USER MANUAL
XVR-1648
Stand Alone Type
DVR
SYSTEM
(Server)
Front Panel
1
POWER : System Power On/Off
1
2
System Control key : Shortcut button for convenience
2
765
3
8
4
12
10
9
11
3
CD/DVD RW : Back up image to CD/DVD RW
HOLD : Hold JOG
4
Return : Cancel Setup or Return Previous Mode
5
Direction Control Button : Control direction
6
7
Enter : Apply Changing Setup.
8
Channel Selection Button : Select Channel or Input Password.
9
: Set up focus / Increase the backward playback speed
: Select reverse playback
10
11
12
: Pause/resume the play ba ck
:Setup Iris / Sele ct the forward playback
: Increase the forward playback speed
Front Panel
System Control Key
1
DISPLAY : Select Screen Division Mode or Rotation Mode.
SEQ : Select sequence screen mode.
2
3
PANIC : Select the panic recording mode.
ZOOM : Zoom image.
4
5
LOCK : Lock button. Password input needed.
When locked, “LOCK” is displayed on screen. Press lock button to unlock.
1
4
7
2
8
3
5
6
9
6
ARCHIVE : Go to archive setup menu. Password input needed.
7
PTZ : Go to Camera PTZ Control.
8
SETUP : Go to System setup.
SEARCH : Go to Search Mode for Searching Recorded Data.
9
FOCUS / IRIS button
NEAR : Set camera focus nearly.
1
FAR : Set camera focus far.
2
CLOSE : Close camera iris.
3
FOCUS
1 2 3
IRIS
4
OPEN : Open camera iris.
4
Rear Panel
1 2
4
Video IN / Loop Out : 16 camera inputs & Loop out
1
Monitor out : Output the video to AV Monitor.
2
5
S-VHS : Output Video by Connected S-VHS.
3
Spot #1 ~ #4 : Output Spot-out Video to AV Monitor.
Audio In : 4 Audio Input Terminal Related with Camera.
4
Audio Out : 1 Output Audio Data.
5
3
76
98 10
11
12
13
Alarm in : 16 alarm inputs
6
Alarm out : 16 alarm outputs
7
USB : USB port for use the USB memory stick and USB HDD Backup. (5 VDC, 500mA)
8
VGA OUT : VGA main monitor connection
9
RS-232C : Connect external RS-232 devices.
10
ARI/Panic/RS-485 : Alarm Reset, Panic alarm and PTZ connection
11
LAN : Connection to a router or internal network
12
POWER : Power Cable connection.
13
• When System Installation, Please Install under System Power Off Status.
Tip
• Please Use Specific Adaptor when Power Supply.
Start Up
Press the power button.
The DVR startup screen detects and checks the HDD and
CD-RW/DVD-RW.
After startup process is complete, it appear the “logon”
display and input the Password.
(Default password is none. So click the “Logon” button.)
The DVR start the normal operation and show default
display of all 16channels.
Three pop-up displays show current system information
and live log and live alarm situation.
Start Up
• Live System Info
1) The percentage of HDD used.
2) User Connection Information
3) Current recording Frame information
4) Backup situation
•Live log
It shows the live log.
: Live log can be removed by pressing this button.
• Live Alarm
Alarm Detection channel show each channel.
When operator drag the mouse at left side of bottom, this
pop-up screen is appeared.
When pressing each button, the operator can
Control (On/Off) above pop-up screen.
System Setup
Configuring the Live Display
• Press the mouse right button from live display.
It shows the menu screen.
• Select the “DISPLAY” icon and press the “DISPLAY” button.
• Display Type
The operator can select 5 different display type.
• Camera Arrangement
The operator can edit the camera location each
display type. After clicking the one of 16 channel
buttons, select below section. Then display channel
will be changed.
Additionally the operator can select next display with
clicking the arrow buttons.
System Setup
PTZ control
• Select the “PTZ” icon and press the “PTZ” button. PTZ controls appear like above.
1) Select the camera.
