Intellix DIGI-HD-UHR2-WP Installation Manual
8001 Terrace Ave.
Suite #201
Middleton, WI 53562
Phone: 608-831-0880
Toll-Free: 866-4-MATMIX
Fax: 608-831-1833
Maximum Recommended Distances
1080p
1080i
720p
576i/p
480i/p
Cat 6a
(shielded)
150’
300’
300’
300’
300’
Cat 6
110’
220’
220’
220’
220’
Cat 5e
100’
200’
200’
200’
200’
Instructions
1. Turn off power and disconnect the
audio/video equipment by following the
manufacturer’s instructions.
2. Adjust DIP switches for desired mode.
3. Connect all twisted pair cables (ensure T568B
straight-thru wiring).
4. Connect all HDMI cables.
5. Connect power supplies.
6. Power on attached audio/video devices.
Compatible Devices
Compatible Receivers: DIGI-HD-UHR2-R, DIGI-HD-UHR2-WP-R
Compatible Transmitters: DIGI-HD-UHR2-S, DIGI-HD-UHR2WP-S, DIGI-HD-4X2, DIGI-HD-4X4, DIGI-HD-4X8, DIGI-HD-8X8
Important notice:
Do not attempt to disassemble or alter the extender
housing. There are no user-serviceable parts inside the
unit. Doing so will void your warranty.
To minimize the possibility of equipment damage from
electrostatic discharge (ESD), all source and destination
equipment must be powered off during installation.
Do not connect the extender to a telecommunication outlet
wired to unrelated equipment. Doing so may damage the
unit or any connected equipment. Ensure all connected
twisted pair cabling is straight-through (point-to-point).
Allow proper ventilation to reduce the risk of thermal
failure.
DIGI-HD-UHR2-WP Installation
Manual
The Intelix DIGI-HD-UHR2-WP transmits HDMI up to 300’ over
a single twisted pair cable. In environments with high
electromagnetic interference (EMI), shielded twisted pair
cable should be used.
Built-in HDshāk® technology provides dynamic HDMI,
EDID/DDC and HDCP mode selection, guaranteeing
performance and image quality. Plus, onboard HDMI
amplification and buffering allows multiple extenders to be
daisy-chained for greater distances.
The DIGI-HD-UHR2-WP features electrostatic discharge (ESD)
protection circuitry which safegaurds the HDMI circuit against
static electricity and other destructive stray voltage.
The Intelix DIGI-HD-UHR2-WP conforms to HDMI and HDCP
specifications. Intelix does not guarantee operation with devices that
do not conform
to these
specifications.
The Intelix DIGIHD-UHR2-WP
complies with
HDCP
standards.
Distances and
picture quality
may be affected
by cable grade,
cable quality, source and destination equipment, RF and electrical
interference, and cable patches.
8001 Terrace Ave.
Suite #201
Middleton, WI 53562
Phone: 608-831-0880
Toll-Free: 866-4-MATMIX
Fax: 608-831-1833
DIGI-HD-UHR2-WP-S Transmitter Dip Switch Positions
SW 1
SW 2
SW 3
Mode
Off
Off
Off
1080p, Stereo Audio
Off
On
Off
1080p, 5.1 Audio
On
Off
Off
Use Copied EDID (Run Mode)
On
Off
On
EDID copy (Acquire and store)
On
On
On
1080i, Stereo Audio
DIGI-HD-UHR2-WP-R Receiver Dip Switch Positions
SW 1
SW 2
SW 3
Mode
Off
Off
Off
Normal Mode
Off
On
Off
Compatibility Mode
Troubleshooting
Symptom
Possible Solutions
No signal
Status LED is off
Verify that both ends of the twisted pair
cables use 568B crimp pattern.
Verify HDMI cables and source and
destination HDMI ports are operational.
No signal
Verify the power supplies are connected
to both the send and receive baluns.
Verify the power LEDs on both the send
and receive units are brightly
illuminated.
Unusual colors in the video
Power off the destination device and
power it back on to force renegotiation.
Unplug and re-plug the HDMI cable from
receive balun to force renegotiation.
No signal
Screen is completely snowy
Speckling in the video image
Occasional signal dropouts
Use shorter runs of twisted pair cabling.
Drop the HDMI signal to the next lower
resolution; i.e., decrease resolution from
1080p to 1080i, etc.
Replace the twisted pair cable with a
higher grade twisted pair cable; i.e.,
replace Cat 5e with Cat 6.
Speckling in the video image
If the destination device is incapable of
displaying the video signal, alter the
source signal; i.e., decrease resolution
from 1080p to 1080i, etc.
Video without audio
Change source device to output PCM
other than Bitstream audio
Enable PCM down sampling if supported
by your source device
Copying Display EDID
1. Disconnect the transmitter from the source device.
2. Disconnect the receiver from the destination device.
3. Set transmitter DIP switches to EDID Copy mode (On,
Off, On)
4. Connect the transmitter to the destination device via an
HDMI cable.
5. Connect the 5VDC power supply to the transmitter.
6. The Status LED will flash for 2-3 seconds then remain
solid. The EDID signals have been copied and stored.
7. Disconnect the transmitter from the destination.
8. Change DIP switch settings to EDID Run Mode (On, Off,
Off)
9. Reconnect the transmitter and receiver following normal
installation procedures.
DIP Switch Settings
*The DIGI-HD-UHR2 system must be power cycled for the
changes to take effect. Please remove ALL cables from extender,
change DIP switches, and then reconnect.
DIP Switch Settings
1. DIGI-HD-UHR2-WP-S
a. 1080p, Stereo Audio – The transmitter is preset
with EDID for 1080p video and PCM stereo audio.
b. 1080p, 5.1 Audio – The transmitter is preset with
EDID for 1080p video and Dolby Digital 5.1, DTS
5.1, and PCM stereo audio.
c. Use Copied EDID (Run Mode) – The transmitter
uses custom EDID copied into the transmitter
during installation.
d. EDID copy (Acquire and store) – Installation only
setting used during EDID copy process.
e. 1080i, Stereo Audio – The transmitter is preset
2. DIGI-HD-UHR2-WP-R
with EDID for 1080i video and PCM stereo audio.
a. Normal Mode – Factory default works in most
applications.
b. Compatibility Mode – Certain sources may create
an unstable video image. This may include some
cable/satellite receivers. Try using this setting if
you witness an image that flashes on/off
approximately every 2 seconds.
Loading...