IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 1 -
Product name: IT350-IT350W PTZ Network Camera
Release Date: 2006/10/27
Manual Revision: 1.00
Intellisystem Technologies ©Copyright 2006. All rights reserved
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 2 -
Before You Use This Product
The use of surveillance devices may be prohibited in your country by law. The
IT350-IT350W Network Camera is not only a high-performance web-ready camera but
also can be part of a flexible surveillance system. It is the user’s responsibility to ensure
that the operation of such devices is legal before installing this unit for its intended use.
It is important to first verify that all contents received are complete according to the list
in the "Package Contents" chapter. Take notice of the warnings in “Quick installation
guide” before the IT350-IT350W Network Camera is installed, then carefully read and
follow the instructions in the “Installation” chapter to avoid damages due to faulty
assembly and installation. This also ensures the product is used properly as intended.
The IT350-IT350W Network Camera is a network device and its use should be
straightforward for those who have basic network knowledge. The “Troubleshooting”
chapter in the Appendix provides remedies to the most common errors in set up and
configuration. You should consult this chapter first if you run into a system error.
The IT350-IT350W Network Camera is designed for various applications including
video sharing, general security/surveillance, etc. The “How to Use” chapter suggests
ways to best utilize the IT350-IT350W Network Camera and ensure proper operations.
For the creative and professional developers, the "URL Commands of the
IT350-IT350W Network Camera" chapter serves to be a helpful reference to customize
existing homepages or integrating with the current web server.
For paragraphs preceded by the reader should use caution to understand
completely the warnings. Ignoring the warnings may result in serious hazards or
injuries.
Package Contents
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 0 -
Wired or wireless PTZ Network Camera
Power adapter
A/V Cable
Antennas (for IT350W wireless model
only)
Remote Controller
Camera stand
Software CD
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 1 -
Table of Contents
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..3
Software Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Initial Access to the Network Camera . . . . . . . . . . . . . . . . . . . . . . . . .. 9
Installing Plug-in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Check Network Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Add Password to Prevent Unauthorized Access . . . . . . . . . . . . . . . . . 10
How to Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Primary User’s Capabilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Administrator’s Capabilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Fine-tuning for Best Performance. . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Opening Accounts for New Users. . . . . . . . . . . . . . . . . . . . . . .. . . . . . . .20
Build a Multimedia Web Attraction Site . . . . . . . . . . . . . . . . . . . . . . . . .21
Build a Security Application . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . ..25
Definitions in Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
System Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
User Group Administration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Network Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Wireless . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
DDNS & UPnP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Mail & FTP . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Video Codec Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Motion Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 2 -
Camera Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Application Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Viewing System Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Viewing System Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Factory Default . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Remote Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Appendix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
A. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
B. Cleaning the Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
C. Pan/Tilt/Zoom Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
D. URL Commands of the Network Camera . . . . . . . . . . . . . . . . . . . . . . . .62
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Style Convention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
General CGI URL Syntax and Parameters . . . .. . . . . . . . . . . . . . . . . . . .63
Get Server Parameter Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Set Server Parameter Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Available Parameters on the Server . . . . . . . . . . . . . . . . . . . . . . . . . .65
Drive the Digital Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
Query Status of the Digital Input . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
Capture Single Snapshot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
Account Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
System Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Configuration File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Upload File (firmware) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Camera Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Recall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
Preset Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
E. Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 3 -
Installation
Hardware Installation
Please verify tha
t your product package
contains all the accessories listed in the
foregoing Package Contents. Depending on
the user’s application, an Ethernet cable may
be needed. The Ethernet cable should meet the
specs of UTP Category 5 and not exceed 100
meters in length.
Connect the power adapter jack to the
Network Camera before plugging in to the
power socket. This will reduce the risk of
accidental electric shock.
Upon powering up, the device runs through a self-test procedure and the front LEDs will
blink between green and red for a few times. If self-test passes, the LEDs will shut off
and the Network Camera will be on stand-by and ready for software installation. If
self-test fails the red LED will blink several times. Refer to Appendix A for
troubleshooting.
The Network Camera will first detect Ethernet. If it does not connect to Ethernet, the
Network Camera will try WLAN. During the searching and connecting process to the
wireless access point or station, the red LED of the Network Camera will flash every
second. Until the Network Camera is connected to the other wireless device, the red
LED will become lighted. Operating in either network mode, the green LED will flash
every second as heartbeat to indicate alive.
To install in Ethernet
Make sure the Ethernet is firmly connected to a switch hub. After attaching the Ethernet
cable plug in the power adapter. If the LED turns out to be steady green after self-test,
go to next paragraph “Software Installation”. If the Ethernet is not available, the
Network Camera will switch to wireless LAN mode.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 4 -
To install in wireless LAN
If the Ethernet is not available while power on, the Network Camera will search for any
access point with the SSID “default”. Once any access point is found, the LED will turn
green to wait for installation. If the network environment cannot meet the default
settings, install Network Camera in Ethernet to proceed with wireless LAN
configuration.
The Network Camera provides a general I/O terminal block with one digital input and
one relay switch for device control. Pin 1 and Pin 2 can be connected to an external
sensor device and the state of voltage can be monitored from the initial state 'LOW'.
The relay switches Pin 3 and Pin 4 can be used to turn on or off an external device.
Consult with the dealer of the peripherals for correct installation.
1 DI+ INPUT (Max. 50mA, 12VDC)
2 DI- INPUT (Initial state of DI is low)
3 SW_COMMON OUTPUT (open from
SW_OPEN at initial state)
(close with SW_OPEN when set DO to ON)
4 SW_NOPEN OUTPUT (Max. 1A, 24VDC or
0.5A, 125VAC)
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 5 -
Software Installation
In this manual, "User" refers to whoever has access to the IT350-IT350W Network
Camera, and "Administrator" refers to the person who can configure the IT350-IT350W
Network Camera and grant user access to the camera.
At the end of the hardware installation, the Administrator must place the product
software CD into the CD-ROM drive of the PC running in MS Windows. An auto-run
program will pop up (If the program is not on auto-run, go to the root directory of the
software CD and click on “autorun.exe”).
Click on “Network Camera Wizard” item, after the window contains changed, click on
“Installation Wizard” to run installation program.
Upon Installation Wizard’s start up, a searching box will pop up. This program searches
for product on the same LAN:
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 6 -
After searching, Video Servers or Network Cameras will be located by the Installation
Wizard. There may be several entries shown in the window. The Administrator may
differentiate the Network Cameras with the serial number.
For the series number in the “Serial Number” field, please check the label on the bottom
of the IT350-IT350W camera.
The IP addresses shown in the "Current IP Address" field reflect those on the local
network. They may be from the DHCP server. If there is no DHCP server, the camera
will try to find a free IP address (this takes from 15 second to 3 minutes, depending on
the LAN status). The method of finding IP address is seeking from 192.168.0.99, to
192.168.0.254. If any of the address inside this range is free, the Network Camera will
be assigned to this IP address, and its subnet mask would be 255.255.255.0. If none of
the addresses is free, the Network Camera will try the range from 192.168.0.2 to
192.168.0.98. After an IP address is assigned to the camera, the “Activity” status LED
blinks.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 7 -
The new UPnP function will always assign an IP address for the Network Camera. The
Administrator can click on button “Link to selected device” to connect the I.E. to the
camera.
If the camera is not on the IP installer list, click on the “Search” button to search for the
camera on the LAN.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 8 -
For more detailed usage of the Installation Wizard, please refer to the user’s manual of
the Installation Wizard.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 9 -
Initial Access to the Network Camera
Installing Plug-in
For the initial access to the Network Camera in Windows, the web browser may prompt
for permission to install a new plug-in for the Network Camera after a period of time of
downloading. Permission request depends on the Internet security settings of the
user’s PC or notebook. If the highest security level is set, the computer may prohibit
any installation and execution attempt. This plug-in has been registered for certificate
and is used to display the video in the browser. Users may click on to proceed.
If the web browser does not allow the user to continue to install, check the Internet
security option and lower the security levels or contact your IT or networking
supervisor for help.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 10 -
Check Network Settings
The Network Camera can be connected either before or immediately after software
installation onto the Local Area Network. The Administrator should complete the
network settings on the configuration page, including the correct subnet mask and IP
address of gateway and DNS. Ask your network administrator or Internet service
provider for the detail information. By default the Network Camera requires the
Administrator to run installation every time it reboots. If the network settings are to
remain unchanged, disable the Install option. Refer to “Network settings” on the
System Configuration page for details. If any setting is entered incorrectly and cannot
proceed to setting up the Network Camera, restore the factory settings following the
steps in the “Troubleshooting” chapter of the Appendix.
Add Password to Prevent Unauthorized Access
The default Administrator’s password is blank and the Network Camera initially will not
ask for any password. The Administrator should immediately implement a new
password as a matter of prudent security practice. Once the Administrator’s password
is saved, the Network Camera will ask for the user’s name and password before each
access. The Administrator can set up a maximum of twenty (20) user accounts. Each
user can access the Network Camera except to perform system configuration. Some
critical functions are exclusive for the Administrator, such as system configuration, user
administration, and software upgrades. The user name for the Administrator is
permanently assigned as “root”. Once the password is changed, the browser will
display an authentication window to ask for the new password.
Once the password is set, there is no provision to recover the Administrator’s password.
The only option is to restore to the original factory default settings.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 11 -
How to Use
Authentication
After opening the web browser and typing in the URL of the Network Camera, a
dialogue window pops up to request a username and password.
The foreground is the login window and the background shows the message if
authentication fails. The user may check the option box to save the password for future
convenience.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 12 -
Primary User’s Capabilities
Main Screen with Camera View
The main page layout has three parts:
Configuration functions: The camera can be configured using these user interfaces.
Camera View: What the camera sees.
Pan/Tilt/Zoom control buttons: These buttons provide a command interface to
control the aim of the camera.
CCD control buttons: These buttons provide a command interface to control the aim
of the camera.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 13 -
The Configuration:
“Digital Output”
Clicking on the “On” or “Off” button turns the digital output to either on or off
status.
“Snapshot”
Clicking on the “Snapshot” can get a JPEG format image of the current camera view
in another window.
“Client Settings”
Clicking on this button links you to the client setting page, please check the
following session for more details.
“Configuration” Only the Administrator can access camera configurations.
The camera view
The information bar down of the IT350-IT350W camera view shows the assigned
caption and the current date/time. The information bar at the bottom of the
IT350-IT350W camera view shows the current streaming mode and audio
transmission mode. You can push/toggle the talk button to talk to the remote
server. The volume of speaker and microphone can also be adjusted.
The camera view provides not only the live video, but also a way to aim the
Network Camera to different target. Using mouse to click on the target inside the
video will command the Network Camera to aim at the target and with the mouse
wheel up or down, the camera view will zoom out or in.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 14 -
The pan/tilt/zoom control buttons:
The direction buttons are for Left, Right, Up, Down, and Home functions. The Home
button centers the camera.
“Go to” Once the Administrator has determined the preset positions; the User can
aim the camera using this control.
“Pan speed”
This selection box sets the moving range of the “Left” and “Right” commands.
