Intelligent Weighing Technology PG Series, Intell-Lab PG Series User Manual

1. Environmental Conditions

a. Place the balance on a stable platform, away from vibration, air

currents, direct sunlight and strong electromagnetic waves.

b. Ensure the balance is level by using the adjustable feet.

Operating temperature: 41 °F to 95 °F / 5 °C to 35 °C
Temperature fluctuation ≤5 °C / hour.

Humidity 50% to 85% RH.

2. Operation

a. Please use the AC/DC adapter provided. Failure to do so will

void the warranty. Plug in the power cord and wait 5 minutes
before turning on the balance.

b. Turn on the balance using the ON/OFF key. Following the

8.8.8.8.8. display, the balance will display maximum capacity,
“S--CAL”, then 0.00 g in weighing mode. Please allow at least
15 minutes for the balance to warm up before using. (Longer if
the temperature is below 60 °F).

3. Calibration

a. Single range calibration (recommended). Press “CAL” for 3

seconds. The display will show “CA-dA”, then display the
weight to be applied (in grams). Apply the weight, the display
will show CAL, followed by the weight value. The balance may
now be used. If the weight reading is not correct (due to
environmental conditions), repeat the process.

4. Weighing

a. When the black dot at the bottom left of the display has

disappeared, the balance is stable and ready to begin
weighing. Please press the “TARE” key before weighing.

b. If the display shows “--------“, the balance has been overloaded.

Remove the weight and begin again with a smaller load.

5. Tare

a. When the balance is stable, press the “TARE” key to always

start weighing at zero.

6. Backlight

a. Press the “BL” backlight button to turn the backlight on and off.

7. Zero-Tracking and Auto-Tare

a. Turn the balance off. Press and hold the “CAL” key and at the

same time, turn the balance on. The display will show “-Zero-”.
Press the “TARE” key. The display will show “Zero*d”. Press
the “TARE” key to change the value from 0 to 5, “Zero0d”
meaning no zero-tracking and the sensitivity is the highest.
“Zero5d” is the factory setting. Press backlight to return to
weighing.

b. Press the “CAL” key. The display will show “-tArE-“. Press the

“TARE” key to adjust the “*” from 0 to 9. “tArE0d” means there
is no auto-tare. “tArE9d” is the factory setting.

c. “Press the “BL” backlight key to confirm settings. The display

will then show “0.0”. Your settings will remain the same when
the balance is turned on again.

8. Other Functions

a. Units. Press “MODE” for 3 seconds. “Unit” will flash. Then

press the “TARE” key and the current unit will flash. Press the
“MODE” key to toggle between units. Press the “TARE” key to
confirm. The balance will return to weighing in the unit chosen.

b. Counting. Press the “MODE” key for 3 seconds until the

display flashes. Press the “MODE” key again to choose
“Count”. Then press the “TARE” key to confirm. The display
will show “pcs”. Press the “MODE” key again to choose from
“10pcs” to “500pcs”. The larger the number, the higher the
count accuracy. Put the sample parts on the balance pan and
press the “TARE” key to confirm the sample size. The display
will show “----“. If the sample size is too small the display will
show “no-Cou”.

c. Percentage. Press the “MODE” key for 3 seconds until the

display flashes. Press the “MODE” key again to choose “PER”.
Then press the “TARE” key to confirm. The display will show
“100%”. Place the sample to be weighed on the pan and press
the “TARE” key to confirm the sample as 100%. Remove the
sample and place the goods on the pan. The display will show
“###%”. If the amount on the pan is too small a weight the
display will show “no-PER”.

d. Print. Press the “MODE” key until “Prt” is displayed. Press the

“TARE” key to confirm. Press the “MODE” key to change
between “hAnd”, “Auto” and “Contin”. Press the “TARE” key to
accept.

i. “hAnd” – Print on demand

ii. “AUto” – Print when the balance is stable

iii. “Contin” – Print continuously

RS 232 port parameter
ASCII code transmission data format: Every 10BIT as a
Data frame.
1 start bit, 8 data bits, 1 stop bit, no parity
Baud rate: 9600 bps

Protect the unit against moisture.
Please disconnect the unit from the main power supply before cleaning. Do not

use any liquids or aerosol sprays to clean this unit. Use only a clean dampened
cloth.

Intelligent Weighing Technology, Inc.

www.intelligentwt.com

A Higher Level of Precision…

A Higher Level of Performance

Intell-Lab™ Toploading Balance
PG Series

User Manual

© 2010 Intelligent Weighing Technology, Inc. All rights reserved worldwide.
The information contained herein is the property of Intelligent Weighing Technology, Inc. and is supplied without liability for errors or

omissions. No part may be reproduced or used except as authorized by contract or other written permission. The copyright and the
foregoing restriction on reproduction and use extend to all media in which the information may be embodies.