2) Control the camera direction.
3) Press this button. The operator can control the PTZ detailed configuration with pop-up
screen.
4) Control the Zoom, Focus, Iris.
5) Assign the Preset.
After moving the location, Select the number and press the “save” button.
Camera will move as assigned location when pressing the “Run” button after selecting the number” .
6) Assign the Pa ttern.
After selecting the number, click the “ Run” button.
System Setup
Search
- The operator can search the recorded data as normal, panorama search1,2.
• Normal Search
Select the “SEARCH” icon and press the “SEARCH” button.
(B)
Logon display shows and input the password.
(C)
(D)
(E)
Playback-> Date/time
(F)
(A)
(A) It shows the backup display.
(B) Select the “Playback” or “Log”
(C) Select the “Date and Time” for search
(D) The window for search in detail.
(E) It shows different color each recording configuration at
(F) It shows the recorded data .
(F) It show recorded area .
- Select the date. In case of date that have recorded data, it shows with
color at (F).
- Select the time,
The operator can select the time from timer or by drag the timeline bar
The display cloor about the recorded data at Timeline appear differently each type like above.
form (F).
- Click the button for playback from (D),
- Playback speed is from X1 to X128 forward and backward.
System Setup
Click button for snapshot archiving from (D).
Then it shows below screen. During the playback, the operator can save the image that want to save.
Input the snapshot tag.
Select the channel,
Select the screen.
Input the Memo.
For saving the image, click the “reserve” button.
(The operator can check the saved image from
Archived Date Management of Archive menu).
The operator can send the image with E-mail.
Input the E-mail address and click “send” button.
For burning directly, click the “Start burning”
button. Then it shows “burn” screen.
Input the archiving tag.
Select the device(CD/DVD,USB)
Foreground: During backup, the operator
can not control the other function.
Background: During backup, the operator
can control the other function.
System Setup
Click button for AVI archiving from (D).
Then it shows below screen. During the playback, the operator can save the AVI file about period that want to
save.
Input the archiving tag.
Select the channel,
Select log, text. rec index table
Input the Memo.
Click the “start” button.
Then “AVI archiving” button color is changed as red.
(For using this function, it should work the playback
certainly. If not, it can not save AVI file).
For stopping, click ”AVI archiving” button again.
Then it shows left screen.
For recording continuously, click the “continue” button.
If want to stop, click the “stop” button.
It shows left screen with archiving data information.
How to burning and reserve is same with how to save the
snapshot.
(The operator can check the saved image from
Archived Date Management of Archive menu).
System Setup
Click button for full screen from (D).
Then it shows below screen.
For returning, drag the mouse to the bottom of screen.
Then appear below icon with return icon.
Click the “return” button then return original screen.
The operator can control the playback speed with above icon
from full screen playback mode.
Click button for viewing the log from (D).
Then it shows left screen. Current log is appeared.
For returning, click the same button again.
Click button for changing the playback display from (D).
The operator can select the playback display mode.
System Setup
Playback-> Live View
Select the “live view”.
Then it shows current live display instead of calendar.
The function with below icon work equally.
Log
Click the “log”.
Then it shows left screen.
Select the date that want to see the log from calendar.
Select the event section that want to see.
Click to start the “search”.
Click the button with viewing with timeline.
System Setup
• Panorama Search1
- The operator can search frame by frame.
Select the log.
Then the recorded data about selected log move as center.
( : location)
For playing the recording data with log, click the log double.
Click same button again for returning original screen.
• Select the channel.
• Select the date.
• Select the time.
• The operator can select the time form timer or by
drag the timeline bar.
• How to search is almost same with normal search.
System Setup
• Panorama Search2
- The operator can search with divided screen per 3 hour.
• Select the channel.
• Select the date.
• How to search is almost same with normal search.
The operator can select the playback location by Drag
and drop Timeline bar.
System Setup
Archiving
- New archiving
• Select the “ARCHIVING” icon and press th e “ARCHIVE”
button.
• Logon display shows and input the password.