“Tilt speed”
This selection box sets the moving range of the “Up” and “Down” commands.
“Zoom speed”
This selection box sets the moving range of the “zoom in” and “zoom out”
commands.
“Focus speed”
This selection box sets the moving speed of the “focus near” and “focus far”
commands. The focus function is obvious when the optical zoom time is larger than
7.
“Auto pan”
This button commands the camera to pan from the current position to the left-most and
then to the right-most position. After panning, the camera returns to the original
position.
“Auto patrol”
This button commands the camera to patrol between the preset positions on the Patrol
List, which can be modified on the “Camera control page”. After one patrol cycle, the
camera returns to the original position.
“Stop” This stops the “Auto Pan” command or “Auto Patrol” command.
The CCD control buttons:
The set of the buttons is for controlling focus, iris and zooming.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 15 -
Client Settings
There are four settings for the client side.
Media Options - For the User to determine whether to receive video, audio or both.
Protocol Options – Which allows choosing on connection protocol between client and
server. There are two protocol choices to optimize your usage – UDP and HTTP.
The UDP protocol allows for more real-time audio and video streams. However, some
packets may be lost due to network burst traffic and images may be obscured.
The HTTP protocol must be selected if the network is protected by a firewall which
allows only HTTP Port (80) to be opened. If there is no restriction, UDP protocol is
recommended. Generally speaking, the client’s choice will be in the order of UDP → HTTP.
After the Network Camera is connected successfully, “Protocol Options” will indicate
the selected protocol. The selected protocol will be recorded in the user's PC and will be
used for the next connection. If the network environment is changed, or the user wants
to let the web browser to detect again, manually select the UDP protocol and save, then
return to HOME to connect to the Network Camera.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 16 -
Streaming Options – For users to select the video streaming types. Select
“Streaming Video” options, the video connection will keep alive to enable you to see
smooth video, while “Single JPEG” options will let you see the video in JPEG format by
client periodic update the JPEG image from server according to the “Frame rate”
settings.
Talk Button Control Style – For the User to determine whether to “click once and
talk” or “push to talk”.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 17 -
Administrator’s Capabilities
Fine-tuning for Best Performance
There are a few choices the Administrator is allowed to maximize the capabilities of the
Network Camera. Best performance generally equates to the fastest image refresh rate
with the best video quality, and at the lowest network bandwidth as possible. The six
factors, “Size”, “Maximum frame rate”, “Video codec type”, “Key frame interval”, “Fix bit
rate”, and “Fix quality” on the Configuration page Video, are correlative to allow for
achieving the best performance possible.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 18 -
For Best Real-time Video Images
To achieve good real-time visual effect, the network bandwidth should be large enough
to allow a transmission rate of greater than 20 image frames per second. If the
broadband network is over 1 Mbps, set the “Fix bit rate” to 1000Kbps or 1200Kbps, or
set “Fix quality” at the highest quality. The maximum frame rate is 25 fps in a 50Hz
system and 30 fps in a 60Hz system. If your network bandwidth is more than 384Kbps,
you can fix the bit rate according to your bandwidth and set the maximum frame rate
to 25 fps or 30 fps. If you are shooting fast-moving images, you may want to slow the
maximum frame rate down to 20 fps in order to lower the rate of data transmission.
This allows for better video quality and the human eyes cannot readily detect the
differences between those of 20, 25, or 30 frames per second. If your network
bandwidth is below 384 Kbps, set the “Fix bit rate” according to your bandwidth and try
to get the best performance by fine-tuning with the “Maximum frame rate”. In a slow
network, greater frame rate results in blur images. Another work-around is to choose
“Half” in the “Size” option for better images, or “Halfx2” for a larger image view. Video
quality performance will vary somewhat due to the number of users viewing on the
network; even when the parameters have initially been finely tuned. Performance will
also suffer due to poor connectivity because of the network’s burst constraint.
In multi-user environment, the user who has poor network performance will receive
only the key frame in MPEG4 format. Try to reduce the key frame interval can improve
the frame rate for poor network performance, but the penalty is the increasing of
network traffic. If the server is running on the Internet, select the “improve efficiency
in the multi-user environment” will improve the efficiency in the multi-user
environment.
Only Quality Images Will Do
To have the best video quality, you should set “Fix quality” at “Detailed” or “Excellent”
and adjust the “Maximum frame rate” to match your network’s bandwidth. If your
network is slow and you receive “broken” pictures, go to the HTTP protocol in
“Connection type” and choose a more appropriate mode of transmission. The images
may suffer a time delay due to a slower connection.
Somewhere Between Real-time and Clear Images
If you have a broadband network, set “Fix quality” at ”Normal” or better, rather than
setting “Fix bit rate”. You can also fix the bandwidth according to your actual network
speed and adjust the frame rate. Start from 30 fps down for best results but not below
15 fps. If the image qualities are not improved, select a lower bandwidth setting.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 19 -
Select for Motion JPEG
The Network Camera with Pan/Tilt/Zoom is a camera with dual video codec, they’re
MPEG4 and MJPEG. If MJPEG is selected, the camera will transmit video data in JPEG
format. Therefore, it requires higher bandwidth to view smooth video. General
speaking, each normal sized JPEG image would be 3k~12k bytes, depending on the
selected video quality and contents. Together with the frame rate selected, the
administrator can control the bandwidth of each connection.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 20 -
Opening Accounts for New Users
Protect Network Camera by Passwords
The IT350-IT350W Network Camera is shipped without any password by default. That
means everyone can access the IT350-IT350W Network Camera including the
configuration as long as the IP address is known. It is necessary to assign a password
if the IT350-IT350W Network Camera is intended to be accessed by others. Type a new
word twice in the first field to enable protection. This password is used to identify the
administrator. Then add an account with user name and password for your friends in
the second field. The IT350-IT350W Network Camera can provide twenty accounts for
your valuable customers or friends. Each account identifies the access right rather than
the real visitor. That allows multiple visitors share the same account of different level.
Each account has four kinds of privileges, which can be set individually. The “I/O
access” privilege permits the user to access DI/DO of the server. The “Camera
Control” privilege allows different control to pan/tilt functions of the IT350-IT350W
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 21 -
Network Camera. The “Talk” privilege permits the user to send speech to the
IT350-IT350W Network Camera. The “Listen” privilege permits the user to listen
sounds from the server. You may edit or delete some users from the third field.
More Flexible Options for Viewers
If you want to have a guest account for viewers only, you just need to add a user
without password and disable all the privileges. Share the account to your friends to
access your camera.
Build a Multimedia Web Attraction Site
Demo on Multiple Sites – Mid-scale Service
The IT350-IT350W Network Camera can allow ten visitors on-line simultaneously. After
Installation, focus the IT350-IT350W Network Camera on any object you wish to share,
and tell the visitors to type in the web browser address. Caution: You may want to
maintain your visitor’s list in the security configuration page to block out unexpected
visitors.
Product Demo for E-business – Large-scale Service
If the number of visitors has exceeded the limit, the IT350-IT350W Network Camera
can allow the "overload" viewers to see the snapshots in JPEG mode, on the homepage.
These are still images and will be refreshed periodically and automatically.
1. Click on “Client Settings” on the homepage,
2. Select “Single JPEG” in “Streaming Options”,
3. Set the snapshot interval to refresh the still image automatically. The longer the
snapshot interval, the better the snapshot mode works for multiple viewers.
If you want to expand to allow in more viewers, the host server should be able to
handle large network traffic, which must handle the picture refreshing from the
IT350-IT350W Network Camera.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 22 -
If the web space has FTP service
Set the Network Camera up as an FTP client to upload the pictures. The access to the
IT350-IT350W Network Camera will be independent of the number of viewers and the
picture quality will remain constant.
1. Click on “Configuration” on the homepage,
2. Click on “Mail & FTP” in the left column,
3. Fill in the FTP related settings including server, server port, user name and password,
as well as the upload path if it is specified by the web space,
4. Click on “Save”,
5. Click on “Application” in the left column,
6. Select the day or days of the week in “Weekly schedule” you want to upload the
pictures,
7. Select “Sequential operation” and set the interval,
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 23 -
8. Unselect “FTP put snapshots with date and time suffix” as the upload method and
click on “Save”,
9. The image file uploaded to the web space is named “video.jpg”. Check if the file is
successfully uploaded to the correct folder,
10. Prepare a homepage with the embedded image reference to the image file
uploaded via FTP in advance.
If the web space has no FTP service
An auto-refresh homepage can be used to periodically poll the newest image from the
IT350-IT350W Network Camera. It is most efficient if using a free web space provider
as the FTP service may be limiting.
1. Prepare an auto-refresh homepage as the following example. The URL of image is
http://<IP address of the Network Camera>/cgi-bin/video.jpg. Modify the IP address
according to your IT350-IT350W Network Camera. Define the refresh interval
according to your network bandwidth for best result. If the refresh rate is too fast and
there is a large number of visitors, this may overload the IT350-IT350W Network
Camera and slows the response.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 24 -
Example of an auto-refresh web page:
<html>
<head>
<title>IT350/IT350W Intellisystem Technologies - Example - auto refresh</title>
</head>
<body>
<p align=left>
<font size="7" face="Comic Sans MS" color="#FF0000">
MiniAVServer Demo
</font>
</p>
<p align=left>
<!-- Begin of scripts to auto refresh the image. Change the IP address in the image
URL and refreshrate if necessary. //-->
<script language=javascript>
var image="http://192.168.0.99/cgi-bin/video.jpg"; //IMAGE URL
var refreshrate=5; //SECONDS BETWEEN REFRESH
var imgwidth=352; //IMAGE WIDTH
var imgheight=240; //IMAGE HEIGHT
function refresh(){
document.images["pic"].src=image+"?"+new Date();
setTimeout('refresh()', refreshrate*1000);}
document.write('<img src="'+image+'" height="'+imgheight+'"
width="'+imgwidth+'" name="pic">');
if(document.images)window.onload=refresh;
</script>
<!-- End of scripts to auto refresh the image. //-->
</p>
</body>
</html>
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 25 -
Build a Security Application
The Administrator can combine options on the application page to perform many useful
security applications. There are two trigger sources coming from attached devices,
such as for motion detection. There are also two kinds of actions responding to such
events, including uploading snapshots over the Internet and driving other attached
devices. To upload the snapshots, the User can choose either email or FTP according to
user’s needs. Both e-mail and FTP use the network settings on the Mail & FTP page.
Refer to the definition section for detail configuration.
1. Click on “Configuration” on the homepage,
2. Click on “Application” in the left column,
3. Check the weekdays as you need and give the period of "Snapshots begin" time and
"Snapshots end" time to monitor the triggering conditions every day,
4. Check the “Event operation”. The triggering condition can be set to detected motion
or status of the attached device,
5. Set the delay before detecting next event to avoid continuous false alarms following
the original event,
Send Snapshots When Motion is Detected
If no external sensor is available, the Administrator can use the built-in motion
detection to monitor any movement and send snapshots via emails for security check.
