includes the shape and
depth of the pool as well as the height of the
diving board.
4. Enter feet first the first time.
5. Plan your path to be sure you avoid any other
swimmers, or objects in or under the water,
such as floats, tires, toys etc.
6. Keep your head up, arms up and fully extended
and steer up with your hands.
7. Practice carefully before you dive headfirst.
8. Become familiar with the diving board and its
spring before diving headfirst
9. Dive straight ahead, not to the side of the
board or pool.
10. Dive from the diving board only.
11. Make sure that children and non-swimmers
are supervised at all times.
12. Always remember that when you dive you must
steer up.
13. Inspect your diving board, base and stand on
a regular basis (at least twice a year) and keep
them in proper repair.
14. Contact your dealer, installer or Inter Fab
(800-737-5386) with any questions or concerns
about the safe use of your diving board.
DON’T
1. Don’t drink and dive.
2. Don’t install this or any diving board on an
above ground pool or dive into an above
ground pool from any surface.
3. Don’t dive into a pool from anyplace not specifically designated for diving. Never dive into the
shallow portion of any pool.
4. Don’t dive across the width of the pool or to
the sides of the pool.
5. Don’t Run and dive.
6. Don’t engage in horseplay in or around the diving
board or pool.
7. Don’t use your diving board as a trampoline.
8. Don’t do a back dive. Backyard pools are not
built for that type of activity.
9. Don’t try fancy dives. Keep the dives simple.
10. Don’t dive into or through objects or toys such
as inner tubes.
11. Don’t swim or dive alone.
12. Don’t use a diving board or stand or base that
is rusted or worn out or in poor repair.
THE T7 DIVING SYSTEM IS A JUMP BOARD
T7-IM Rev. 10/17 (BBK-T7 INSTAL)
3
I N S T A L L A T I O N M A N U A L T 7 ™ D I V I N G S Y S T E M
IMPORTANT NOTICES
TO THE INSTALLER
The specifications found on page 5 of this manual represent the minimum water envelope
required by Inter-Fab and by the ANSI/APSP/ICC-5 2011 Standard for Residential Inground
Swimming Pools. Each of these dimensions must be met or exceeded. Installation of a diving
board of any type on a pool that does not meet or exceed each of the minimum specifications as
provided on page 5, including but not limited to the slope requirement, is in direct violation of this
manufacturer’s instructions and the 2011 Standard, and can result in serious injury or death.
The installation of the T7 diving system is not complete until you, the installer have measured the
pool to ensure it meets the Inter-fab residential inground minimum pool specifications and the
ANSI/APSP/ICC-5 2011 Standard for Residential Inground Swimming Pools
The installation of the T7 diving system is not complete until you the installer has delivered to your
customer and reviewed with your customer the “Owners Manual” as well as the “Plan Your Dive
Steer-Up” brochure.
The T7 diving system (diving board, springs, and base) is a complete system and must be installed
as a complete system. It is strictly prohibited to install any T7 component on any other stand,
spring, or base.
Inter-fab highly recommends that you, the installer, obtain and consult the ANSI/APSP/ICC-5 2011
Standard for Residential Inground Swimming Pools before proceeding with the installation.
CHECK YOUR LOCAL ELECTRICAL CODE FOR BONDING REQUIREMENTS. USE ANTI-SEIZE
ON ALL HARDWARE.
THE T7 DIVING SYSTEM IS A JUMP BOARD.
ONLY ONE PERSON AT A TIME ON THE DIVING BOARD,
WITH A MAXIMUM WEIGHT LIMIT OF 300 LBS.
T7-IM Rev. 10/17 (BBK-T7 INSTAL)
4
I N S T A L L A T I O N M A N U A L T 7 ™ D I V I N G S Y S T E M
MINIMUM DIVING WATER ENVELOPE:
NOTE: DRAWINGS ARE NOT TO SCALE.
