WIRELESS
150N
USB
ADAPTER
USER
MANUAL
MODEL 524698
INT-524698-UM-0112-03
WASTE ELECTRICAL & ELECTRONIC EQUIPMENT
(applicable in the European Union and other European countries with separate collection systems)
ENGLISH
This symbol on the product or its packaging indicates that this product shall not be treated as household waste.
this product, contact your local city office, your household waste disposal service or the shop where you
purchased this product. In countries outside of the EU: If you wish to discard this product, contact your local
authorities and ask for the correct manner of disposal.
DEUTSCH
Dieses auf dem Produkt oder der Verpackung angebrachte Symbol zeigt an, dass dieses Produkt nicht mit
dem Hausmüll entsorgt werden darf. In Übereinstimmung mit der Richtlinie 2002/96/EG des Europäischen
Parlamentsund des Rates über Elektro- und Elektronik-Altgeräte (WEEE) darf dieses Elektrogerät nicht im
normalen Hausmüll oder dem Gelben Sack entsorgt werden. Wenn Sie dieses Produkt entsorgen möchten,
bringen Sie es bitte zur Verkaufsstelle zurück oder zum Recycling-Sammelpunkt Ihrer Gemeinde.
ESPAÑOL
Este símbolo en el producto o su embalaje indica que el producto no debe tratarse como residuo doméstico.
De conformidad con la Directiva 2002/96/CE de la UE sobre residuos de aparatos eléctricos y electrónicos
(RAEE), este producto eléctrico no puede desecharse con el resto de residuos no clasificados. Deshágase de
este producto devolviéndolo al punta de venta o a un punta de recogida municipal para su reciclaje.
FRANÇAIS
Ce symbole sur Ie produit ou son emballage signifie que ce produit ne doit pas être traité comme un
déchet ménager. Conformément à la Directive 2002/96/EC sur les déchets d’équipements électriques et
électroniques (DEEE), ce produit électrique ne doit en aucun cas être mis au rebut sous forme de déchet
municipal non trié. Veuillez vous débarrasser de ce produit en Ie renvoyant à son point de vente ou au point
de ramassage local dans votre municipalité, à des fins de recyclage.
ITALIANO
Questo simbolo sui prodotto o sulla relativa confezione indica che il prodotto non va trattato come un rifiuto
domestico. In ottemperanza alla Direttiva UE 2002/96/EC sui rifiuti di apparecchiature elettriche ed
elettroniche (RAEE), questa prodotto elettrico non deve essere smaltito come rifiuto municipale misto. Si
prega di smaltire il prodotto riportandolo al punto vendita o al punto di raccolta municipale locale per un
opportuno riciclaggio.
POLSKI
Jeśli na produkcie lub jego opakowaniu umieszczono ten symbol, wówczas w czasie utylizacji nie wolno
wyrzucać tego produktu wraz z odpadami komunalnymi. Zgodnie z Dyrektywą Nr 2002/96/WE w sprawie
zużytego sprzętu elektrycznego i elektronicznego (WEEE), niniejszego produktu elektrycznego nie wolno
usuwać jako nie posortowanego odpadu komunalnego. Prosimy o usuniecie niniejszego produktu poprzez
jego zwrot do punktu zakupu lub oddanie do miejscowego komunalnego punktu zbiórki odpadów
przeznaczonych do recyklingu.
Disposal of Electric and Electronic Equipment
Instead, it should be taken to an applicable collection point for the recycling of electrical and
electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential
negative consequences to the environment and human health, which could otherwise be caused by
inappropriate waste handling of this product. If your equipment contains easily removable batteries
or accumulators, dispose of these separately according to your local requirements. The recycling of
materials will help to conserve natural resources. For more detailed information about recycling of
Thank you for purchasing the INTELLINET NETWORK SOLUTIONS™
Wireless 150N USB Adapter, Model 524698.
The Wireless 150N USB Adapter is a compact high-speed adapter that
allows you to connect your notebook or desktop PC to wireless networks
at faster speeds than ever before. Transfer or receive digital images,
videos and MP3 les by connecting to the wireless network with link
speeds of up to 150 Mbps using the latest in wireless technology. This
adapter is also compatible with 802.11b and 802.11g wireless access
points and wireless routers, giving you the exibility to start upgrading
your wireless network without the need to replace existing equipment.
With the easy-to-follow instructions in this manual, you’ll soon be able to
enjoy the benets of these additional features:
• Includes USB stand and extension cable (Hi-Speed USB 2.0)
• Supports WMM for increased multimedia data throughput
• Supports WEP (64/128 bit), WPA and WPA2 data encryption
• Supports Software AP function; Windows 2000, XP, Vista, 7
• Three-Year Warranty
FCC CertiFiCations
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
3
CAUTION: Any changes or modications not expressly approved by the
party responsible for compliance could void the user’s authority to operate
the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference; and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC rF radiation exposure statement
This equipment complies with FCC RF radiation exposure limits set forth
for an uncontrolled environment, and should be installed and operated with
a minimum distance of 2.5 cm (1 in.) between the radiator and your body.