6. Click on “Motion detection” in the left column,
7. Check “Enable motion detection”,
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 26 -
8. Click on “New” to have a new window to monitor video,
9. Type in a name to identify the new window,
10. Use the mouse to click, hold, and drag the window corner to resize or the title bar
to move,
11. Fine-tune using the “Sensitivity” and “Percentage” fields to best suit the camera’s
environment. Higher ”Sensitivity” detects the slighter motion. Higher “Percentage”
discriminates smaller objects,
12. Clicking on “Save” enables the activity display. Green means the motion in the
window is under the watermark set by the Administrator and red means it is over the
watermark,
13. Click on “Application” in the left column,
14. Check on the window name set in step 9,
15. Check “Upload snapshots while motion detected”, if e-mailing the snapshots is
preferred,
16. Check “Send snapshots by email”,
17. Click on “Save” to validate.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 27 -
Definitions in Configuration
Only the Administrator can access system configuration. Each category in the left
column will be explained in the following pages. The bold texts are the specific phrases
on the Option pages. The Administrator may type the URL below the figure to directly
enter the frame page of configuration. If the Administrator also wants to set certain
options through the URL, read the reference appendix for details.
<url>http://<IT350/IT350WNetworkCamera>/setup/config.html
<IT350/IT350WNetworkCamera>is the domain name or original IP address of the
IT350-IT350W Network Camera.
<url>http://<IT350/IT350WNetworkCamera>/setup/system.vspx
<IT350/IT350WNetworkCamera>is the domain name or original IP address of the
IT350-IT350W Network Camera.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 28 -
System Parameters
"Host name" The text displays the title at the top of the main page.
“Turn off the LED indicator” Check this option to shut off the LED on the rear. It can
prevent the camera’s operation being noticed.
“Automatically restore DO state” The IT350-IT350W Network Camera will set the
DO on when events happened, if the administrator configures it properly in the
Application page. Check this option will restore the DO state to off after specified
seconds.
"Keep current date and time" Click on this to reserve the current date and time of
the IT350-IT350W Network Camera. An internal real-time clock maintains the date and
time even when the power of the system is turned off.
"Sync with computer time" Synchronize the date and time of the IT350-IT350W
Network Camera with the local computer. The read-only date and time of PC is
displayed as updated.
“Manual” Adjust the date and time according to what is entered by the Administrator.
Notice the format in the related fields while doing the entry.
“Automatic” Synchronize with the NTP server over the Internet whenever the
IT350-IT350W Network Camera starts up. It will fail if the assigned time-server cannot
be reached.
“NTP server” Assign the IP address or domain name of the time-server. Leaving the
text box blank connects the IT350-IT350W Network Camera to the default
time-servers.
"Time zone" Adjust the time with that of the time-servers for local settings.
“Update interval” Select hourly, daily, weekly, or monthly update with the time on the
NTP server.
Remember to click on to immediately validate the changes. Otherwise, the
correct time will not be synchronized.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 29 -
User Group Administration
“Root password” Change the Administrator’s password by typing in the new
password identically in both text boxes. The typed entries will be displayed as asterisks
for security purposes. After pressed , the web browser will ask the Administrator
for the new password for access.
“Add user” Type the new user's name and password and press to insert the new
entry. The new user will be displayed in the user name list. There is a maximum of
twenty user accounts. Each user can have four privileges – “I/O access”, “Camera
Control”, “Talk” and “Listen”.
“I/O access” allows user to control the DO and get status of the DI.
“Camera control” allows user to aim the Network Camera to different targets.
“Talk” allows user to talk to the server.
“Listen” allows user to listen from the server.
“Delete user” Pull down the user list to find the user’s name and press to
complete.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 30 -
“Edit user” Pull down the user list to find the user’s name and press to edit the
user’s password and privilege.
<url>http://<IT350/IT350WNetworkCamera>/setup/security.vspx
<IT350/IT350WNetworkCamera>is the domain name or original IP address of the
IT350-IT350W Network Camera.
Edit User
Type the new password, change the privilege and press to modify the account.
<url>http://<IT350/IT350WNetworkCamera>/setup/edituser.vspx
<IT350/IT350WNetworkCamera>is the domain name or original IP address of the
IT350-IT350W Network Camera.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 31 -
Network Settings
Any changes made on this page will need to restart the system in order to validate the
changes. Make sure every field is entered correctly before clicking on .
"Get IP address automatically" & “Use fixed IP address”
The default status is “Get IP address automatically”. This can be tedious having to
perform software installation whenever the IT350-IT350W Network Camera starts.
Therefore, once the network settings, especially the IP address, have been entered
correctly, select “Use fixed IP address” then the IT350-IT350W Network Camera will
skip installation at the next boot. The Network Camera can automatically restart and
operate normally after a power outage. Users can run IP installer to check the IP
address assigned to the IT350-IT350W Network Camera if the IP address is forgotten
or using the UPnP function provided by the Network Camera (MS Windows XP provides
UPnP function at My Network Place). As for how to get IP address automatically,
please refer to the section of Software Installation.
General
“IP address” This is necessary for network identification.
“Subnet mask” It is used to determine if the destination is in the same subnet. The
default value is “255.255.255.0”.
“Default router” This is the gateway used to forward frames to destinations in
different subnet. Invalid router setting will fail the transmission to destinations in
different subnet.
“Primary DNS” The primary domain name server that translates hostnames into IP
addresses.
“Secondary DNS” The secondary domain name server that backups the Primary DNS.
HTTP
“HTTP port” This can be other than the default Port 80. Once the port is changed, the
User must be notified the change for the connection to be successful. For instance,
when the Administrator changes the HTTP port of the Network Camera whose IP
address is 192.168.0.100 from 80 to 8080, the User must type in the web browser
“http://192.168.0.100:8080” instead of “http://192.168.0.100”.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 32 -
Streaming
“UDP Audio channel port” This can be something other than the default port 5002 in
order to work with the port opened by the firewall.
“UDP Video channel port” This can be something other than the default port 5003 in
order to work with the port opened by the firewall.
<url>http://<IT350/IT350WNetworkCamera>/setup/network.vspx
<IT350/IT350WNetworkCamera>is the domain name or original IP address of the
IT350-IT350W Network Camera.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 33 -
Wireless (for IT350W model only)
“SSID” (Service Set Identifier), it is a name that identifies a wireless network. Access
Points and wireless clients attempting to connect to a specific WLAN (Wireless Local
Area Network) must use the same SSID. The default setting is default. Note: The
maximum length of SSID is 32 single-byte characters and SSID can’t be any of “, <, >
and space character.
“Wireless mode” Clicking on the pull-down menu to select from the following
options:
“Infrastructure” Make the IT350W Network Camera connect to the WLAN via an
Access Point. (The default setting)
“Ad-Hoc” Make the IT350W Network Camera connect directly to a host equipped with
a wireless adapter in a peer-to-peer environment.
“Channel” While in infrastructure mode, the channel is selected automatically to
match the channel setting for the selected Access Point. In Ad-Hoc mode, the channel
must be manually set to the same channel for each wireless adapter. The default
channel setting depends on the installed region.
“TX rate” This field is for selecting the maximum transmission rate on the network.
The default setting is “auto”, that is the IT350W Network Camera will try to connect to
the other wireless device with highest transmitting rate.
“Preamble”, either “Long preamble” or “Short preamble” defines the length of the
CRC block (Cyclic Redundancy Check is a common technique for detecting data
transmission errors) for communication between the Access Point and the roaming
wireless device. Long Preamble is the default setting. Note: High network traffic areas
should use the shorter preamble type.
“Data encryption” Checking the box to enable the data encryption. By default it is
disabled.
“Security” Choosing one of the following data encryptions. By default it is disabled.
“None” – disables the data encryption.
“WEP” – uses WEP to encrypt the data.
“WPA-PSK” – uses WPA pre-shared key to encrypt the data.
“Auth. Mode” Choosing one of the following modes, (Auto is the default setting)
“Auto” – Will automatically decide the authentication mode of the wireless client.
“Shared” – allows communication only with other devices with identical WEP settings.
“Open” – communicates the key across the network.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 34 -
“Key length” The administrator can select the key length among 64, 128 or 256 bits.
64bits is the default setting.
“Key format” Hexadecimal or ASCII. “HEX” is the default setting.
“HEX” digits consist of the numbers 0~9 and the letters A-F.
“ASCII” is a code for representing English letters as numbers from 0-127 except “, <,
> and space characters that are reserved.
“Network Key” Entering a key in either hexadecimal or ASCII format. When selecting
different key length, acceptable input length is listed as following:
64 bits key length: 10 Hex digits or 5 characters.
128 bites key length: 26 Hex digits or 13 characters.
Note: When 22(“), 3C(<) or 3E(>) are input in network key, the key format can’t be
changed to ASCII format.
<url>http://<IT350/IT350WNetworkCamera>/setup/wireless.vspx
<IT350/IT350WNetworkCamera> is the domain name or original IP address of the
IT350W Network Camera.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 35 -
DDNS & UPnP
“Enable DDNS” This option turns on the DDNS function.
“Provider” The provider list contains four hosts that provide DDNS services. Please
connect to the service provider’s website to make sure the service charges.
“Host Name” If the User wants to use DDNS service, this field must be filled. Please
input the hostname that is registered in the DDNS server.
“Username/E-mail” The Username or E-mail field is necessary for logging in the
DDNS server or notify the User of the new IP address. Note: when this field is input as
“Username” the following field must be input as “Password”.
“Password/Key” Please input the password or key to get the DDNS service.
“Enable UPnP” This turns on or off the UPnP function. When UPnP is turned off, the
camera cannot be found through network neighbors in MS Windows XP. If the UPnP
network component is installed in Windows XP, the hostname of the IT350-IT350W
Network Camera will be shown with bracketed IP address in the Network neighbors. Ex:
Network Camera with Pan/Tilt (xxx.xxx.xxx.96). That is: The hostname of the Network
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 36 -
Camera is “Network Camera with Pan/Tilt”, and the IP address of the Network Camera
is xxx.xxx.xxx.96, depends on the last value of the IP address assigned to the Network
Camera.
“Save” Click on this button to save current settings for the DDNS service and UPnP
function.
<url>http://<IT350/IT350WNetworkCamera>/setup/ddnsupnp.vspx
<IT350/IT350WNetworkCamera>is the domain name or original IP address of the
IT350-IT350W Network Camera.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 37 -
Mail & FTP
SMTP
“1st SMTP (mail) server” The domain name or IP address of the external email
server.
“1st SMTP account name” Granted account name on the email server.
“1st SMTP password” Granted password on the email server.
“1st recipient email address” The email address of recipients for snapshots or log
file. Multiple recipients must be separated by semicolon, ‘;’.
“2nd SMTP (mail) server” The domain name or IP address of another email server
once the previous server is unreachable.
“2nd SMTP account name” Granted account name on the backup SMTP server.
“2nd SMTP password” Granted password on the backup SMTP server.
“2nd recipient email address” The email address of recipients for the backup server.
“Sender email address” The return email address used in the event the mails fail to
send out.
FTP
“Built-in FTP server port” This can be other than the default Port 21. The User can
change this value from 1 to 65535. After the change, the external FTP client program
must change the server port of connection accordingly.