F
G
IVING EQUIPMENT
D
TIP OF BOARD
ABOVE POINT A
DIVING EQUIPMENT
H
N
M
L
J
K
TABLE 1 - MINIMUM WATER ENVELOPE (ANSI/APSP/ICC-5 2011)
MINIMUM DEPTHS
POOL
TYPE
A B C D A B C D WA AB BC CD* DE WE
0
I 6’-0” 7’-6” 5’-0” 2’-9” 10’-0” 12’-0” 10’-0” 8’-0” 1’-6” 7’-0” 7’-6” VARIES 6’-0” 28’-9”
II 6’-0” 7’-6” 5’-0” 2’-9” 12’-0” 15’-0” 12’-0” 8’-0” 1’-6” 7’-0” 7’-6” VARIES 6’-0” 28’-9”
III 6’-10” 8’-0” 5’-0” 2’-9” 12’-0” 15’-0” 12’-0” 8’-0” 2’-0” 7’-6” 9’-0” VARIES 6’-0” 31’-3”
IV 7’-8” 8’-6” 5’-0” 2’-9” 15’-0” 18’-0” 15’-0” 9’-0” 2’-6” 8’-0” 10’-6” VARIES 6’-0” 33’-9”
V 8’-6” 9’-0” 5’-0” 2’-9” 15’-0” 18’-0” 15’-0” 9’-0” 3’-0” 9’-0” 12’-0” VARIES 6’-0” 36’-9”
AT POINT
D I V I N G E Q U I P M E N T P R O H I B I T E D
MINIMUM WIDTHS
AT POINT
MINIMUM LENGTHS
BETWEEN POINTS
TABLE 2 - INTER-FAB RESIDENTIAL POOL MINIMUM SPECIFICATIONS
MAX. DIVING
BOARD LENGTH
POOL
TYPE
DBL** HOW** F G H J K L M N
0
I 6’ DB/6’ JB/7’ T7 20” 2’-9” 5’-0” 4’-0” 7’-2.5” 7’-6” 6’-0” 3’-9” 2’-1.5” 12’
II 8’ DB/6’ JB/7’ T7 20” 2’-9” 3’-10” 4’-2” 7’-2.5” 7’-6” 6’-8” 3’-9” 2’-1.5” 12’
III 10’ DB/8’ JB/7’ T7 26” 2’-9” 4’-4.75” 4’-4.5” 7’-5.5” 8’-0” 6’-7” 3’-11.5” 1’-7.5” 13’
IV 10’ DB/8’ JB/7’ T7 30” 2’-9” 5’-10.5” 3’-10” 7’-8” 8’-6” 8’-3” 5’-7” 2’-7” 13’
V 12’ DB/8’ JB/7’ T7 40” 2’-9” 6’-2” 3’-11.5” 7’-9.5” 9’-0” 8’-2.5” 5’-9” 2’-7” 14’
MAX. HEIGHT
OVER WATER
AT POINT A
D I V I N G E Q U I P M E N T P R O H I B I T E D
CROSS SECTIONAL
DIMENSIONS AT
POINT A
CROSS SECTIONAL DIMENSIONS AT POINT B
MIN. HEAD
ROOM
ABOVE
DIVING
SURFACES
NOTES:
*Min. length between points CD may vary based upon water depth at point D and the slope between points C & D
ABBREVIATIONS: **DBL=Diving Board Length; DB=Diving Board; JB=Jump Board; **HOW=Height Over Water
T7-IM Rev. 10/17 (BBK-T7 INSTAL)
5
I N S T A L L A T I O N M A N U A L T 7 ™ D I V I N G S Y S T E M
NOTE: READ THESE INSTRUCTIONS IN THEIR ENTIRETY BEFORE ATTEMPTING T7
INSTALLATION.
FIG. A – T7 PLACEMENT SPECIFICATIONS:
*
*optional water stub
up for Board Fall
Concrete Minimums:
8’ Long
4’ Wide
6” Deep
installation
INTER-FAB CANNOT GUARANTEE CUSTOMER’S CONCRETE OR THICKNESS
TABLE 3 – PLACEMENT CHART
IMPORTANT:
TYPICALLY GUNITE CONSTRUCTION
DUE TO THE VARYING SIZES OF OTHER POOLS, TYPICALLY VINYL LINER CONSTRUCTION,
PLEASE CONTACT CUSTOMER SERVICE FOR PROPER JIG PLACEMENT.
THESE DIMENSIONS ARE ACCURATE ONLY FOR VERTICAL POOL WALLS,
, WITH LESS THAN A 3’ RADIUS TO THE POOL FLOOR.