SAR (specic absorption rate) compliance has been established in laptop
computer congurations with a USB port on the side near the center, as
tested in the application for certication, and can be used in laptops with
substantially similar physical dimensions, construction and electrical and
RF characteristics. Use in other devices, such as PDAs or lap pads, is
not authorized. This transmitter is restricted for use with the specic
antenna(s) tested in the application for certication. The antenna(s) used
for this transmitter must not be co-located or operated in conjunction with
any other antenna or transmitter.
r&tte ComplianCe statement
This equipment complies with all the requirements of Directive 1999/5/EC
of the European Parliament and the Council of March 9, 1999, on radio
equipment and telecommunication terminal equipment (R&TTE) and the
mutual recognition of their conformity. The R&TTE directive repeals and
replaces Directive 98/13/EEC (Telecommunications Terminal Equipment
and Satellite Earth Station Equipment) as of April 8, 2000.
eu Countries intended For use
The ETSI version of this device is intended for home/ofce use in Austria,
Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Italy,
Luxembourg, the Netherlands, Portugal, Spain, Sweden and the U.K., and
is also authorized for use in EFTA member states Iceland, Liechtenstein,
Norway and Switzerland. (EU countries not intended for use: none.)
4
TABLE OF CONTENTS
section page
Installation .......................................................................................... 6
Conguration ....................................................................................7
Network ........................................................................................ 9
Prole ................................................................................................10
Prole Conguration ............................................................. 12
Prole Authentication & Encryption (Security) ...................... 13
802.1x Setting/Certication ................................................... 16
802.1x Setting/CA Server ...................................................... 17
Statistics .................................................................................... 18
Advanced ................................................................................... 18
WMM.......................................................................................... 21
About.......................................................................................... 22
WPS Conguration .................................................................... 22
SoftAP ..................................................................................................... 26
Conguration .............................................................................26
Security Setting ......................................................................... 28
Access Control .......................................................................... 30
MAC Table ................................................................................. 31
Event Log ................................................................................... 31
Statistics .................................................................................... 32
About.......................................................................................... 32
Specications .................................................................................. 33
NOTE: The Windows XP screen images are similar for Windows 2000/
2003/Vista/7. Some images have been modied to t the format of this
user manual.
CONTENTS
5
INSTALLATION
1. Remove the adapter’s protective cap and
attach the antenna by securely screwing it
onto the antenna connector.
2. With your computer on, gently insert the
adapter into a USB 2.0 port. NOTE: If the
adapter doesn’t easily slide into the port,
ip the adapter over and try again.
3. The Welcome to the Found New Hardware Wizard screen will display
automatically. Click “Cancel” to continue.
4. Insert the included setup CD and run the “Setup.exe” program. Read
the license agreement that displays; select “I accept the terms of the
license agreement” and click “Next” to continue.
5. On the Setup Type screen, select “Install driver and INTELLINET WLAN
Utility.” Select
“Install driver
only” if you
prefer to use
the Windows
integrated
WLAN function.
Click “Next.”
6. In Windows XP, a “Microsoft Zero Conguration Tool” option displays. It’s
recommended
that the
alternative
“INTELLINET
Conguration
Tool” option be
selected, as it
features more
functions. Click
“N ext.”
6
IN STALLATIO N
7. Once the software installation is complete, select “Yes, I want to restart
my computer.” Once the reboot is complete, connect the Wireless N
USB Adapter to your computer. When the Found New Hardware
Wizard screen displays, select the option that allows Windows to
automatically search for the correct driver. Your adapter is now
installed.
CONFIGURATION
The conguration utility — which displays automatically once the adapter
is connected — is a powerful application that helps you congure the
adapter and monitor link status and statistics during the communication
process. This adapter will auto-connect to the wireless device that
has the better signal strength and no wireless security setting.
CONFIGURATION
7
The conguration utility appears as an icon in the Windows system tray
while the adapter is running. You can
open it by double-clicking on the icon.
In Windows XP, there is a “Windows Zero
Conguration Tool” option for setting up wireless clients. If you prefer to
use the conguration utility, there are two ways to switch to it instead of
using the Windows tool.
option 1
1. Right-click the utility icon in the
system tray and select “Use
INTELLINET Conguration
utility.”
option 2
1. Right-click the icon on the left side of the system tray and select “View
Available Wireless Networks.”
2. Click “Change advanced settings.”
8
CONFIGURATION
3. Uncheck “Use Windows
to congure my wireless
network settings” to
enable the utility for the
adapter. NOTE: If
“Wireless Zero
Conguration Tool” is
enabled, you can only
congure the advanced
settings or check the
link status and statistics
from the conguration
utility of the adapter.
NETWORK
When you open the conguration utility, the system scans all the channels
to nd access points/stations within the accessible range of the adapter
and automatically connect to the wireless device with the highest signal
strength. On the Network screen, all the networks nearby are listed.
You can change the connection to another network or add one of the
networks to your own prole list.