“1st FTP server” The domain name or IP address of the external FTP server. The
following user settings must be correctly configured for remote access.
“1st FTP server port” The port to access the external FTP server.
“1st FTP user name” Granted user name on the external FTP server.
“1st FTP password” Granted password on the external FTP server.
“1st FTP remote folder” Granted folder on the external FTP server. The string must
conform to that of the external FTP server. Some FTP servers cannot accept preceding
slash symbol before the path without virtual path mapping. Refer to the instructions for
the external FTP server for details. The folder privilege must be open for upload.
“1st FTP passive mode” The IT350-IT350W Network Camera is located inside the
network protected by a firewall, data connection for FTP may be prohibited. By
selecting passive mode, the FTP can bypass the rule and allow snapshot upload to
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 38 -
proceed. If the passive mode is selected, the IT350-IT350W Network Camera can
automatically attempt for active mode, if the external FTP server does not support
passive mode.
“2nd FTP server” The domain name or IP address of the backup FTP server.
“2nd FTP server port” The port to access the backup FTP server.
“2nd FTP user name” Granted user name on the backup FTP server.
“2nd FTP password” Granted password on the backup FTP server.
“2nd FTP remote folder” Granted folder on the backup FTP server.
“2nd FTP passive mode” Passive mode setting for the backup FTP server.
<url>http://<IT350/IT350WNetworkCamera>/setup/mailftp.vspx
<IT350/IT350WNetworkCamera>is the domain name or original IP address of the
IT350-IT350W Network Camera.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 39 -
Video Codec Parameters
“Text on video” The text will be displayed in the black bar above the video window
with a timestamp. The timestamp is captured from date and time of the Network
Camera that is maintained by a built-in real-time clock.
“Color” Select either for color or monochrome video display.
"Size" There are five options for three video sizes. “Half” is the quarter size of
“Normal” and “Normal” is the quarter size of “Double”. “Half x 2” has the same video
size as “Normal” but of a lesser quality, while consuming less network bandwidth.
“Normal x 2” has the same size as “Double” but of a lesser quality.
“Video codec type” It can be either MJPEG or MPEG4. In MJPEG mode, the video
frames are independent. In MPEG4 mode, there are I frames and P frames. To decode
a P frame need the information of previous frame. MPEG4 consumes much less network
bandwidth than MJPEG.
There are five dependent parameters provided for video performance adjustment.
"Maximum frame rate" This limits the maximal refresh frame rate, which can be
combined with the "Video quality control" to optimize the bandwidth utilization and
video quality. If the User wants to fix the bandwidth utilization regardless of the video
quality, choose "Fix bit rate" and select the desired bandwidth. MPEG4 video are
composed by I frames and P frames as the following sequence: IPPPPPIPPPPPIPPPP…
“Key frame interval” determines how many repeated P frames will appear after one
I frame. Large “Key frame interval” can reduce the bit rate, but cause image corrupt
longer if there is packet loss while transmission. “Fix bit rate” option and “Key frame
interval” option are only available in “MPEG4” mode. The video quality may be poor
due to the sending of maximal frame rate within the limited bandwidth when images
are moving rapidly. Consequently, to ensure detailed video quality (quantization rate)
regardless of the network, it will utilize more bandwidth to send the maximal frames
when images change drastically.
"Flip" Vertically rotate the video.
"Mirror" Horizontally rotate the video. Check options both if the Network Camera is
installed upside down.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 40 -
“Improve efficiency in the multi-user environment” Check this option to improve
efficiency in the multi-user environment when running in the low bandwidth
environment. But it will cause each connection slow a few minutes when connection
established.
<url>http://<IT350/IT350WNetworkCamera>/setup/video.vspx
<IT350/IT350WNetworkCamera>is the domain name or original IP address of the
IT350-IT350W Network Camera.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 41 -
Image Settings
Click on “Image Settings” to pop
up another window for tuning
"Brightness", “Contrast”, “Hue”
and "Saturation" for video
compensation.
Each field has eleven levels ranged
from -5 to +5. The User may press
“Preview” to fine-tune the image.
When the image is O.K., press
“Save” to set the image settings.
Click on “Restore” to recall the
original settings without
incorporating the changes.
CCD Settings
Click on “CCD Settings” button, the CCD settings window will pop up.
The default setting of the CCD is of auto-IRIS mode. Therefore the “Auto electronic
shutter” (AES) option will be fixed at 1/60 (1/50) second. Once the shutter is selected
as “Auto”, the IRIS of the CCD will become fixed. There are several selectable items for
AES. Faster electronic shutter helps seeing fast moving objects more clearly.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 42 -
“Auto tracking white
balance” is usually applied
when the Network Camera is
aiming outdoor. Adjusting the 9
levels of white levels can help
the camera capturing video with
correct colors. On the other
hand, select “White balance
control” will disable “Auto
tracking white balance”. It is
usually applied indoor to adjust
the video colors. The
administrator can set different
color temperatures
(3200K~8000K) to get correct
colors.
Checking “Low lux mode”
helps seeing object in poor
illuminative environment.
Turning on “Auto switch to B/W in low lux mode” together with “Low lux mode”
being checked, the video will become black and white automatically if the camera is
aiming at dark environment.
“Enable BLC” option is for back light compensation. Normally, objects in front of light
source are difficult to be seen, checking this option and adjusting “BLC sens level” can
help seeing the objects more clearly. The BLC sens level is about sensitivity of BLC
detection.
Clicking on “BLC Area Selection”, a selecting window will pop up. As the window
shows, the video is divided to 48 rectangle areas with the same size. Select the areas
to enable BLC, if no area is selected, checking “Enable BLC” option makes the video no
differences.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 43 -
The picture illustrates the corresponding areas of the selecting window in the real video.
“Select All” will check all the areas in the windows and “Clear All” will do vice versa.
“Save” button can set the selected areas for BLC.
In the CCD settings window, click on “Preview” to see the effect of changing the
options. Click on “Save” to set the CCD settings. Click on “Restore” to recall the
original settings without incorporating the changes.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 44 -
Audio
“Transmission mode” There are five options to select. For all the modes, only one
client can talk to the server at the same time.
“Full-duplex (Talk and listen simultaneously)” In this mode, the User can talk to
the server while listening sound from the server simultaneously.
“Half-duplex (Talk or listen, not at the same time)” In this mode, the User can
talk to the server or listen from the server, but not at the same time.
“Simplex – Talk only” In this mode, the User can only talk to the server.
“Simplex – Listen only” In this mode, the User can only listen from the server.
“Disable” In this mode, the audio is disabled in both directions.
“Send audio from the active client to all the other clients” In half duplex
transmission mode, select the option to talk to the server and broadcast your voice to
all the other clients.
“Improve audio quality in low bandwidth environment” If the IT350-IT350W
Network Camera works in versatile or low network bandwidth environment, the User
can check this option to improving audio quality by sacrificing some real-time
synchronization.
“Audio source” Select source from external or built-in microphone.
“Acoustic echo cancellation” In full-duplex mode, the server can play sound from
the client and receive sound from the environment and send to client. Since the sound
from the client is played by server, it will also be received by the server’s microphone
and send back to client. That is the client will hear its echo. Select this option can
prevent echo by sacrificing the video frame rate.
“Bit rate” There are three kinds of bit-rate for audio. 32Kbps and 24Kbps are suitable
for both music and speech like audio while 8Kbps are suitable for only speech like
audio.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 45 -
<url>http://<IT350/IT350WNetworkCamera>/setup/audio.vspx
<IT350/IT350WNetworkCamera>is the domain name or original IP address of the
IT350-IT350W Network Camera.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 46 -
Motion Detection
“Enable motion detection” Check this option to turn on motion detection.
Click on this button to add a new window. At most three windows can exist
simultaneously. Use the mouse to click, hold and drag the window frame to resize or the
title bar to move. Clicking on the ‘x’ at the upper right-hand corner of the window to
delete the window. Remember to save in order to validate the changes.
Click on this button to save the related settings. A graphic bar will rise or fall
depending on the image variations. A green bar means the image variation is under
monitoring level and a red bar means the image variation is over monitoring level.
When the bar goes red, the detected window will also be outlined in red. Going back to
the homepage, the monitored window is hidden but the red frame shows when motion
is detected.
“Window Name” The text will show at the top of the window.
“Sensitivity” This sets the endurable difference between two sequential images.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 47 -
“Percentage” This sets the space ratio of moving objects in the monitoring window.
Higher sensitivity and small percentage will allow easier motion detection.
<url>http://<IT350/IT350WNetworkCamera>/setup/motion.vspx
<IT350/IT350WNetworkCamera>is the domain name or original IP address of the
IT350-IT350W Network Camera.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 48 -
Camera Control
On the Camera Control page, there are two main function control areas:
Camera control area
The pan and tilt functions can be controlled with these buttons. The “Left” button aims
the camera to the left; the “Right”, “Up”, and “Down” buttons aim the camera
accordingly. The “Home” button aims the camera to the center.
“-” and “+” buttons beside “Zoom” control the zoom widely function and zoom
telescopically.
“-”, “Focus” and “+” in the same row control the focus near function, auto focus
function and focus far function.
“-”, “IRIS” and “+” in the same row set the aperture smaller, auto-IRIS and set
aperture bigger.
“Pan speed” This controls the range of the horizontal movement of the camera. The
greater the value, the greater angular movement when performing the “Left” or “Right”
functions.
“Tilt speed” This controls the range of the vertical movement of the camera. The
greater value, the greater angular movement when performing the “Up” or “Down”
functions.
“Zoom speed” This controls the range of the zooming. The greater the value, the
greater viewing angle changed.
“Focus speed” This controls the range of the focus adjustment. The greater the value,
the greater adjustment.
“Auto pan/patrol speed” This defines the speed of panning and patrol, the greater
the value, the faster the speed.
Preset function area
“Current position” If the User wants to save the current view as a preset location,
enters a name for each of the current video view at “Current position” and click on the
“Add” button. The camera allows for ten preset locations.
* The preset function is valid only in optical zoom mode.
“Preset position” This keeps a list for preset positions. Clicking on the “Delete”
button will remove the current selected position from the preset list.
“Set as home” Click on the button will command the IT350-IT350W Network Camera
to set the current aiming position as Home position. That is: when user click on the
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 49 -
“Home” control in Camera control area or after the IT350-IT350W Network Camera
rebooted, the aiming area will be moved to the current position.
“Default home” Click on the button will restore the “Home” definition to the original
position.
“Dwelling time” The value set here specifies:
1. The stop time of each preset location during auto patrol of the IT350-IT350W
Network Camera.
2. The stay time at the most left and the most right positions when the IT350-IT350W
Network Camera is doing auto panning.
“Enable IR control” Checking this box allows the Administrator to enable the IR
controller to move the aim of the camera. To allow controls only through URL
commands or web pages, leave this box unchecked.
“Zoom times display” Checking this box allows the Administrator to display the
zoom magnitude on the transmitted video. The information is described as the
following table:
Text displayed Meanings
Zoom X3 3 times optical zoom, the focal lens equals to 12.6 mm.