It shows the archiving display.
• Select the Start time and End time with timer or timeline bar.
• Click the “query” button.
Then it shows data information at archiving info.
Click button for saving the data after inputting the archiving tag.
(The operator can see the saved data from Archived Data Management.
Click button for burning the dat a.
- Archived Data Management
Then it shows “burn” screen.
Select the device(CD/DVD,USB)
Foreground: During backup, the operator can not control the other
function.
Background: During backup, the operator can control the other
function.
• The operator can see the saved snapshot image and AVI
file form New archiving menu and search menu.
: Detailed information
: Delete
: Burning
System Setup
Setup-System
• Select the SETUP” icon and press the “SETUP” button.
Then select the “SYSTEM” icon. Logon display shows and input the password.
It shows the system setup display.
CAMERA
• Camera Title: Input the Title and description by virtual keyboard.
• Camera color setup: Select the Brightness, Contrast, Tint, Color
The operator can control the color with live display when clicking the button.
System Setup
• PTZ setup: Select the address, protocol and Baud rate each camera.
The operator can control PTZ detailed setup when clicking the button.
• Covert/OSD setup: Select the covert and main display, sp ot OSD setup
※ How to use the virtual keyboard
Click Mouse left button double from the location that operator want to input.
Then it shows the virtual keyboard. Select each character from virtual keyboard.
For using the small character. Click the button.
System Setup
ALARM/EVENT
• Sensor Event Setup: Select the Activation, Active State (High/Low-It is related with sensor type) and input
the description.
• Video Loss Event Setup: Select the video loss Activation.
• Motion Detection Event Setup: Select the Motion Detection Activation and Sensitivity(1~10)
and Motion Area.
The operator can select the motion area from above screen after clicking the button.
After selecting the motion area with mouse drag, click the mouse right button, Then it shows pop-up menu
that related with selection.
System Setup
• Storage Event Setup: Select the File system Event, Smart Event.
Disk Full: When disk full, Activation On/Off.
Smart Check Period: Select from 1 hour to 24 hour.
Smart Warning: When HDD has trouble, Activation
• User Defined Event Setup.
On/Off.
The operator can make the User Defined Event with current event’s mixing.
When happen the over two events at the same time, the operator can setup how it work.
(Mixing condition is “AND” not “OR”)
Setup the detail configuration after entering the “EDITER” with clicking the button.
Select the sensor, motion, Videoloss, Storage Event and User defined Event as user want.
After selecting it, action type can setup from Event Action Setup.
System Setup
• Event Action Setup : Setup what kind of action work about all events that included User Defined Event.
- Digital Out
- Select the event that want to assign the action.
- Select the Activation on/off.
- Active state: Select the operation type(High / Low)
- Dwell: Select the Action Time.
Transparent : It work from Event start time to Event end
time.
Latched : It work during selected period.
(1 ~300 second and until pressing any key)
- E-mail notification
- Remote client notification
- Select the event that want to assign the action.
- Select the Activation on/off.
- Active state: Select the operation type(High / Low)
- Dwell: Select the Action Time.
Transparent : It work from Event start time to Event end
time.
Latched : It work during selected period.
(1 ~300 second and until pressing any key)
: ADD button : DELETE button
- When happen the selected event, it notify the event to
Remote client.
- After selecting the user that event will be notified, check
Activation on/off.
- Then select each event(Senser,Video loss, motion,
Storage, User defined Event) on/off.
System Setup
- Video Popup
-Buzzer
- When happen the selected event, screen pop-up at the
selected monitor.
- After selecting the event(Alarm, motion, User Defined
Event) that want to pop-up, select the activation on/off.
- Assign the channel that want to pop-up each Monitor.
- Assign the pop-up dwell time.
: ADD button : DELETE button
- When happen the selected event, select buzzer on/off.
- After selecting the event(Alarm, motion, video loss,User
Defined Event) that want to buzzer, select the activation
on/off.