CONFIGURATION
9
Available Networks: This list shows all available wireless networks within
the range of the adapter. It also displays network information: SSID,
BSSID, Signal Strength, Channel, Encryption, Authentication and
Network Type. To connect to a network on the list, double-click the
item and the adapter will connect automatically to it.
Rescan: Click “Rescan” to collect the new information of all the wireless
networks nearby.
Connect: Click “Connect” to connect to the selected network.
Add to Prole: Click to add the selected network to the Prole list.
PROFILE
The Prole screen is for managing networks you connect to frequently.
You can add, delete, edit and activate a prole on this screen.
Prole List: The Prole List displays all the proles and their related
settings, including Prole Name, SSID, Channel, Authentication,
Encryption and Network Type.
Add, Edit, Delete: Click the corresponding button to add, edit or delete
the selected prole(s). Clicking “Add” displays the Add Prole screen,
which presents 1) Conguration and 2) Authentication and Encryption
(Security).
Activate: To display status information about your current wireless
connection, select the prole and click “Activate.” When a prole is
activated, the adapter will be initially connected to it.
10
CONFIGURATION
Status: This eld displays the SSID and MAC ID of the network the
adapter is connecting to.
Extra Info: This eld displays the link status.
Channel: This eld displays the number of the radio channel and the
frequency used for the networking.
Link Speed (Mbps): These elds display the transmission (Tx) and the
reception (Rx) rates of the network. The maximum transmission rate
is 54 Mbps.
Throughput (Kbps): These elds display the speed of data being
transmitted (Tx) and received (Rx).
Link Quality: This status bar indicates the quality of the link. The
higher the percentage, the better the quality.
dBm: To display the signal strength measured in dBm (decibels in
milliwatts), click this box on the Network screen (see Page 9).
Signal Strength: This bar shows the signal strength level. The higher
the percentage being shown in the bar, the more radio signal being
received by the adapter. This indicator helps to nd the proper position
of the wireless device for quality network operation.
Noise Strength: This bar displays the noise level in the wireless
environment.
CONFIGURATION
11
proFile ConFigur ation
Prole Name: Dene easily recognizable prole names to identify the
different networks.
SSID: The SSID (up to 32 printable ASCII characters) is the unique name
identied in a WLAN. The ID prevents the unintentional merging of
two co-located WLANs. If you specify an SSID for the adapter, then
only the device with the same SSID can interconnect to the adapter.
To add a nearby network to the prole list, pull down the menu to view
all the networks that can be selected.
Power Save Mode: The two power-saving functions are available only
when Network Type (see below) is set to “Infrastructure.”
• CAM (Constantly Awake Mode): With this selected, the adapter
will remain in an active mode.
• PSM (Power Save Mode): Enable the adapter in the power-save
mode when it is idle.
Network Type: Select from the drop-down menu.
• Infrastructure: This operation mode requires the presence of an
802.11 access point. All communication is done via the AP or router.
• Ad-Hoc: Select this mode to connect to another wireless station in
the wireless LAN network without using an access point or router.
Tx Power: To lower the transmit power of the adapter to reduce the power
used by the system, select a lower percentage from the drop-down
menu. NOTE: A lower power level will result in lower signal strength
and reduced coverage range.
12
CONFIGURATION
RTS Threshold: This is the minimum packet size required for an RTS
(request to send). For packets smaller than this threshold, an RTS is
not sent and the packet is transmitted directly to the wireless network.
Select a setting within a range of 0 to 2347 bytes. NOTE: A minor
change is recommended.
Fragment Threshold: This value denes the maximum size of packets;
any packet size larger than the value will be fragmented. If you’ve
decreased this value and experience high packet-error rates, you
can increase it again, but it will likely decrease overall network
performance. Select a setting within a range of 256 to 2346 bytes.
NOTE: A minor change is recommended.
proFile authentiCation and enCryption (seCurity)
Authentication Type: This pull-down menu setting has to be consistent
with the wireless networks that the adapter is intended to connect.
• Open: No authentication is needed within the wireless network.
• Shared: Only wireless devices using a shared key (WEP key
identied) are allowed to connect to each other.
• LEAP: This is a pre-EAP, Cisco-proprietary protocol with many of
the features of EAP protocols. Cisco controls the ability of other
vendors to implement this protocol, so it should be selected for use
only when a limited vendor choice for client, access point and server
products is not a concern. When you’ve set up LEAP authentication,
you need to enter the username and password of your computer.
• WPA: WPA provides a scheme of mutual authentication using either
IEEE 802.1x/Extensible Authentication Protocol (EAP) authentication
CONFIGURATION
13
or pre-shared key (PSK) technology. It provides a high level of
assurance to enterprises, small businesses and home users that
data will remain protected and that only authorized users may access
their networks. For enterprises that have already deployed IEEE
802.1x authentication, WPA offers the advantage of leveraging
existing authentication databases and infrastructure.