Zoom X10 xE2
10 times optical zoom with 2 times digital zoom, the focal lens
equals to 84 mm.
“Patrol selection” After the User has saved a list of preset positions, the “Preset
locations” box will also keep a list of the preset positions. And once the “Select>”
button is clicked, the “Selected location” box will keep a list of the patrol stops. The
“Remove” button removes the preset position from the patrol stops. The “UP”, “DOWN”
buttons adjust the order of the patrol stops. Several preset positions can be added to
the patrol stops. The camera can accept up to 20 patrol stops.
“Save” button
The button is valid for “Pan speed”, “Tilt speed”, “Tilt speed”, “Auto pan/patrol speed”,
“Enable IR control”, “Dwelling time” and “Patrol selections”. In other words, after
changing these settings, and the “Save” button is not clicked, the new setting of the
camera will not take effect.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 50 -
<url>http://<IT350/IT350WNetworkCamera>/setup/camctrl.vspx
<IT350/IT350WNetworkCamera>is the domain name or original IP address of the
IT350-IT350W Network Camera.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 51 -
Application Setup
Weekly Schedule
“Sun” ~ “Sat” Select the days of the week to perform the following operations.
“Snapshots begin at” Set the time to start operations.
“Snapshots stop at” Set the time to stop operations. Setting identical begin time and
stop time means 24-hour operation.
“All the time except for the above schedule” Invert the selected schedule. The
default setting of this option is checked.
“Snapshot file name prefix” Specify the prefix name for the snapshot file. For
example, if the prefix name of the snapshot file is “Network Camera”, the snapshot file
name will be Network Camera _20041116105638.jpg, that means the snapshot is
taken at 10:56:38, 2004/11/16.
Event Operation
“Delay second(s) before detecting next event” Set the time delay before
restarting to check on the triggering condition when the current condition is triggered.
“Send pre-event image(s) when event occurs” Specify how many pre-event
snapshot will be sent if events happen.
“Trigger condition” There are four conditions relative to the digital input and three
windows for motion detection. More than one condition can be selected at once. Select
the appropriate digital input condition that suits the characteristics of the external
device. “high”, “low” selects level-triggering via external voltage input. “rising”,
“falling” is for edge-triggering. There are three windows for motion detection each can
be assigned a name. If motion detection has not been set up, it will not be shown. If this
happens, clicking on “Motion detection” and a note will show to direct the User to the
configuration page for motion detection.
“Trigger action” There are four options for two types of action. More than one
condition can be selected at once. While choosing to trigger an output alarm, the digital
output will short both pins and complete the external device’s circuit. The normal state
is open. Either email or FTP can be used to command uploading snapshots. The
snapshot names will be “videopre.jpg”, “videotrg.jpg”, and “videopos.jpg”, respectively.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 52 -
They stand for the snapshots, before event, right upon event, and after event. The date
and time suffix may also be added as an option. Confirm the external mail or FTP server
settings in the network configuration.
“Reset output” Select and save this option to reset the external device at the digital
output to return to the original state.
Sequential Operation
“Snapshot interval” The IT350-IT350W Network Camera will send snapshots at the
specified intervals to the external server.
“Send snapshots by email” This selects the uploading method following the intervals
set above. The snapshot named “video.jpg” will be attached in the email with the
subject title “Periodic snapshots”.
“Send snapshots by FTP” The snapshots will be uploaded to the external FTP server
with the file name defined in the next option. This can also be used to refresh the
captured images stored in the external web server to build creative homepages.
“FTP put snapshots with date and time suffix” This option sets up the snapshot
capture date and time, which can be used to easily differentiate the snapshot file
names in either the sequential or event operation. For instance,
“pre_20060102030405.jpg” means the JPEG image was captured in the year 2006,
January 2nd, after 3 o’clock, 4 minute and 5 second as the previous frame in event
operation. If this suffix is omitted, the file named “video.jpg” on the external FTP server
will be refreshed at the specified interval.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 53 -
<url>http://<IT350/IT350WNetworkCamera>/setup/app.vspx
<IT350/IT350WNetworkCamera>is the domain name or original IP address of the
IT350-IT350W Network Camera.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 54 -
Viewing System Log
Click on the link on the configuration page to view the system log file. The content of
the file provides useful information about configuration and connections after system
boot-up.
Viewing System Parameters
Click on this link on the configuration page to view the entire system’s parameter set.
The content is the same as those in CONFIG.INI.
Factory Default
“Factory default”
Click on this link on the configuration page to restore factory default settings. Any
changes made so far will be lost and the system will be reset to the initial factory
settings. After clicking on the “Restore” button and make confirmation, the system will
restart and require the installer program to set up the network again.
“Calibrate”
Recalibrate the home position to the default center to recover the tolerance caused by some external
forces. This function is the same as the “Center” button on the Remote Controller. Please note that there
is no confirming message box after clicking on the “Calibrate” button, the
IT350-IT350W
Network
Camera will calibrate immediately.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 55 -
Remote Controller
IT350-IT350W Network Camera provides a remote controller to command the camera’s
pan/tilt and other functions. The direction control part provides the function as on the
main web page.
The Pan/Patrol/Stop functions are also the same as on the main web page.
“Auto Patrol” This button commands the camera to patrol between the preset
positions on the patrol list that was set on the “Camera control page”. After each patrol
cycle, the camera stops at the original staring position. “Auto Pan” This button
commands the camera to pan from the current position to the left most or right most
and back. After panning both horizontal end positions, the camera would stop at the
original starting position.
“Center” This calibrates the camera’s position to aim at the center as the camera boots
up.
“Stop” This stops the auto movements (auto pan & auto patrol) of the camera.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 56 -
Appendix
A. Troubleshooting
Status LED
After powering up, the Network Camera performs a self-diagnostic to detect any
hardware defects. The following table lists the LED patterns in general. In case of any
fatal error, the LED will blink in a pattern other than those below.
Condition LED color
During self-diagnostic after power on Blink in interchanged green and red
Ethernet signal is lost Red LED is off till Ethernet is detected
Before network is setup Steady green till IP address is confirmed
After network is setup Blink green every second
Any hardware failure Other patterns
Reset and Restore
At the left side of the IT350-IT350W Network Camera there
is a button hidden in the pinhole as shown in the picture. It
is used to reset the system or restore the factory default
settings. Sometimes resetting the system sets the system
back to normal state. If the system problems remain after
reset, restore the factory settings and install again.
RESET: Poke the wrench to click on the button.
RESTORE: 1. Poke the wrench to press on
the button continuously.
2. Wait for self-diagnostic to run twice.
3. Withdraw the wrench as soon as the
second self-diagnostic starts.
Restoring the factory defaults will
erase any previous settings. Reset or
restore the system after power on.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 57 -
B. Frequently Asked Questions
Q What if I forget my password?
A After the Administrator's password has been assigned, every access to the
IT350-IT350W Network Camera needs authentication. If you are one of the managed
users, you have to ask the Administrator for the password. If you are the Administrator,
there is no way to recover the root password except by restoring the factory default
settings. Refer to Appendix A for the procedures.
Q Why can I not watch video from the IT350-IT350W Network Camera after it is
authenticated?
A There are many possible scenarios regarding this problem,
1. If you have just installed the IT350-IT350W Network Camera and are unable to
watch the video, check if the heartbeat LED is blinking or the lens cap is off. If the
heartbeat LED is dim, perform the software installation again.
2. If the IT350-IT350W Network Camera is well installed and you are accessing the
IT350-IT350W Network Camera for the first time using Internet Explorer, adjust the
security level of Internet Explorer to allow installation of plug-ins.
3. If the problem still exists after adjusting, and the message over the image window is
showing "connecting", the network traffic may be too crowded.
4. It there is only “A” shown below the image, check the media options in client settings
containing video.
Q What is the plug-in for?
A The plug-in provided by the IT350-IT350W Network Camera is used to display motion
pictures and audio in Internet Explorer. If your system does not allow installation of any
plug-in software, the security level of the web browser may need to be lowered. It is
recommended that you consult your network supervisors in your office regarding
adjustment of the security level. Software installation may be regulated in some
offices.
Q Why is the timestamp different from the system time of my PC or notebook?
A The timestamp is based on the system time of the IT350-IT350W Network Camera.
It is maintained by a real-time clock inside and can be automatically synchronized with
the time-server if the IT350-IT350W Network Camera is connected to the Internet and
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 58 -
the function is enabled. Differences of several hours may result from the time zone
setting.
Q Can I install it on ceiling?
A Yes. There are flip and mirror options in video configuration page to correct the
images for upside down installation.
Q The image is not clear enough.
A Rotate the lens to adjust the focus after the IT350-IT350W Network Camera has
been installed in the proper position. The image settings and white balance can be fine
tuned to achieve the best visual effect. Also notice the power line frequency must
match the local utility to synchronize and minimize the effect of flickering florescent
lights.
Q Why does the image not refresh regularly?
A Some anti-virus programs filter the received web content. It takes time to perform
data examination and affect the streaming application such as IT350-IT350W Network
Camera. However, it only affects the HTTP mode of IT350-IT350W Network Camera. If
the network allows only HTTP mode, disable the web filtering function of the anti-virus
program temporarily. During this period, the User should be aware of the risk of
malicious network activity.
Q I have opened motion detection windows but it cannot work.
A If the motion detection windows are set up and names are given, check to see if the
function is checked on the first line. While it is enabled, adjust the sensitivity and
percentage to monitor the level indicator for best results.
Q I cannot hear any sound while watching.
A If there is "V" shown below the image, check the sound card in your PC and make
sure media options in client settings containing audio. If "AV" is shown, check the audio
source of the IT350-IT350W Network Camera, make sure you are using internal or
external microphone.
Q How many users are allowed to watch the IT350-IT350W Network Camera at the
same time?
A Too many users requesting the real-time multimedia content will jam the network.
For best results, the IT350-IT350W Network Camera is designed to accommodate a
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 59 -
maximum of ten (10) users to watch and listen for streaming video and audio at the
same time. For a larger number of users, it is recommended to build another web
server to host the retrieved contents from the IT350-IT350W Network Camera.
Q How fast is the video rate of the IT350-IT350W Network Camera?
A The MPEG4 codec engine can process up to 30 frames per second internally. However
the total performance is subject to many coefficients such as:
1. Network throughput,
2. Bandwidth share,
3. Number of users,
4. The complicated/detailed objects and movement in view,
5. The power of your PC or notebook that is responsible for displaying images.
In general, the transfer rate in a general local network environment can achieve over
200 kilobytes per second and approximately 10 to 20 pictures per second from a
regular environment.
Q How can I keep the IT350-IT350W Network Camera as private as possible?
A The IT350-IT350W Network Camera is designed for surveillance purposes and has
many flexible interfaces. The user authentication and special confirmation in
installation can keep the IT350-IT350W Network Camera from unauthorized access.
You may also change the HTTP port to a non-public number. The demo account is good
to separate guests from normal users and thus you can easily block guests anytime.
You can check the system log to examine any abnormal activities and trace the origins.
Q Why can I not access the IT350-IT350W Network Camera when I setup some options
in the application?