- Select the buzzer type (Latched, Transparent)
: ADD button : DELETE button
System Setup
DISPLAY
- Setup the display configuration. When operator want to see live display with sequence mode, it is used.
• Screen Template
- Select the screen division.(1,4,8,9,16 division)
ADD button
DELETE button
EDIT button
-When clicking the ADD or EDIT button, it show the
screen.
- Select the channel.
- Select the location that selected channel want to change.
- Then screen template is made or changed.
- The operator can make new screen template or modify
the current screen template.
System Setup
• Main Display Sequence
- When start the sequence, the operator select and make the working sequence type.
- Press the ADD button.
- Select the dwell time.
- Select the new list(It show blue square) and click mouse
right button.
- Then it show screen template list each division.
- Select the screen template that want to do the sequence.
- The operator can add Max.16EA screen template as
same method.
- When pressing the DELETE button after selecting the list,
list is deleted.
* The Max. list Number is 16EA.
• ADV spot#1~4 Sequence
- How to play and stop the sequence
After clicking mouse right button from live
display, select the “SEQUENCE PLAY” or
“SEQUENCE STOP”
Additionally, press the “SEQ” button from DVR.
In case of advance spot, how to setup is almost same with
main display sequence.
The different thing is only one.
The screen template that can select is only two types.
(1,4 division).
- Press the ADD button.
- Select the dwell time.
- Select the new list(It show blue square) and click mouse
right button.
- Then it show screen template list each division.
- Select the screen template that want to do the sequence.
- The operator can add Max.16EA screen template as
same method.
- When pressing the DELETE button after selecting the list,
list is deleted.
* The Max. list Number is 16EA each spot channel.
System Setup
AUDIO
- Setup the audio configuration.
USER
• User Group
- Live Audio
Select the Live audio channel.
-Network Audio
Select the audio transmitter and receiver
Default user group (administrator, manager, user) can not be delete or edit.
After selecting “ADD” button, the operator can make the new user group with new authority.
When selecting “ ADD” button, it show “add group” screen.
It shows the virtual keyboard when click mouse left button double for inputting the text.
: ADD
: DELETE
: EDIT
After selecting the new group, check the authority that want to have. Then click the “apply” button.
How to EDIT is almost same with ADD after selecting the “EDIT” button.
System Setup
•User
The operator can add, delete or edit the new user.
When selecting the “ADD” button, it shows “add user” screen.
: ADD
: DELETE
: EDIT
After inputting the ID,PW and E-mail by virtual keyboard, click the “OK”.
System Setup
NETWORK
- Setup the audio configuration.
• Network Configuration
z NETWORK SERVICE SETUP
DHCP: In case of “Dynamic IP”, select th e “DHCP”
When clicking the “apply” button, DVR get the IP address automatically after selecting the “DHCP”.
In case of using the” Static IP”, input the IP address and other information manually.
DDNS (Dynamic DNS): This is used with a Dynamic IP address, which may be changed by the ISP at any time.
※ With DDNS, there is no need to enter the IP address on every connection, A name server address is used
instead of.
- Setup DHCP to on or manually input the unit IP address.
- Setup DDNS to On, set the DDNS properties (user name, password, and domain name) and reboot the system.
- To access the DVR using the name server address, the format for the address is :
http:// [user name].[domain]
([Example: http:// mydvr.dyndns.org) (user name: mydvr.domain: dyndns.org)
- User will need to input all of the correct DDNS information into the Network setup in order for the DVR to be
able to update its new IP address to the DDNS server whenever a change occurs.
- If user is using a router in your network configuration, it is the router which must be setup for DDNS, not the
DVR.
WEB SERVICE: If do not check this, user can not connect on Internet Explore.
NET CLIENT SERVICE: If do not check this, user can not connect on the Remote software.
z NETWORK CONFIGURATION
IP, GATEWAY, SUBNET MASK and DNS SERVER : Input the each value.
DDNS Server: Input DDNS server domain name.
Net Client Port : Input net client Service Port # (Default:6400).
Web Service Port : Input the Web server port # (Default: 8080).