1.800.737.5386
REFER TO: ANSI/APSP/ICC-5 2011 American National Standard for Residential Inground Swimming Pools
(pages 13 through 16) and to page 5 for Inter-Fab Residential Inground Pool Minimum Specifications.
T7 DIVE
STAND
7’ T7 ONLY I 31” 50” 18” 20”
ONLY T7
DIVING
7’ T7 ONLY II 31” 50” 18” 20’
BOARD CAN
7’ T7 ONLY III 25” 50” 24” 26”
BE UTILIZED
7’ T7 ONLY IV 19” 50” 30” 30”
ON T7 DIVE
STAND
7’ T7 ONLY V 13” 50” 36” 40”
NOMINAL
BOARD
LENGTH
ANSI/
NSPI-5
POOL
TYPE
MUST BE INSTALLED ON TYPE I POOL OR GREATER
DISTANCE FROM
WATER’S EDGE TO
FORWARD JIG BOLT
(S) *
DISTANCE FROM
WATER END OF
BOARD TO FORWARD
JIG BOLT
MIN. OVERHANG
POINT A TO
POINT W
MAX HEIGHT OF
BOARD OVER
WATER
(HOW)
T7-IM Rev. 10/17 (BBK-T7 INSTAL)
The top surface of the diving board from the deck end to
the tip end shall be level or have an upward slope of 5/8"
per foot maximum. Elevation difference shall not exceed
4-3/8" from the deck end to the tip of the board. There
shall be no downward slope towards the water. The slope
shall be measured using a level as shown in the graphic
to the left.
6
I N S T A L L A T I O N M A N U A L T 7 ™ D I V I N G S Y S T E M
MOUNTING JIG:
SIDE VIEW TOP VIEW
T7™ JIG INFO:
RED
CAP
YELLOW
CAPS
TOWARD POOL
JIG PLACEMENT TIPS:
• T7 Installation limited to Residential Inground Swimming Pools conforming to a Type I or greater dimension
in accordance with the ANSI/APSP/ICC-5 2011 Standard and Inter-Fab’s Residential Inground Swimming
Pool Minimum Specifications.
• Install jig on the deep end of the pool on centerline.
• Before installing the T7 jig ensure the concrete deck surrounding the jig meets the minimum 8’ long x 4’
wide x 6” deep minimum.
• Comply with all local and national electrical codes when bonding jig.
• Be careful to ensure that the red capped bolt is toward the pool and set back from the water’s edge at the
correct distance based on the table on page 6.
• The 3 jig bolts must extend 2” above the final deck surface.
• Ensure the deck surrounding the jig and base is flat and level so the base makes uniform contact with the deck
surface.
• Leave the protective caps on the bolts until the concrete has cured and base/stand is ready to be installed.
• If installing a Board Fall with the T7 ensure that a 1/2” water stub-up is located per the diagram on page 6
and as shown in the above illustration. Provide a minimum of 10 gallons per minute to the end of the T7
diving board.
T7-IM Rev. 10/17 (BBK-T7 INSTAL)
7
I N S T A L L A T I O N M A N U A L T 7 ™ D I V I N G S Y S T E M
T7 Diving System
INSTALLATION INSTRUCTIONS
IMPORTANT: The gel coat surface of the T7 Diving System is similar to a high quality marine finish; it is
long lasting, strong and beautiful but will scratch if mishandled.
Do not place unprotected parts on the ground. Do not slide or pull unprotected parts along any surface.
Be careful unpacking parts and with tools during assembly.
BOARD FALL CONFIGURATION: (OPTIONAL EQUIPMENT)
1. BOARD FALL: kit consists of Edgewater, Mounting Hardware (4 screws), 8’ & 4” of 1/2” Flex PVC Pipe,
1-Union
STEP 1: INSTALL WATER FEATURE: (OPTIONAL EQUIPMENT)
If purchased, attach the optional waterfall assembly to the underside of the diving board as follows:
IMPORTANT: To keep the T7 water feature from clogging, ensure water is from a filtered return line
from the pool.
A) The center (central) rib on the underside of the diving board is hollow and is capped at the factory. Remove the
cap from front of the center rib exposing the hollow channel.