• WPA-PSK: This is a special mode designed for home and small
business users who do not have access to network authentication
servers. In this mode, known as Pre-Shared Key, you manually
enter the starting password in your access point or gateway, as
well as in each wireless station in the network. WPA-PSK takes
over automatically from that point, keeping unauthorized users who
don’t have the matching password from joining the network, while
encrypting the data traveling between authorized devices.
• WPA2: Like WPA, WPA2 supports IEEE 802.1x/EAP authentication,
or PSK, technology. It also includes a new advanced encryption
mechanism using the Advanced Encryption Standard (AES). AES is
required for corporate or government users. The difference between
WPA and WPA2 is that WPA2 provides data encryption via AES. In
contrast, WPA uses the Temporal Key Integrity Protocol (TKIP).
• WPA 2-PSK: This is also for home and small business use. The
difference between WPA-PSK and WPA2-PSK is that WPA2-PSK
provides data encryption via the AES. In contrast, WPA-PSK uses
the Temporal Key Integrity Protocol (TKIP).
• WPA-NONE: This is dened for Ad Hoc mode and behaves like
WPA-PSK (WPA-PSK is only dened for Infrastructure mode). The
user manually enters the Pre-Shared Key in each wireless station
in the network, and WPA-NONE controls unauthorized users who
don’t have the matching Pre-Shared Key from joining the network.
It also encrypts the data traveling between authorized devices.
802.1x Setting: When Authentication Type is set to “Open,” “Shared,”
“WPA” or “WPA2,” you can also enable IEEE 802.1x Setting to use the
authentication server or certication server to authenticate client users.
NOTE: See the two separate 802.1x Setting sections below for details.
Encryption: Select from the drop-down menu.
• None: Disables the encryption mode.
14
CONFIGURATION
• WEP: Enables the WEP Data Encryption. When the item is selected,
you need to continue setting the WEP Encryption keys.
• TKIP: The Temporal Key Integrity Protocol changes the temporal key
every 10,000 packets (a kind of message transmitted over a network.)
This ensures much greater security than the standard WEP security.
• AES: AES has been developed to ensure the highest degree of
security and authenticity for digital information. It’s the most advanced
solution dened by IEEE 802.11i for security in the wireless network.
NOTE: All devices in the network should use the same encryption
method to ensure the security of communications.
WPA Pre-Shared Key: The WPA-PSK key can be 8 to 64 characters in
length and can be letters or numbers. This same key must be used on
all the wireless stations in the network.
WEP Key (Key#1– 4): WEP keys are used to encrypt data transmitted
in the wireless network. There are two types of key length: 64-bit and
128-bit. Assign a default encryption key (Key#1 to Key#4) by clicking
on the corresponding radio button. To ll in each text eld:
• 64-bit: Input 10-digit hex values (in the A-F, a-f and 0-9 range) or
5-digit ASCII characters (a-z and 0-9) as the encryption keys.
For example: “0123456aef“ or “test1.”
• 128-bit: Input 26-digit hex values (in the A-F, a-f and 0-9 range) or
13-digit ASCII characters (“a-z” and “0 -9”) as the encryption keys.
For example: “01234567890123456789abcdef“ or “administrator.”
The IEEE 802.1X specication describes a protocol that can be used for
authenticating both clients (802.1x Setting/Certication below) and servers
(802.1x Setting/CA Server below) on a network. The authentication
algorithms and methods are those provided by the Extensible Authentication
Protocol (EAP), a method of authentication that has been in use for a
number of years on networks that provide Point-to-Point Protocol (PPP)
support (as many Internet service providers and enterprises do). EAP
runs before network layer protocols transmit data over the link.
When an AP acting as an authenticator detects a wireless station on the
LAN, it sends an EAP request for the user’s identity to the device. In
turn, the device responds with its identity, and the AP relays this identity
to an authentication server (typically an external R ADIUS server).
CONFIGURATION
15
RADIUS
Server
Windows 2000 IAS
Access Point
RADIUS
Client
1
2
3
4
IEEE 802.1x Access Client RADIUS Client R ADIUS Server
1
2
1 Client requests to log in to the network 3 Username and password sent to R ADIUS server
2 Log in with username and password 4 User login to the LAN approved or denied
3
4
802.1x setting/CertiFiCation
EAP Method: The EAP authentication protocols supported by this
adapter require that settings be consistent with the wireless access
points or routers that the adapter is intended to connect.
• PEAP & TTLS: These protocols are similar and easier to use than
TLS (below) in that they specify a stand-alone authentication protocol
to be used within an encrypted tunnel. TTLS supports any protocol
within its tunnel, including CHAP, MS-CHAP, MS-CHAPv2, PAP and
EAP-MD5. PEAP species that an EAP-compliant authentication
protocol be used; this adapter supports EAP-MSCHAP v2, EAP-TLS/
Smart Card and Generic Token Card. The client certicate is optional.
• TLS/Smart Card: This is the most secure of the EAP protocols, but
isn’t easy to use: It requires that digital certicates be exchanged in
16
CONFIGURATION
the authentication phase. The server presents a certicate to the
client and, after validating the server’s certicate, the client presents
a client certicate to the server for validation.