Max TX Speed : Setup Max Network TX Speed. (56k – 8mbbs).
♣ After making changes to the Network setup, click Apply.
(The system will prompt you to reboot in order to save change.)
System Setup
• E-mail Server
SYSTEM
Input the DVR name.
Input the Password, name and port of e-mail server for
sending the E-mail.
• General Information
- System ID: Input the DVR’s name
- Site name:
- H/W version: DVR’s H/W version
- S/W version: DVR’s S/W version
- Mac address: DVR’s Mac address
System Setup
•Date/Time
• Update
- Date&Time: Current DVR’s Date and Time
The operator can edit manually.
- Timezone: Select the Timezone.
- Network Time server: Input the network time server’s
domain name for getting the time
automatically.
- the operator can update the F/W by USB device and CD.
After inserting the F/W at USB and CD, connect it at the DVR.
Select the F/W upgrade button then it shows the above screen.
After selecting the F/W from list, select the “upgrade” button.
When finishing the upgrade, DVR is re-boot automatically,
System Setup
STORAGE
• Operation
• Utility
- Operation mode
Select the overwrite/write once(no overwrite)
- Internal recording: It sho w s the internal HDD recording
information.
- Internal Archiving: It shows the internal CD-RW/DVD-RW.
- External Storage: It shows the external device.
• Disk View
-Format
When clicking the “START” button, all date is formatted.
- Check Disk
When clicking the “START” button, it check the bad
sector of HDD.
It shows current HDD’s information.
System Setup
Setup-Record
• Select the SETUP” icon and press the “SETUP” button. Then select the “RECORD” icon.
Logon display shows and input the password. It shows the record setup display.
RECORD MODE
- Select the “record mode” and “weekly/daily”.
- Event Link
Select the sensor channel and user defined event each
channel.
System Setup
NORMAL RECORD
• Parameter
- Drag the time that want to setup.
- Select the resolution.
Click the mouse right button and it shows below list.
: D1(704X480)
: 2CIF(704X240)
: 4CIF(352X240)
In case of recording setup, the operator should setup as 4 divided parts.
The operator can setup Max.120FPS each divided part.
- Select the channel.
- Click the mouse right button from “Frame rate” section.
- Then it shows the frame rate list(1,2,4,8,15,30). Select the frame rate.
- Click the mouse right button from “Quality” section.
- Then it shows the Quality list(low,standard,high, highest)
- the operator can setup other divided part as same method.
- If setup all channels as CIF, 8FPS, all channel setup is finished with one divided part only.
Select the Pre,Post event recording time.
Select the event priority. (Alarm, motion, User defined event)
(it can change the priority by clicking the arrow button after selecting the event).
The operator can select the audio recording channel.
In case of weekly, it is almost same with daily setup.
It can setup each date.
System Setup
• Schedule
- the operator can select recording type(Timer,Motion,Alarm,User Defined) each time, channel.
<Camera View> <Trigger View>
Drag the section that want to select and then click the mouse right button.
It shows the “Select or Deselect” icon.
Screen display type can be changed by selecting the icon(Camera View or Trigger View)
System Setup
INTENSIVE RECORD
- In case of this record, record will be centralized at channel that event is happened as event priority
• Parameter
How to setup is almost same with normal record setup.
But it can not setup each channel.
• Schedule
Drag the camera and time that user want.
Click the right mouse button and check the [RECORD ON].
System Setup
PANIC RECORD
- When pressing the panic button or detecting the panic alarm, select the recording type.
How to setup is almost same with normal record setup.
Sequence Play-Stop
• Select the “SEQUENCE PLAY” icon and press the “SEQ” button.
Then it shows installed sequence display. (Sequence Play/Stop)
Digital Zoom
• Select the “DIGITAL ZOOM” icon and press the “ZOOM” button.
Then it shows Zoom control display.
Click button for returning to live display.
Click the mouse right button for changing the channal.
Then it shows the channel list.
Select the channel that want to change.
Loading...