B) The Board Fall comes from the factory with an 8' length of 1/2" flex PVC pipe attached. The 8' length
goes thru the board and attaches with PVC glue to one side of the 1/2" union. The 4" length of flex PVC
pipe attaches with PVC glue to the stub-up and then to the other side of the 1/2" union.
C) Once the water tubing is threaded all the way thru the diving board, from the base side, gently pull the end
of the tubing until the waterfall assembly is pulled gently but snugly against the end of the
center rib.
D) Attach the waterfall unit to the Diving Board by inserting the 4 provided screws thru the pre-drilled holes in
the waterfall assembly; hand tighten only (DO NOT USE SCREW GUN), over tightening the screws will
cause them to strip inside the board or break the waterfall housing, and voids the warranty.
ABC
T7-IM Rev. 10/17 (BBK-T7 INSTAL)
8
I N S T A L L A T I O N M A N U A L T 7 ™ D I V I N G S Y S T E M
STEP 2: T7 ASSEMBLY:
TIP: Make sure to use the anti-seizing compound on all the bolts or the nuts will seize.
1. Lay board upside down on packaging being careful not to damage the gel coat surface.
2. Place T7-NSPRING over the 8 bolts on the board as shown in photo below.The single center drill hole in
the spring center faces toward the pool. Use hardware kit T7-102-SS and attach the springs to board
as shown in exploded view in page 11. Hand tighten only at this time.
TIP: The springs are directional. The longer end of the spring goes toward the pool.
3. Board Fall (optional) Board
If installing a Board Fall waterfall, run the hose
through the board as shown in photo. Use the 4
screws provided with the Board Fall unit to
attach to bottom of board.
4. Board Fall (optional) Base
If installing the Board Fall waterfall, remove the
hole black cap on the base by pushing it out
from the underside. Do not try to remove from
the top as damage to the gel coat surface can
occur.
See arrow reference in photo shown.
T7-IM Rev. 10/17 (BBK-T7 INSTAL)
9
I N S T A L L A T I O N M A N U A L T 7 ™ D I V I N G S Y S T E M
STEP 2: T7 ASSEMBLY – CONT.
5. Feed the PVC hose through the base and sit the
ase on the springs as shown in photo.
b
Use hardware kit EDGE-SP and attach the base
to the springs as shown in exploded view on
page 11.
Use a dab of anti-seize provided and tighten
these now to 25-30 ft lbs torque.
6. Tighten the 8 nuts that hold the board to the springs at this time. Torque to 20-25 ft lbs. (Note: all hardware
should be tight at this point of installation)
7. With the assembly upside down and on protective cardboard move as close as possible to mounting jig.
Attach Board Fall waterfall plumbing as described in installation manual “Install Water Feature” on pages
8 and 9.
8. The assembly is now ready to set on the jig bolts. With 2 persons carefully set the assembly upright and
onto the jig. If installing an Board Fall waterfall, tuck the excess hose underneath the base as it is set on
the jig bolts. Using hardware kit T7-NBK attach the base to jig as shown in exploded view on page 11.
Tighten these nuts to 40-50 ft lbs torque.