Session Resumption: Click/check the box to activate or de-activate.
ID/Password: Enter the password as the identity for the server.
Client Certication: A client certicate is required for TLS, but is
optional for TTLS and PEAP. This forces a client certicate to be
selected from the appropriate Windows Certicate Store and made
available to the R ADIUS server for certication.
Tunneled Authentication/Protocol: When the authentication type is
PEAP or TTLS, select a protocol for building the encrypted tunnel.
Tunnel Authentication: Select one of three options from the drop down menu: “EAP-MSCHAPv2,” “EAP-TLS/Smart card” or “Generic
Token Card.”
802.1x setting/Ca server
Use certicate chain: When the Extensible Authentication Protocol
(EAP) authentication type — such as TLS, TTLS or PEAP — is
selected and requires certication to tell the client what credentials to
accept from the authentication server in order to verify the server, you
need to enable this function. Choose the preferred server from the
drop-down menu to issue the certicate. If “Any Trusted CA” is
selected, any CA (certication authority) on the list (which is provided
by the Microsoft Certicate Store) is permitted.
Allow intermediate certicates: A server designates an issuer as a
trusted root authority by placing the issuer’s self-signed certicate,
CONFIGURATION
17
which contains the issuer’s public key, into the trusted root certication
authority certicate store of the host computer. Intermediate or
subordinate certication authorities are trusted only if they have a
valid cer tication path from a trusted root certication authority.
Server Name: Enter the authentication server name.
Server name must match exactly: When selected, the server name
must exactly match the server name found on the certicate.
Domain name must end in specied name: When this is selected,
the server name eld identies a domain. The certicate must use a
server name belonging to this domain or one of its sub-domains (e.g.,
zeelans.com, where the server is blueberry.zeelans.com), but it may
be any name used in the certicate name eld.
STATISTICS
This screen enables you to view/compare the transmit and receive
statistical information of the connection. To reset the counters, click
“Reset Counter.”
ADVANCED
This screen enables you to congure more advanced settings, such as
the wireless mode and the protection mode.
Wireless Mode: Select from the drop-down menu.
• 802.11 B/G mix: If you have a mix of 802.11b and 802.11g wireless
stations in your network, it is recommended that the adapter be set
18
CONFIGURATION
to this mode. This mode is also the default setting.
• 802.11 B only: Though the adapter is compatible with both 802.11g
and 802.11b wireless stations, if there are only 802.11b wireless
stations in the network, you can set the adapter to this mode.
Ad Hoc Wireless Mode: When the adapter is set in Ad Hoc (Peer to
Peer) mode, you can designate the wireless connection mode for the
Ad Hoc network.
• Only B: Though the adapter is compatible with both 802.11g and
802.11b wireless stations, if there are only 802.11b wireless stations
in the network, you can set the adapter to this mode.
• B/G Mixed: If you have a mix of 802.11b and 802.11g wireless
stations in your network, it is recommended that the adapter be set
to this mode. This mode is also the default setting.
• Only G: Though the adapter is compatible with both 802.11g and
802.11b wireless stations, if there are only 802.11g wireless stations
in the network, you can set the adapter to this mode.
Wireless Protection: If you have a mix of 802.11b and 802.11g wireless
stations in the network, it’s recommended that you enable the protection
mechanism, which can decrease the rate of data collisions between
802.11b and 802.11g wireless stations. When the protection mode is
enabled, the throughput of the adapter will be a little lower.
• Auto: Depending on the status of the network, this automatically
disables/enables the protection mode.
• On: Always enables the protection mode.
• Off: Always disables the protection mode.
CONFIGURATION
19
Tx Rate: There are several options in the drop-down menu: “Auto” and a
range of speeds from “1 Mbps” to “54 Mbps.” When “Auto” is selected,
the device automatically chooses the most suitable transmission rate.
The higher the data rate designated in the network, the shorter the
distance allowed between the adapter and the wireless stations.
Enable Tx Burst: This enables the adapter to deliver better throughput
in the same period and environment.
Enable TCP Window Size: The TCP window is the amount of data a
sender can deliver on a particular connection before it gets an
acknowledgment back from the receiver that it has gotten some of it.
When the router or AP the adapter is connecting to has set up the
TCP window, you can enable the parameter to meet the data size for
the router or AP connection. The larger the TCP window, the better
the performance.
Fast Roaming at [-70] dBm: To fast roam to a nearby network without
interrupting the wireless connection (such as a multimedia application
or a voice call), you can set this parameter. The adapter will fast roam
when the receive sensitivity (signal strength) is below the value entered.
Show Authentication Status Dialog: Select to display.
Select Your Country Region Code: Channel availability varies from
country to country; for example, USA (FCC) channels are 1-11, while
Europe (ETSI) channels are 1-13.
Enable CCX: Cisco Compatible Extensions, for radio monitoring and
fast roaming.
Turn on CCKM: During normal operation, LEAP-enabled client devices
mutually authenticate with a new AP by performing a complete LEAP
authentication, including communication with the main RADIUS server.
