Page 1
Network Camera IT50W
Quick Installation Guide
This guide describes the basic functions of
IT50W Network Camera.
All detailed information is described in the
user's manual.
Intellisystem Technologies - http://www.intellisystem.it
Page 2
Warning Before Install
IT50W Quick Start Guide
Power off the Network Camera
as soon as it is found
smoking or smelt unusual.
Contact your distributor when such
cases happen.
Do not place the Network
Camera around the heat
sources, such as television
or oven.
Keep the Network Camera
away from the direct
sunlight.
Keep the Network Camera
away from the water. If the
Network Camera is wet,
power off immediately.
Contact your distributor when such
cases happen.
Refer to your user's manual
for the operating temperature.
Do not place the Network
Camera in high humid
environments.
Intellisystem Technologies - http://www.intellisystem.it
1
Page 3
IT50W Quick Start Guide
Do not place the Network
Camera on unsteady
surfaces.
Do not disassemble the
Network Camera.
Do not insert any object into
the Network Camera, such as
needles.
Do not touch the Network
Camera when it's lightening.
Do not drop the Network
Camera.
Intellisystem Technologies - http://www.intellisystem.it
2
Page 4
Check package contents
1
IT50W Power adapter
IT50W Quick Start Guide
Camera stand
Software CD
Intellisystem Technologies - http://www.intellisystem.it
Antenna
3
Page 5
Physical description
2
Front panel
Rear panel
IT50W Quick Start Guide
Antenna
Microphone
Lens and manual focus ring
Status LEDs
Network Camera
Model IT50W
SN/MAC: 0002D001XXXX
Made in Taiwan
Note the serial number from the label on the unit.
This serial number is the same as the Ethernet
address,
for example: 0002D1XXXXXX=00-02-D1-XX-XX-XX
Reset button
Intellisystem Technologies - http://www.intellisystem.it
4
Page 6
Install your Network Camera in Ethernet network
3
2. Connect power cord to a power outlet.
5V2A
ETHERNET
IT50W Quick Start Guide
1.Use Ethernet cable to make
connection from Ethernet port
to the hub.
Use Category 5 Cross Cable
when the Network Camera is
directly connected to PC.
Intellisystem Technologies - http://www.intellisystem.it
POWER
COLLISION
1
2
5
LINK
RECEIVE
PARTITION
3
4
5
Page 7
Assign IP address
4
1.Run the IP Installer under the Software Utility directory from software
CD.
2.Click on serial number that
matches the one you just note.
3.Assign a free IP address.
4.I f you want to x the IP
address of the unit, check
the option “Use this IP
whenever system boots”.
IT50W Quick Start Guide
The Internet Explorer Connects to the Network Camera
5
At the initial access to the “Connection
Type” page, the web browser will ask for a
new plug-in installation, the plug in being
Network Camera. This plug-in has been
registered for certification and can be used
to change the parameters at the client’s
site. The user may click on to install the
plug-in. If the web browser does not allow
the user to complete the installation, check
the Internet security in order to set on your
web browser to “Ask confirmation for
download ActiveX control without
electronic Signature” and so refresh the
current web page. If the problem persist
please contact your IT or networking
supervisor.
Intellisystem Technologies - http://www.intellisystem.it
6
Page 8
Set up your wireless conguration for the Network Camera
6
1.Check the SSID currently set on your wireless access point (AP).
2.Go to IT50W's Conguration > Network > WLAN Conguration
3.Type in the SSID consistent
with the setting on your AP.
4.Select the Wireless mode as
"Infrastructure".
5. Click Save
IT50W Quick Start Guide
5V2A
ETHERNET
ADSL/Cab le/Hub
AP
POWER
COLLISION
LINK
RECEIVE
1
2
PARTITION
3
4
5
Note:
1.SSID abbreviated from S ervice Set Identier is the name assigned to the wireless
network. The IT50W's factory SSID setting is set to "default".
2.Select "Ad-Hoc" wireless mode if you want the IT50W to communicate without using an
AP or wireless router.
For setup further conguration, please check user's manual
on the software CD.
Intellisystem Technologies - http://www.intellisystem.it
7
Loading...