T7-IM Rev. 10/17 (BBK-T7 INSTAL)
10
I N S T A L L A T I O N M A N U A L T 7 ™ D I V I N G S Y S T E M
T7 DIVING SYSTEM (T7 DB, T7-NBASE, T7-NSPRING):
DRAWING REPRESENTS THE FOLLOWING PART NUMBERS:
T7 DB
T7-NSPRING
T7-NBASE
KITS – QTY. COUNTS
ITEM # COMPONENT DESCRIPTION
1 T7-NBASE-(color code) NO STEP T7 BASE 1
2 T7-DB-(color code) 7’ T7 DIVING BOARD 1
3 T7-NJIG 3 BOLT T7 NO STEP BASE JIG 1
4 T7-NSPRING-(color) T7 NBASE SPRINGS (pair) 1
5 SPRING PAD (factory installed) T7 NSPRING PAD 2
6 BOARD FALL (-L) OPTIONAL WATERFALL FEATURE 1
7 H-1/2 SPA HOSE 1/2” PVC FLEX SPA HOSE GRAY 1
8 H-1/2 NYLON WAS 1/2” FLAT NYLON WASHER 3
9 H-SS 1/2 F WAS 1/2” SS FLAT WASHER 3
10 H-SS 1/2 LOC WA 1/2” SS LOCK WASHER 3
11 H-SS 1/2 H NUT 1/2” SS HEX NUT 3
12 H-1-1/2 WHT CAP .750 X 1-1/2 WHITE UV NUT CAP 3
13 H-SS 3/8 FLT WA 3/8” SS FLAT WASHER 8 12
14 H-SS 3/8 LOC WA 3/8” SS LOCK WASHER 8 6
15 H-SS 3/8 F NUT 3/8” SS FINISH HEX NUT 8
16 H-.562 X .390 CAP .553 X 1/2” GRAY PROTECTIVE CAP 8
17 H-SS 3/8 X 2-1/2 3/8”–16 X 2-1/2” HEX HEAD BOLT SS 6
18 H-SS #8 X 3/4 SS 8 X 3/4” PAN HEAD PHILLIPS SCREW 4
19* H-SS 3/8 NYLON 3/8” NYLON INSERT LOCK NUT 6
20* H-ANTI-SEIZE PACKET OF ANTI SEIZE LUBRICANT (NOT SHOWN) 1 1
* not pictured
T7-NBK
EDGE-SP
T7-102-SS
T7-NBK:
Base to Jig Mounting Hardware
T-7
T7-102-SS:
Board to Springs Mounting
Hardware
EDGE-SP:
Spring to Base Mounting
Hardware
NOTES:
* Part #T7-NBASE comes WITH jig.
The T7 diving board, base, and springs must be used together and cannot be used separately in any other configuration.
T7-IM Rev. 10/17 (BBK-T7 INSTAL)
11
I N S T A L L A T I O N M A N U A L T 7 ™ D I V I N G S Y S T E M
T7™ CARE & MAINTENANCE:
Your T7 diving system requires periodic maintenance to keep it looking like new.*
• Wash Monthly or more frequently, if needed. Be careful to keep cleaning material from
entering the pool.
• Wash with a mild soap such as hand dishwashing soap, avoid using strong cleaners or
abrasives. Avoid strong alkaline (such as tri-sodium phosphate) or highly acidic cleaners.
Avoid bleach and ammonia.
• With the exception of the slip resistant surface on the top of the diving board, wax the
diving system once or twice a year with a good grade paste wax formulated for gel coat
surfaces. CAUTION:
may cause them to become slippery resulting in possible serious injury.
be careful when applying wax. Waxing the slip resistant surfaces
* These suggestions and data based on information believed to be reliable, from our raw materials
manufacturers. They are offered in good faith, but without guarantee, as conditions and methods
of use and procedures are beyond our control.
T7-IM Rev. 10/17 (BBK-T7 INSTAL)
12
I N S T A L L A T I O N M A N U A L T 7 ™ D I V I N G S Y S T E M
SUPPORT INFORMATION: ARTICLE 5 – POOL DIMENSIONS AND TOLERANCES
xtracted from ANSI/APSP/ICC-5 2011, American National Standard for Residential Inground Swimming Pools
E
To obtain complete copies of the
ANSI/APSP/ICC-5 2011
Standard for Residential Inground Pools
contact:
The Association of Pool & Spa
Professionals (APSP)