When a wireless LAN is congured for fast re-association, however,
LEAP-enabled client devices roam from one access point to another
without involving the main server. Using Cisco Centralized Key
Management (CCKM), an access point congured to provide wireless
domain services (WDS) takes the place of the RADIUS server and
authenticates the client so quickly that there is no perceptible delay
in voice or other time-sensitive applications.
Enable Radio Measurement: When this parameter is enabled, the Cisco
20
CONFIGURATION
AP can run the radio monitoring through the associated CCX-compliant
clients to continuously monitor the WLAN radio environment and
discover any new APs that are transmitting beacons.
Non-Serving Channel Measurements: The Cisco access point can
perform monitoring measurements through the CCX-compliant clients
on the non-serving channels when this parameter is enabled.
Limit [xxx] milliseconds (0-2000): This setting limits the channel
measurement time. The default value is 250 milliseconds.
Turn off RF: Click to turn off the radio of the adapter; click again to turn
it back on.
WMM
This screen enables you to congure WMM (Wi-Fi Multimedia) and
other QoS settings, such as Power Save and Direct Link Setup.
WMM Enable: Click the check box (then click “Apply”) to enable the WMM
function, which then lets you congure the WMM Power Save and
Direct Link Setup functions.
• WMM – Power Save Enable: Click the check box to enable, then
click “Setting” to further congure the function as “AC_BK,” “AC_BE,”
“AC_VI” or “AC_VO.”
• Direct Link Setup Enable: Click the check box to enable, then click
“Apply” to further congure the function (all within the Direct Link panel).
- MAC Address: Specify the MAC address of the client adapter you
CONFIGURATION
21
want to direct link to and click “Apply” to add to the DLS Status
table (below).
- Timeout Value: Specify the timeout value for the direct link being
set up.
ABOUT
On this screen, you can click the hyperlink for information on the wireless
chipset manufacturer. Basic information about the utility (driver, EEPROM
version, etc.) also displays, as do various addresses for quick reference.
NOTE: This adapter features Turbo Mode, which delivers a higher
throughput than IEEE 802.11g standard (up to 54 Mbps) by compressing
data and decreasing the wait time for sending data to routers or access
points. Turbo Mode is enabled automatically without any conguration.
WPS CONFIGURATION
The adapter supports WPS (Wi-Fi Protected Setup), allowing connection
to wireless APs that also support WPS without complicated procedures.
Two WPS conguration methods are available when you click to display
this screen: PBC (push-button conguration) and PIN Code (an option
for older APs not equipped with the WPS push button but which may be
transformed into a WPS-enabled access point through a rmware upgrade).
22
CONFIGURATION
pBC (push-Button ConFiguration)
1. From the “Cong Mode” drop-down menu, select “Enrollee,” then press
the WPS button (or whichever button is used to activate the WPS
Standby mode) on your wireless access point. NOTE: Refer to your
wireless access point’s user manual for the specic procedure(s).
Alternatively, you can select “Registrar,” in which case this adapter
will wait for other WPS-enabled access points to send WPS pairing
requests. NOTE: Refer to your wireless access point’s user manual
to understand how to send WPS requests.
2. Before you start to establish the wireless connection using WPS, you
can click “Rescan” to search again for WPS-enabled access points
near you in order to make sure the WPS function of your access point
is activated. All access points with the WPS function enabled will be
displayed in the WPS AP List eld. If the access point you want to
connect to isn’t listed, click “Rescan” a few more times.
3. Begin the PBC pairing procedure on the access point side (again,
refer to your access point’s manufacturer’s instructions), then click
“PBC” to establish a wireless connection via WPS. NOTE: This may
require as much as a full minute to complete. When the “WPS status
is connected successfully” message displays, the connection between
the adapter and the access point has been successfully established
through WPS and information about the access point you connected
to will be displayed.
CONFIGURATION
23
4. Should the WPS function fail (as indicated on the following screen,
which shows that WPS pairing failed because no WPS-enabled AP
was found), you may nd that clicking “PBC” a few more times will
result in a connection. When an access point is connected, you can
click “Disconnect” to break the connection, or you can highlight/select
another WPS-enabled wireless access point when more than one is
found, then click “Connect” to establish that connection. You can also
click “Rotate” to select the next access point on the list for connection.
Information: Click to display a pop-up window describing a selection.
Detail: Click to show details of a selected WPS-enabled access point.
Export Prole: Click to save a highlighted connection on the list as a
prole, which will display on the WPS Prole list and which can be
retrieved in the Prole menu.
Delete: Delete the selected WPS-enabled access point from the list.
WPS Associate IE: Select to send the association request with WPS
IE (Information Element) during WPS setup. This is optional: You can
use the default value if you don’t know what will be affected.
WPS Probe IE: The Wireless Provisioning Services Information Element
(WPS IE) makes it easier to connect to public Wi-Fi networks you’ve
not previously connected to. Your computer must have the WPS IE
update for Windows XP SP2 installed in order to use the function.
This is optional: You can use the default value if you don’t know what
will be affected.