A Since the IT350-IT350W Network Camera is a "network camera", any incorrect
network settings will make it inaccessible. If this happens, restore the factory default
settings following the procedures in Appendix A.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 60 -
B. Cleaning the Lens
The Network Camera with Pan/Tilt/Zoom is a network camera with high quality lens.
When it is necessary to clean the lens, please follow these instructions:
Prepare cotton swabs and alcohol.
Moisten the cotton swab with alcohol.
Slightly clean the lens.
If the lens is still dirty, repeat 2~3 steps until it is cleaned. Change a clean cotton swab
if the old one is dirty or contains dirt that might scrape the lens.
Never touch the lens hard or roughly.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 61 -
C. Pan/Tilt/Zoom Data
unit tilt angle: 0.918 degree
The tile speeds of different auto pan/tile speeds.
auto tile speed 1: 1.65 degree/sec
auto tile speed 2: 6.59 degree/sec
auto tile speed 3: 8.24 degree/sec
auto tile speed 4: 10.98 degree/sec
auto tile speed 5: 16.47 degree/sec
auto tile speed 6: 32.95 degree/sec
tilt speed
zoom times
-5 -4 -3 -2 -1 0 1 2 3 4 5
1~3 0.23 0.46 0.92 1.84 3.67 5.51 6.43 7.34 8.26 9.18 10.10
4~7 0.23 0.23 0.46 0.92 1.84 2.75 3.21 3.67 4.13 4.59 5.05
8~100 0.23 0.23 0.23 0.46 0.92 1.38 1.61 1.84 2.07 2.30 2.52
unit pan angle: 1.29 degree
The pan speeds of different auto pan/tile speeds.
auto pan speed 1: 2.10 degree/sec
auto pan speed 2: 8.41 degree/sec
auto pan speed 3: 16.82 degree/sec
auto pan speed 4: 22.43 degree/sec
auto pan speed 5: 26.04 degree/sec
auto pan speed 6: 67.28 degree/sec
Pan
speed
zoom
times
-5 -4 -3 -2 -1 0 1 2 3 4 5
1~3 0.32 0.65 1.29 3.88 7.75 11.63 15.50 19.38 23.26 25.84 28.42
4~7 0.32 0.32 0.65 1.94 3.88 5.81 7.75 9.69 11.63 12.92 14.21
8~100 0.32 0.32 0.32 0.97 1.94 2.91 3.88 4.85 5.81 6.46 7.11
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 62 -
D. URL Commands of the IT350-IT350W
Network Camera
For some customers who already have their own web site or web control application,
the IT350-IT350W Network Camera can be easily integrated through convenient URLs.
This section lists the commands in URL format corresponding to the basic functions of
the Network Camera.
Overview
This section specifies the external HTTP based application programming interface. The
HTTP based camera interface provides the functionality to request a single image, to
control camera functions (PTZ, output relay etc.) and to get and set internal parameter
values. The image and CGI-requests are handled by the built in Web server.
Style Convention
In URL syntax and in descriptions of CGI parameters, a text in italic within angle
brackets denotes a content that is to be replaced with either a value or a string. When
replacing the text string also the angle brackets shall be replaced. An example of this is
the description of the name for the server, denoted with
<IT350/IT350WNetworkCamera> in the URL syntax description below, that is replaced
with the string myserver in the URL syntax example, also below.
URL syntax' are written with the “Syntax:" word written in bold face followed by a box
with the referred syntax as seen below. The name of the server is written as
<IT350/IT350WNetworkCamera>. This is intended to be replaced with the name of the
actual server. This can either be a name, e.g., "mywebcam" or "thecam.adomain.net"
or the associated IP number for the server, e.g., 192.168.0.220.
Syntax:
http://<servername>/cgi-bin/video.jpg
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 63 -
Description of returned data is written with "Return:" in bold face followed by the
returned data in a box. All data returned as HTTP formatted, i.e., starting with the
string HTTP is line separated with a Carriage Return and Line Feed (CRLF) printed as
\r\n.
Return:
HTTP/1.0 <HTTP code> <HTTP text>\r\n
URL syntax examples are written with "Example:" in bold face followed by a short
description and a light grey box with the example.
Example: request a single snapshot image
http://mywebserver/cgi-bin/video.jpg
General CGI URL Syntax and Parameters
CGI parameters are written in lower-case and as one word without any underscores or
other separators. When the CGI request includes internal camera parameters, the
internal parameters must be written exactly as they are named in the camera or video
server. The CGIs are organized in function related directories under the cgi-bin
directory. The file extension of the CGI is required.
Syntax:
http://<IT350/IT350WNetworkCamera>/cgi-bin/<subdir>[/<subdir>...]/<cgi>.<ext>
[?<parameter>=<value>[&<parameter>=<value>...]]
Example: Setting digital output #1 to high
http://mywebserver/cgi-bin/setparam.cgi?do1=h
Get Server Parameter Values
Note: This request require administrator access
Method: GET/POST
Syntax:
http://<IT350/IT350WNetworkCamera>/cgi-bin/admin/getparam.cgi?[<parameter>]
[&<parameter>…]
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 64 -
where the <parameter> should be <group>[_<name>] or <group>[.<name>] If you
do not specify the any parameters, all the parameters on the server will be returned. If
you specify only <group>, the parameters of related group will be returned.
When query parameter values, the current parameter value are returned.
Successful control requests returns paramter pairs as follows.
Return:
HTTP/1.0 200 OK\r\n
Content-Type: text/html\r\n
Context-Length: <length>\r\n
\r\n
<parameter pair>
where <parameter pair> is
<parameter>=<value>\r\n
[<parameter pair>]
<length>is the actual length of content.
Example: request IP address and it’s response
Request:
http://192.168.0.123/cgi-bin/admin/getparam.cgi?network_ipaddress
Response:
HTTP/1.0 200 OK\r\n
Content-Type: text/html\r\n
Context-Length: 33\r\n
\r\n
network.ipaddress=192.168.0.123\r\n
Set Server Parameter Values
Note: This request require administrator access
Method: GET/POST
Syntax:
http://<IT350/IT350WNetworkCamera>/cgi-bin/admin/setparam.cgi?
[nosync=<value>&]<parameter>=<value>
[&<parameter>=<value>…][&return=<return page>]
parameter value description
nosync
0, 1 Specifi
es that there should be no sync (write) of the
corresponding configuration file on flash. If parameter is
omitted, a sync write will occur.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 65 -
(note: this parameter must be put at begin of parameter
list)
<group>_<name>.
value to
assigned
Assign <value> to the parameter <group>_<name>..
return
<return
page>
Redirect to the page <return page>
after the parameter
is assigned. The <return page>
can be a full URL path or
relative path according the the current path. If you omit
this parameter, it will redirect to an empty page.
(note: The return page can be a general HTML
file(.htm, .html) or a server script executable (.vspx)
file. It can not be a CGI command. It can not have any
extra parameters. This parameter must be put at end of
parameter list)
Example: Set the IP address of server to 192.168.0.123
http://myserver/cgi-bin/admin/setparam.cgi?Network_IPAddress=192.168.0.123
Available Parameters on the Server
Group: System
NAME VALUE DESCRIPTION
hostname
(r/w)
<text string shorter
than 15 characters>
host name of server
0 Do not turn of the led indicator ledoff
(r/w)
1 Turn off the led indicator
0 Do not turn on automatic DO restoration
resetdo
(r/w)
1 Turn on automatic DO restoration
delayresetdo
(r/w)
1~999 Setup automatic DO restoration time
<yyyy/mm/dd>
year, month and date separated by
slash.
<keep> keep date unchanged
date
(r/w)
<auto>
Using NTP to sync date/time
automatically
<hh:mm:ss>
hour, minute and second separated by
colon.
<keep> keep date unchanged
time
(r/w)
<auto> Usin
g NTP to sync date/time
automatically
ntp
(r/w)
<domain name or IP
address>
NTP server
timezone
(r/w)
-12 ~ 12 time zone, 8 means GMT +8:00
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 66 -
updateinterval
(r/w)
0 ~ 2147483
0 to Disable automatic time adjustment,
otherwise, it means the seconds
between NTP automatic update interval.
serialnumber
(r)
<mac address>
12 characters mac address without
hyphen connected
firmwareversion
(r)
<text string shorter
than 39 characters>
The version of firmware, including
model, company, and version number
restore
(w)
0
Restore the system parameters to
default value. The value will be valid
after restart the server.
restart
(w)(restart)
0 ~ 65535
Restart the server after <value>
seconds.
H – NC connected with COMMON do<1~4>
(w)
<state>
L – NO connected with COMMON
H – NC connected with COMMON di<1~4>
(r)
<state>
L – NO connected with COMMON
supportscriptversion
(r)
<text string shorter
than 10 characers>
The version of supported
script/webpage
scriptversion
<text string shorter
than 10 characers>
The maximu
m version of currently
installed script/webpage
Group: Security
NAME VALUE DESCRIPTION
username_<1~
10>
(r/w)
<text string shorter
than 15 characters>
change user name.
userpass_<0~
10>
(r/w)
<text string shorter
than 15 characters>
change user’s password.
The UserPass_0 is root’s password.
userattr_<1~1
0>
(r/w)
[dido][|talk][|listen][|c
amctrl][|conf]
change user’s privilege. The privilege can be
the combination of
dido – Permit I/O access
talk – Permit to talk to server
listen – Permit to listen from server
camctrl – Permit to do camera control
conf –
Permit to change server’s
configuration
usercount
(r)
1 ~ 11
The current account number on the server
including root.