2111 Eisenhower Ave.
Alexandria, VA 22314
(703) 838-0083
or visit: APSP.org
T7-IM Rev. 10/17 (BBK-T7 INSTAL)
13
I N S T A L L A T I O N M A N U A L T 7 ™ D I V I N G S Y S T E M
SUPPORT INFORMATION: ARTICLE 5 – POOL DIMENSIONS AND TOLERANCES
xtracted from ANSI/APSP/ICC-5 2011, American National Standard for Residential Inground Swimming Pools
E
T7-IM Rev. 10/17 (BBK-T7 INSTAL)
14
I N S T A L L A T I O N M A N U A L T 7 ™ D I V I N G S Y S T E M
SUPPORT INFORMATION: ARTICLE 5 – POOL DIMENSIONS AND TOLERANCES
xtracted from ANSI/APSP/ICC-5 2011, American National Standard for Residential Inground Swimming Pools
E
T7-IM Rev. 10/17 (BBK-T7 INSTAL)
15
I N S T A L L A T I O N M A N U A L T 7 ™ D I V I N G S Y S T E M
SUPPORT INFORMATION: ARTICLE 5 – POOL DIMENSIONS AND TOLERANCES
xtracted from ANSI/APSP/ICC-5 2011, American National Standard for Residential Inground Swimming Pools
E
T7-IM Rev. 10/17 (BBK-T7 INSTAL)
16
I N S T A L L A T I O N M A N U A L T 7 ™ D I V I N G S Y S T E M
NOTES:
T7-IM Rev. 10/17 (BBK-T7 INSTAL)
17
I N S T A L L A T I O N M A N U A L T 7 ™ D I V I N G S Y S T E M
LIMITED WARRANTY
Inter-Fab, Inc. will repair or replace, at its option, any product manufactured by Inter-Fab, Inc. that fails during
he applicable warranty period because of a manufacturing or material defect; provided that the defect is not
t
the result of improper installation, improper use or care, negligence, alterations or modifications to the product,
or natural accidents (acts of God). The applicable warranty period for products manufactured by Inter-Fab,
Inc. is three (3) years from the date of retail purchase, except as specified below:
Pool Games equipment warranty periods are as follows: Volleyball Poles, Basketball Poles, Basketball Rim,
and Basketball Backboard are one (1) year from date of retail purchase. Volleyball, Volleyball Net, Basketball,
Basketball Net, and pumps are warranted for ninety (90) days from date of retail purchase.
The Board Fall water features, used for the T7™ and aquaBoard™ products, have a warranty period of one
(1) year from the date of retail purchase.
Zoomerang™ slide products warranty period is one (1) year from the date of retail purchase.
Build Your Own Slide™* (BYOS™), Build Your Own Slide 2™* (BYOS 2™), Garden Ride Series™*, River Run
Series™*, In-Pool Seating™, Pool/Spa Table™, Pool Seat™ and Sun Shelf Table™ products warranty periods
are one (1) year from the date of retail purchase.
City 2™ Slide and City Base™ products warranty period are one (1) year from the date of retail purchase.
Unless expressly stated otherwise all products manufactured by Inter-Fab are for residential installation (single
family residence) inground pool use only. Inter-Fab, Inc. expressly disclaims any and all warranties and liability
arising from the installation, alteration, or use of its residential products for any non-residential use such as
semi-public, public, or commercial applications. Products expressly manufactured for commercial installation
and use will be subject to this limited warranty.
This limited warranty is in lieu of all other warranties, whether express or implied. Inter-Fab, Inc. disclaims any
warranty of merchantability or fitness for a particular use, and noninfringement in relation to any of its products
and Inter-Fab, Inc. is not liable for consequential, incidental or specific damages. This warranty is limited to
the repair or replacement of the manufacturing or material defect, or refund of the original purchase price,
whichever is less, at the sole option of Inter-Fab, Inc., and expressly does not cover any labor or reinstallation
expenses related to the replacement of any and all Inter-Fab products. This limited warranty shall be the sole
and exclusive remedy of irrespective of whether the claims are made in contract, tort, warranty, law, equity
or by statue.
This warranty is to the original purchaser of the product only. Inter-Fab’s limited warranty is neither transferable
nor portable from consumer to consumer. The effective coverage date begins at the date of retail purchase.
Product owner or representative must notify Inter-Fab, Inc. (or its wholesale agent) in writing, giving a full
description of the nature of the product defect or failure along with proof of purchase, serial number(s) of the
product and photos within thirty (30) days of the expiration of the applicable warranty period. Inter-Fab, Inc.
reserves the right to physically inspect damaged or defective products or components to determine the cause
of the damage or defect, prior to authorizing repair or replacement of its products.
*Please see specific warranty information for the BYOS, BYOS 2, Garden Ride Series and River Run Series slides.
3050 S. ALVERNON WAY • TUCSON, AZ 85713
520.790.7040 • 800.737.5386 • FAX 520.790.7127 • INTER-FAB.COM
T7-IM Rev. 10/17 (BBK-T7 INSTAL)
18
Loading...