Auto: See PIN Code below.
24
SoftAP
pin Code
1. Enter the 8-digit PIN code of the adapter (highlighted below) in your
wireless access point as the WPS PIN code. NOTE: Refer to your
wireless access point’s user manual for instructions. If you have a
problem with the PIN code provided here, click “Renew” to get a new
PIN code.
2. Click “PIN.” After a short period (up to a minute), if a wireless access
point with the correct PIN code is found, you’ll be connected to that
access point. NOTE: As with PBC, you may need to click “PIN” a
number of times to make a connection. (It helps to conrm you’ve
entered the correct PIN code into the AP.)
Information: Click to display a pop-up window describing a selection.
Detail: Click to show details of a selected WPS-enabled access point.
Export Prole: Click to save a highlighted connection on the list as a
prole, which will display on the WPS Prole list and which can be
retrieved in the Prole menu.
Delete: Delete the selected WPS-enabled access point from the list.
WPS Associate IE: Select to send the association request with WPS
IE (Information Element) during WPS setup. This is optional: You can
use the default value if you don’t know what will be affected.
WPS Probe IE: The Wireless Provisioning Services Information Element
(WPS IE) makes it easier to connect to public Wi-Fi networks you’ve
not previously connected to. Your computer must have the WPS IE
update for Windows XP SP2 installed in order to use the function.
SoftAP
25
This is optional: You can use the default value if you don’t know what
will be affected.
Auto: When selected, the wireless access point to be connected will
be selected automatically.
SoftAP
This adapter can run as a
wireless access point (AP).
Right-click the conguration
utility icon on the Windows
system tray and select
“Switch to AP Mode” to activate the SoftAP function.
CONFIGURATION
This screen enables you to congure the AP connection setting, the
Country Region Code and other advanced functions.
SSID: The SSID (up to 32 printable ASCII characters) is the unique
26
SoftAP
name identied in a wireless LAN. The ID prevents the unintentional
merging of two co-located WLANs. The default SSID of the AP is
“SoftAP-X.” (“X” is the last number of this adapter’s MAC address).
Wireless adapters connected to the access point should be set up
with the same SSID as the AP.
Channel: Select the number of the radio channel used by the access
point. Any wireless adapters connected to the AP should be set up
with the same channel.
Wireless Mode: Selects the wireless mode supported by the AP.
Use MAC Address: Click to create a unique SSID based on the adapter’s
MAC address.
Security Setting: Click to further congure WLAN authentication and
security settings. (See the separate Security Setting section below.)
Country Region Code: Channel availability varies from country to
country; e.g., USA (FCC) channels are 1-11, while Europe’s (ETSI) are 1-13.
Beacon (ms): Dene the time between beacons (default is 100 ms.)
Tx Power: To lower the transmit power of the AP to reduce the power
used by the system, select a lower percentage from the drop-down
menu. NOTE: A lower power level will result in lower signal strength
and reduced coverage range.
Idle Time: Select the idle time for the wireless access point. The default
value is 300, and normally there is no need to change it.
No forwarding among wireless clients: Enable to prevent wireless
clients connected to this AP from sharing information with each other.
Hide SSID: When this box is checked, the AP will not appear in the site
survey list of any wireless clients, meaning only the wireless clients
set with the same SSID can connect to the AP. This prevents the AP
being connected to by unauthorized users.
Allow BW 40 MHz: Check this box to allow BW 40 MHz capability.
Tx Burst: Check this box to accelerate the data transmit rate. It may not
work with all wireless access points and wireless devices.
Default: Click to use the default value.
Apply: Click to apply the setting change(s).
SoftAP
27
SECURITY SETTING
This screen — accessed by clicking “Security Setting” on the previous
SoftAP Conguration screen — lets you to congure the authentication
mode and encryption algorithm used within the AP.
Pre-Shared Key
Authentication Type: Four types of authentication mode are
supported and presented in the drop-down menu.
• Open: No authentication is needed within the wireless network.
• WPA-PSK: This is a special mode designed for home and small
business users who do not have access to network authentication
servers. In this mode, known as Pre-Shared Key, you manually
enter the starting password in your access point or gateway, as well
as in each wireless station in the network. WPA-PSK automatically
takes over from that point, keeping unauthorized users who don’t
28
SoftAP
have the matching password from joining the network, while
encrypting the data traveling between authorized devices.
• WPA 2-PSK: This is also for home and small business use.
• WPA- PSK /WPA 2-PSK: When selecting this mode, the AP supports
both WPA-PSK and WPA2-PSK.
Encryption Type: Five options are available in the drop-down menu.
• Not Use: Disables the encryption mode.
• WEP: Enables WEP Data Encryption. When the item is selected,
continue setting the WEP Key.
• TKIP: The Temporal Key Integrity Protocol changes the temporal
key every 10,000 packets (a kind of message transmitted over a
network.) This ensures much greater security than standard WEP
secu rity.
• AES: Advanced Encryption Standard was developed to provide the
highest degree of security and authenticity for digital information.