Group: Network
NAME VALUE DESCRIPTION
1 enable to get ipadd
ress, subnet, router,
dns1, dns2 from DHCP server at next reboot
resetip
(r/w)(restart)
0
Using preset ipaddress, subnet, router,
dns1, dns2
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 67 -
ipaddress
(r/w) (restart)
<IP address> IP address of server
subnet
(r/w) (restart)
<IP address> subnet mask
router
(r/w) (restart)
<IP address> default gateway
dns1
(r/w)
<IP address> primary DNS server
dns2
(r/w)
<IP address> secondary DNS server
smtp1
(r/w)
<domain name or IP
address>
primary SMTP server, max 40 characters
mailto1
(r/w)
<Recipient email
address>
mail recipient address, max 80 characters
mailuser1
(r/w)
<user account name on
1st smtp server>
mail recipient address, max 63 characters
mailpass1
(r/w)
<user password for
mailuser1>
mail recipient address, max 15 characters
smtp2
(r/w)
<domain name or IP
address>
secondary SMTP server, max 40 characters
mailto2
(r/w)
<text string shorter than
80 characters>
mail recipient address, max 80 characters
mailuser2
(r/w)
<user account name on
2nd smtp server>
mail recipient address, max 63 characters
mailpass2
(r/w)
<user
password for
mailuser2>
mail recipient address, max 15 characters
returnemail
(r/w)
<text string for return
email address>
return email address, max 80 characters
localftpport
(r/w)
<number less than
65535>
FTP port
ftp1
(r/w)
<domain name or IP
address>
primary FTP server
ftpport1
(r/w)
<number less than
65535>
primary FTP port
ftpuser1
(r/w)
<user account on 1
st
FTP
server>
user name for primary FTP server, max 63
characters
ftppass1
(r/w)
<password for
ftpuser1>
password for primary FTP server, max
15
characters
ftpfolder1
(r/w)
<target folder on 1
st
FTP
server>
upload folder in primary FTP server, max 40
characters
1 Enable passive mode of primary FTP server
ftppassmode1
(r/w)
0 Disable passive mode of primary FTP server
ftp2
(r/w)
<domain nam
e or IP
address>
secondary FTP server
ftpport2
(r/w)
<number less than
65535>
primary FTP port
ftpuser2
(r/w)
<user account on 2
nd
FTP server>
user name for secondary FTP server, max 63
characters
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 68 -
ftppass2
(r/w)
<password for
ftpuser2>
password for seco
ndary FTP server, max 15
characters
ftpfolder2
(r/w)
<target folder on 2
nd
FTP
server>
upload folder in secondary FTP server, max
40 characters
1 Enable passive mode of primary FTP server
ftppassmode2
(r/w)
0 Disable passive mode of primary FTP server
httpport
(r/w) (restart)
<number less than
65535>
HTTP port
videoport
(r/w)
<number less than
65535>
video Channel port for UDP
audioport
(r/w)
<number less than
65535>
audio Channel port for UDP
Group: Wireless (restart)
ssid
(r/w)
<text string short
er than
32 characters>
SSID for wireless lan settings
<default>
0 Infrastructure mode wlmode
(r/w)
1 Adhoc mode
1 ~ 11 Channel number of USA and Canada
<6>
1 ~ 13 Channel number of Euro
<6>
10 ~ 11 Channel number of Spain
<10>
10 ~ 13 Channel number of France
<10>
channel
(r/w)
1 ~ 14 Channel number of All
<6>
txrate
(r/w)
"NONE", "1M", "2M",
"5.5M", "11M", "6M",
"9M", "12M", "18M",
"24M", "36M", "48M",
"54M", "Auto" for
802.11g
Transmit rate in Mbps
<Auto>
Long Long preamble preamble
(r/w)
Short Short preamble
1 Enable data encription encrypt
(r/w)
0 Disable data encription
Auto Automatic mode
Open Open mode
authmode
(r/w)
Shared Shared mode
keylength
(r/w)
(64, 128) for 802.11g Key length in bits
<64>
keyformat
(r/w)
HEX Key1 ~ K
ey4 will be represented in HEX
format
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 69 -
ASCII
Key1 ~ Key4 will be represented in ASCII
format
keyselect
(r/w)
1 ~ 4 Default key number
<1>
key1
(r/w)
<text string shorter than
58 characters>
(depends on keyformat
& keylength)
WEP key1 for encryption
<0000000000>
key2
(r/w)
<text string shorter than
58 characters>
(depends on keyformat
& keylength)
WEP key2 for encryption
<0000000000>
key3
(r/w)
<text string shorter than
58 characters>
(depends on keyformat
& keylength)
WEP key3 for encryption
<0000000000>
key4
(r/w)
<text string shorter than
58 characters>
(depends on keyformat
& keylength)
WEP key4 for encryption
<0000000000>
domain
(r)
‘U’ for USA
‘C’ for Canada
‘E’ for Euro
‘S’ for Spain
‘F’ for France
‘I’ for Isrel
‘A’ for All
Wireless domain
Group: Video
NAME VALUE DESCRIPTION
text
(r/w)
<text string shorter than
15 characters>
enclosed caption
0 MPEG4 codectype
(r/w) (restart)
1 MJPEG
1 half
2 half x 2
3 normal
4 normal x 2
size
(r/w)
5 double
0 monochrome color
(r/w)
1 color
0 fix bit rate quality
(r/w)
1 fix quantization
quant 1 lowest quality of video
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 70 -
2 lower quality of video
3 normal quality of video
4 higher quality of video
(r/w)
5 highest quality of video
64000 set bit rate to 64K bps
128000 set bit rate to 128K bps
256000 set bit rate to 256K bps
384000 set bit rate to 384K bps
512000 set bit rate to 512K bps
768000 set bit rate to 768K bps
1000000 set bit rate to 1000K bps
bitrate
(r/w)
1200000 set bit rate to 1200K bps
1 set maximum frame rate to 1 fps
2 set maximum frame rate to 2 fps
3 set maximum frame rate to 3 fps
5 set maximum frame rate to 5 fps
10 set maximum frame rate to 10 fps
15 set maximum frame rate to 15 fps
20 set maximum frame rate to 20 fps
25 set maximum frame rate to 25 fps
maxframe
(r/w)
30 set maximum frame rate to 30 fps
1 flip image flip
(r/w)
0 normal image
1 mirror image mirror
(r/w)
0 normal image
Group: Audio
NAME VALUE DESCRIPTION
8000 set bitrate to 8K bps
24000 set bitrate to 24K bps
bitrate
(r/w)
32000 set bitrate to 32K bps
0 Full-duplex (Talk & Listen simultaneously)
1 Half-
duplex (Talk or Listen, not at the same
time)
2 Simplex – Talk only
transfermode
(r/w)
3 Simplex – Listen only
0 Do not send audio f
rom active client to all
other clients
sendclientaudio
(r/w)
1
Send audio from active client to all other
clients (only possible in Half-duplex)
0 Use external microphone in source (r/w)
1 Use build microphone
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 71 -
0 Disable low bandwidth environment support
lowbandwidth
(r/w)
1 Improve in low bandwidth environment
0 Disable enableaec
(r/w)
1
Group: Image
NAME VALUE DESCRIPTION
brightness
(r/w)
<-5 ~ 5>
Adjust brightness of image according to
mode settings.
saturation
(r/w)
<-5 ~ 5> Adjust saturation of image accordi
ng to
mode settings.
contrast
(r/w)
<-5 ~ 5>
Adjust contrast of image according to
mode settings.
hue
(r/w)
<-5 ~ 5>
Adjust hue of image according to mode
settings.
Preview
Apply the parameter of image but not
save
Restore Restore the last saved image parameters
mode
(w)
Save
Directly save the adjust image
parameters
Group: Motion
NAME VALUE DESCRIPTION
0 disable motion detection enabled
(r/w)
1 enable motion detection
0 disable motion window #1 win<1~3>_enabled
(r/w)
1 enable motion window #1
win<1~3>_name
(r/w)
<text string shorter
than 15 characters >
name of motion window #1
win<1~3>_left
(r/w)
0 ~ 352 for CCD
0 ~ 320 for CMOS
Left coordinate of window position.
win<1~3>_top
(r/w)
0 ~ 288 for PAL
0 ~ 240 for
NTSC & CMOS
Top coordinate of window position.
win<1~3>_width
(r/w)
0 ~ 352 for CCD
0 ~ 320 for CMOS
Width of motion detection window.
win<1~3>_height
(r/w)
0 ~ 288 for PAL
0 ~ 240 for
NTSC & CMOS
Height of motion detection window.
update
(w)
1 Update the above motion detecti
on
settings to take effect
Group: DDNS
NAME VALUE DESCRIPTION
enable 0, 1 Enable or disable the dynamic dns.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 72 -
(r/w)
provider
(r/w)
1 ~ 4 dyndns.org (dynamic)
dyndns.org (custom)
tzo.com
dhs.org
hostname
(r/w)
Text string shorter than
63 characters.
Your dynamic hostname.
usernameemail
(r/w)
Text string shorter than
63 characters.
Your user or email to login ddns service
provider
passwordkey
(r/w)
Text string shorter than
63 characters.
Your password or key to login ddns service
provider
update
(w)
0, 1
Update the above ddns settings to take
effect
Group: UPNP
NAME VALUE DESCRIPTION
enable
(r/w)
0, 1 Enable or disable the UPNP service.
Group: CAMCTRL
NAME VALUE DESCRIPTION
panspeed
(r/w)
-5 ~ 5 Pan speed
tiltspeed
(r/w)
-5 ~ 5 Tilt speed
zoomspeed
(r/w)
-5 ~ 5 Zoom speed
autospeed
(r/w)
-5 ~ 5 Auto pan speed
dwelling
(r/w)
0 ~ 9999 Time to dwelling when patrol
enableir
(r/w)
0, 1 Enable or disable the IR control
presetname_<0~9>
(r/w)
Text string shorter than
30 characters.
The name of preset location
presetpan_<0~9>
(r/w)
-127 ~ 127 The pan coordinate of preset location.
presettilt_<0~9>
(r/w)
-127 ~ 127 The tilt coordinate of preset location.
patrolname_<0~19>
(r/w)
Text string shorter than
30 characters.
The name of patrol location
Group: CCD
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 73 -
NAME VALUE DESCRIPTION
mode
(r/w)
save
Only specified “mode=save” can
make the parameters changed to
desired values.
autoiris
(r/w)
0 or 1
set 1 to enable auto iris, set 0 to
disable auto iris
irislevel
(r/w)
0~8 Set iris size, set bigger val
ue to set
bigger iris size
autoelectronicshutter
(r/w)
0~7
Set electronica shutter speed. set 0
for auto shutter, set 1 for fixed at
1/60 (1/50). Bigger value, faster
shutter.
ccd_whitebalancemode (r/w) 0~1 0: auto tracking white balance
1: white balance control
ccd_autotrackingwhitebalance
(r/w)
0~8
Adjust colors by setting different
levels. Set ccd_whitebalancemode
to 0 before setting this parameter.
ccd_whitebalancecontrol
(r/w)
0~8
Set different levels to meet different
color temperatures
(3200K~96
00K). Set
whitebalancemode to 1 before setting this
parameter.
lowluxmode
(r/w)
0 or 1 Turn off or on low lux mode
obwlowluxmode
(r/w)
0 or 1
Turn off or on black/white video in
low lux mode
enableblc
(r/w)
0 or 1
Disable or enable back light
compensation.
blcsenslevel
(r/w)
0~7 Set back light compensation level
blcarea(0)
(r/w)
0~255
First row in BLC area. 0 to indicate
disabling all sub windows. 255 to
indicate enabling all sub windows.
blcarea(1)
(r/w)
0~255 Second row in BLC area.
blcarea(2)
(r/w)
0~255 Third row in BLC area.
blcarea(3)
(r/w)
0~255 Fourth row in BLC area.
blcarea(4)
(r/w)
0~255 Fifth row in BLC area.
blcarea(5)
(r/w)
0~255 Sixth row in BLC area.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 74 -
Drive the Digital Output
Note: This request requires the privilege of I/O access control.
Method: GET/POST
Syntax:
http://<IT350/IT350WNetworkCamera>/cgi-bin/setdo.cgi?do1=<state>[&do2=<state>]
[&do3=<state>][&do4=<state>][&return=<return page>]
Where state is H, L. H means NC (normal close) connected with COMMON and L means
NO (normal open) connected with COMMON. The number of DO dependents on the
server type.
parameter Value description
H – NC connected with COMMON
do<num>
<state>
L – NO connected with COMMON
return
<return page> Redirect to the page <return page>
after the
parameter is assigned. The <return page>
can be
a full URL path or relative path according the the
current path. If you omit this parameter, it will
redirect to an empty page.