It’s the most advanced solution dened by IEEE 802.11i for security
in a wireless network.
• BOTH: In this mode, the AP supports both TKIP and AES.
WPA Pre-Shared Key: The WPA-PSK key can be 8 to 64 characters in
length and can be letters or numbers. This same key must be used on
all the wireless stations in the network.
Group Rekey Interval: This function is available when using WPA-PSK
and WPA2-PSK encryption algorithms.
WEP Key (Key#1– 4): WEP keys are used to encrypt data transmitted
in the wireless network. There are two types of key length: 64-bit and
128-bit. Assign a default encryption key (Key#1 to Key#4) by clicking
on the corresponding radio button. To ll in each text eld:
• 64-bit: Input 10-digit hex values (in the A-F, a-f and 0-9 range) or
5-digit ASCII characters (a-z and 0-9) as the encryption keys.
For example: “0123456aef” or “test1.”
• 128-bit: Input 26-digit hex values (in the A-F, a-f and 0-9 range) or
13-digit ASCII characters (“a-z” and “0-9”) as the encryption keys.
For example: “01234567890123456789abcdef“ or “administrator.”
Show Password: The password will be displayed in clear text instead
of with asterisks.
SoftAP
29
ACCESS CONTROL
This screen lets you congure the access control policy used within the
access point.
MAC Table
Access Policy: Select from the drop-down menu.
• Disable: Disables the MAC address ltering function.
• Allow All: Only wireless adapters with a MAC address on the access
list can connect to the AP.
• Reject All: Wireless adapters with a MAC address on the access
list will be prevented from connecting to the AP.
MAC Address: This is the unique 12-digit hexadecimal identication for
hardware devices in the network.
Access List: Displays all the MAC address that have been added.
• Add: Add the MAC address to the access list.
• Delete: Delete the selected MAC address from the access list.
• Remove All: Remove all MAC addresses from the access list.
Apply: Click to apply the setting change(s).
30
SoftAP
MAC TABLE
This screen displays details of the wireless adapters connected to the AP.
MAC Table
MAC Address: The addresses of wireless adapters connected to the AP.
AID: The Association ID of the current connection.
Power Saving Mode: The supporting status of the power saving mode
of the connected wireless adapter.
EVENT LOG
This screen displays event times and messages. Click “Clear” to remove
displayed information.
MAC Table
SoftAP
31
STATISTICS
This screen displays the transmit and receive statistical information of
the AP. Click “Reset Counters” to clear the data.
ABOUT
This screen displays basic information about the utility, including the
MAC address.
MAC Table
32
SoftAP
SPECIFICATIONS
Standards
• IEEE 802.11b (11 Mbps Wireless LAN)
• IEEE 802.11g (54 Mbps Wireless LAN)
• Upward compatible to IEEE 802.11n draf t 2.0 (150 Mbps Wireless LAN)
General
• Interface: Hi-Speed USB 2.0
• Chipset: Ralink RT3070
• Frequency band: 2.400 0 – 2.4835 GHz (Industr ial Scientic Medical Band)
• Modulation technologies:
- 802.11b: Direct Sequence Spread Spectrum (DSSS): DBPSK, DQPSK, CCK
- 802.11g: Orthogonal Frequency Division Multiplexing (OFDM): BPSK, QPSK,
16QAM, 64QAM
- 802.11n: Orthogonal Frequency Division Multiplexing (OFDM): BPSK , QPSK,
16QAM, 64QAM
• Security:
- 6 4/128-bit W EP data encr yption
- WPA and WPA2
- Cisco CCX
• Transmit power:
- 11n: 14 dBm +/- 1.5 dBm
- 11g: 14 dBm +/- 1.5 dBm
- 11b: 17 dBm +/- 1.5 dBm
• Receive sensitivit y:
- 150 Mbps OFDM: -70 dBm +/- 1.5 dBm
- 5 4 Mbps OFDM: -78 dBm +/- 1.5 dBm
- 11 Mbps CCK: -92 dBm +/- 1.5 dBm
• Certication: FCC Class B, CE
LEDs
• Link/Activity
Environmental
• Dimensions: 10 (H) x 28 (W) x 89.6 (L) mm (0.4 x 1.1 x 3.5 in.)
• Weight: 0.17 kg (0.4 lbs.)
• Operating temperature: 0 – 40°C (32 – 104°F)
• Operating humidity: max. 95% RH, non-condensing
System Requirements
• Notebook or Desktop PC with Pentium 1 GHz-compatible processor or higher
• Windows 2000/XP/Vista/7
• Available Hi-Speed USB 2.0 type-A por t
Package Contents
• Wireless 150N USB Adapter
• USB extension cable
• Setup CD with user manual; quick installation guide
SPECIFICATIONS
33
INTELLINET NETWORK SOLUTIONS™ offers a complete line
of active and passive networking products.
Ask your local computer dealer for more information or visit
www.intelline t-network.com.
INTELLI NET is a tradema rk of IC INTRACOM , registered in t he U.S. and other co untries.
© IC INTR ACOM. All rights res erved.
Loading...