Example: Drive the digital output 1 to high and redirect to an empty page
http://myserver/cgi-bin/setdo.cgi?do1=H
Query Status of the Digital Input
Note: This request requires the privilege of I/O access control.
Method: GET/POST
Syntax:
http://<IT350/IT350WNetworkCamera>/cgi-bin/getdi.cgi?[di1][&di2][&di3][&di4]
If no parameter is specified, all the status of digital input will be returned.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 75 -
Return:
HTTP/1.0 200 OK\r\n
Content-Type: image/jpeg\r\n
Content-Length: <length>\r\n
\r\n
[di1=<state>]\r\n
[di2=<state>]\r\n
[di3=<state>]\r\n
[di4=<state>]\r\n
where <state> can be H or L.
Example: Query the status of digital input 1
Request:
http:// <IT350/IT350WNetworkCamera>/cgi-bin/getdi.cgi?di1
Response:
HTTP/1.0 200 OK\r\n
Content-Type: image/jpeg\r\n
Content-Length: 7\r\n
\r\n
di1=H\r\n
Capture Single Snapshot
Note: This request require normal user privilege
Method: GET/POST
Syntax:
http://<servername>/cgi-bin/video.jpg
Server will return the most up-to-date snapshot in JPEG format. The size and quality of
image will be set according to the JPEG settings on the server.
Return:
HTTP/1.0 200 OK\r\n
Content-Type: image/jpeg\r\n
[Content-Length: <image size>\r\n]
<binary JPEG image data>
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 76 -
Account Management
Note: This request requires administrator privilege
Method: GET/POST
Syntax:
http://<servername>/cgi-bin/admin/editaccount.cgi?
method=<value>&user=<name>[&pass=<value>][&privilege=<value>]
[&privilege=<value>][…][&return=<return page>]
parameter value description
add
Add an account to server. When using this
method, “username” field is necessary. It will use
default value of other fields if not specified.
delete Remove an account from
server. When using this
method, “username” field is necessary, and others
are ignored.
method
edit
Modify the account password and privilege. When
using this method, “username” field is necessary,
and other fields are optional. If not specified, it will
keep original settings.
username <name> The name of user to add, delete or edit
userpass <value>
The password of new user to add or that of old
user to modify. The default value is an empty
string.
<value> The privilege of user to add or to modify. T
he
privilege can be the addition of the following
values. Ex: A user with DI/DO access and listen
privilege can be assigned privilege as
privilege=dido&privilege=listen.
dido DI/DO access privilege
listen listen privilege
talk talk privilege
camctrl
camera control privilege (support only on PT(Z)
version)
privilege
conf configuration privilege
return <return page>
Redirect to the page
<return page>
after the
parameter is assigned. The <return page>
can be
a full URL path or relative path according the the
current path. If you omit this parameter, it will
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 77 -
redirect to an empty page.
System Logs
Note: This request require administrator privilege
Method: GET/POST
Syntax:
http://<servername>/cgi-bin/admin/syslog.cgi
Server will return the up-to-date system log.
Return:
HTTP/1.0 200 OK\r\n
Content-Type: text/plain\r\n
Content-Length: <syslog length>\r\n
\r\n
<system log information>\r\n
Configuration File
Note: This request requires administrator privilege
Method: GET/POST
Syntax:
http://<servername>/cgi-bin/admin/configfile.cgi
Server will return the up-to-date configuration file.
Return:
HTTP/1.0 200 OK\r\n
Content-Type: text/plain\r\n
Content-Length: <configuration file length>\r\n
\r\n
<configuration data>\r\n
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 78 -
Upload File (firmware)
Note: This request requires administrator privilege
Method: POST
Syntax:
http://<servername>/cgi-bin/admin/upload.cgi
Post data:
file=<file name>[&return=<return page>]\r\n
\r\n
<multipart encoded form data>
Server will accept the upload file named <file name> to be stored on the flash as
“flash.bin” and return with <return page> if indicated.
Camera Control
Note: This request requires camera control access privilege
Method: GET/POST
Syntax:
http://<servername>/cgi-bin/camctrl.cgi?
[move=<value>][&focus=<value>]
[&iris=<value>][&speedpan=<value>][&speedtilt=<value>][&speedzoom=<value>]
[&speedapp=<value>][&auto=<value>][&zoom=<value>][&return=<return page>]
parameter value description
home Move to camera to home position
up Move camera up
down Move camera down
left Move camera left
move
right Move camera right
speedpan -5 ~ 5 Set the pan speed
speedtilt -5 ~ 5 Set the tilt speed
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 79 -
speedzoom -5 ~ 5 Set the zoom speed
speedapp -5 ~ 5 Set the auto pan/patrol speed
pan Auto pan
patrol Auto patrol
auto
stop Stop camera
wide To zoom for larger view with current speed zoom
tele To zoom for farer view with current speed
auto To do auto focus
far To focus on farer distance
focus
stop To focus on nearer distance
auto Let the Network Camera control iris size
open Manually control the iris for bigger size
iris
stop Manually control the iris for smaller size
return <return page> Redirect to the page <return page>
after the
parameter is assigned. The <return page>
can be
a full URL path or relative path according to the
current path. If you omit this parameter, it will
redirect to an empty page.
Recall
Note: This request requires camera control access privilege
Method: GET
Syntax:
http://<servername>/cgi-bin/recall.cgi?
recall=<value>[&return=<return page>]
parameter value description
recall
Text string less
than 30
characters
One of the present positions to recall.
return <return page>
Redirect to the page
<return page>
after the
parameter is assigned. The <return page>
can be a full
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 80 -
URL path or relative path according to the current path.
If you omit this parameter, it will redirect to an empty
page.
System Information
Note: This request requires normal user privilege
Method: GET/POST
Syntax:
http://<IT350/IT350WNetworkCamera>/cgi-bin/sysinfo.cgi
Server will return the system information.
Return:
HTTP/1.0 200 OK\r\n
Content-Type: text/plain\r\n
Content-Length: <system information length>\r\n
\r\n
Model=<model name of server>\r\n
HostName=<host name of server>\r\n
Location=<video on text of server>\r\n
[Preset<0>=<first preset location>\r\n]
[Preset<1>=<second preset location>\r\n]
[...]
PTZEnabled=<PTZ status>\r\n
Where the <PTZ status> is a 32-bits integer, each bit can be set separately as follows:
Bit 0 =>Support camera control function 0(not support), 1(support)
Bit 1 => Build-in or external camera. 0(external), 1(build-in)
Bit 2 => Support pan operation. 0(not support), 1(support)
Bit 3 => Support tilt operation. 0(not support), 1(support)
Bit 4 => Support zoom operation. 0(not support), 1(support)
Bit 5 => Support focus operation. 0(not support), 1(support)
Preset Locations
Note: This request requires administrator access privilege
Method: GET/POST
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 81 -
Syntax:
http://<IT350/IT350WNetworkCamera>/cgi-bin/admin/preset.cgi?
[addpos=<value>][&delpos=<value>][&return=<return page>]
parameter value description
addpos
<Text string less
than 30
characters>
Add one preset location to preset list.
delpos
<Text string less
than 30
characters>
Delete preset location from preset list.
return <return page> Redirect to the page <return page>
after the
parameter is assigned. The <return page>
can be a full
U
RL path or relative path according to the current path.
If you omit this parameter, it will redirect to an empty
page.
IT350-IT350W User’s Manual
Intellisystem Technologies – http://www.intellisystem.it
- 82 -
E. Technical Specifications
- System
CPU: Trimedia PNX1300
RAM: 16MB SDRAM
ROM: 4MB FLASH ROM
- Networking
Protocol
TCP/IP, HTTP, SMTP, FTP, Telnet, NTP, DNS
UPnP, DDNS and DHCP
Physical
10BaseT Ethernet or 100BaseT Fast Ethernet
Wireless LAN
2.4GHz 802.11g/b
54/48/36/24/18/12/9/6/11/5.5/2/1Mbps
Coverage:
54Mbps:64m, 48Mbps:70m,
36Mbps:80m, 24/18/12/9/6Mbps:120m,
11Mbps:80m, 5.5Mbps:120m
2Mbps:200m, 1Mbps:300m
- Video
Algorithm supported
MPEG4 SP
MJPEG
Features
Adjustable image size, quality and bit rate
Timestamp and text overlay
3 motion detection windows
Resolution
Up to 30/25 frames at 176x120 or 176x144
Up to 30/25 frames at 352x240 or 352x288
Up to 15/12 frames at 704x480 or 704x576
- Camera specification
1/4 inch color CCD sensor
Typical: 1.5 Lux / F1.8
Low lux mode: 0.05 Lux/F1.8
AGC, AWB
Electronic shutter: 1/60(1/50) to 1/120,000
sec
Pixel Numbers: NTSC - 542(H)x496(V) or PAL
- 542(H)x586(V)
- Lens
Focal length 4.2~42mm
Aperture F1.8~2.9
10X optical zoom
10X digital zoom
- Audio
32Kbps, 24Kbps, 8Kbps
Acoustic echo cancellation
Full duplex audio communication
- Microphone
Omni-directional
Frequency: 20 – 20,000Hz
S/N ratio: more than 58dB
- General I/O
1 sensor input(max. 12VDC 50mA)
1 relay output(max. 24VDC 1A, 125VAC
0.5A)
- LED indicator
Dual color system status indicator
- Weight
NET. 450g
- Dimension
104.5mm(L) * 104.5mm(W) * 127mm(H)
- Power
Consumption: MAX 12 W
Universal switching power-supply included
Adapter input: 100-240VAC, 50/60Hz, 0.4A
Adapter output: 12VDC, 1.5A
- Operating Environment
Temperature: 0-40°C/32-104°F
Humidity: 85%RH
-EMI & Safety
CE, FCC
- Viewing system requirement
Operating System
Microsoft Windows 98SE/ME/2000/XP
Browser
Internet Explorer 5.x or above
Electromagnetic Compatibility (EMC)
This device compiles with FCC Rules Part 15. Operation is subject to the following two conditions.
•
This device may not cause harmful interference, and
•
This device must accept any interference received, including interference that may cause undesired
operation.
USA -
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a partial installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the seperation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-- Consult the dealer or an experienced radio/TV technician for help.
Shielded interface cables must be used in order to comply with emission limits.
Europe -
This digital equipment fulfills the requirement for radiated emission according to limit B
of EN55022/1998, and the requirement for immunity according to EN50082-1/1992.
Liability
Intellisystem Technologies S.r.l. cannot be held responsible for any technical or typographical
errors and reserves the right to make changes to the product and manuals without prior notice.
Intellisystem Technologies S.r.l. makes no warranty of any kind with regard to the material
contained within this document, including, but not limited to, the implied warranties of
merchantability and fitness for a particular purpose. All other company names and products are
trademark or registered trademarks of their respective companies.
Form any question and support please contact: Intellisystem Technologies S.r.l.
Support: info@intellisystem.it Web Site: http://www.intellisystem.it
Loading...