1
MAINTENANCE MANUAL
AXM SERIES
CONTENTS
1. INTRODUCTION
2. SPECIFICATIONS
2.1 SYSTEM BLOCK DIAGRAM
2.2 PHYSICAL LAYOUT OF ELECTRICAL CONNECTION
2.3 GENERAL SPECIFICATIONS
3. INITIAL SETUP
3.1 INTERNAL FUNCTIONS AND SETTING METHODS
3.2 CALIBRATION
3.3 DISABLE CALIBRATION AND INTERNAL FUNCTIONS SETTING WITH JUMPER
SW.(JP1)
3.4 OFFSET AND SPAN VALUE DATA
4. TROUBLE SHOOTING
4.1 TROUBLE SHOOTING LOOP
4.2 PARTS AND COMPONENTS TROUBLE SHOOTING
5. ELECTRICAL CIRCUITRY
5.1 SCHEMATICS
5.2 PCB LAYOUT
6. BILL OF MATERIAL
7. APPENDIX
OCT 2009 REV 2
2
Specifications and Function Subject to Change without Notice
1. INTRODUCTION
The AXM series is designed and programmed according to the OIML R-76
Class III requirements.
This scale is sealed to prevent unauthorized access to internal parts.
Ender users should be advised not to underta ke any trouble shooting
except those listed on the operation manual.
This maintenance manual contains of certain information that may result
in fraudulent use. Do not release any part of this manual to any end
users or un-authorized persons.
The internal mini jumper should be so s et to prevent un-author ized
settings or alternations.
Should a load cell has been replac ed, make sure that the protection
devices are properly set.
After servicing, it is necessary to go through all tests and procedures
to ensure the scale meets all the meteorological and approval
requirements.
Here are some features of the AXM series
1. Designed to meet OIML-R76 class III requirements.
2. Zero Indicator.
3. Net Indicator.
4. Negative Value Indicator.
5. Auto Tare Function.
6. Power on Zero Function.
7. Manual Zero Function.
8. Extended Display Function.
9. Auto Power Saving Function.
10. Metric/Avoirdupois Conversion Function.
11. Low battery warning signal.
12. 2 points Calibration.
13. Mini jumper to prevent end-user calibration.
14. Optional EL backlights.
15. Optional RS232C interface.
16. Optional Rear Display
17. Built-in rechargeable battery operated.
18. Battery operating time: 200 hours plus after charged.
3
2. SPECIFICATION
2.1 SYSTEM BLOCK DIAGRAM
Description:
When a mass is placed on the platform, the load of the article is applied
to the load cell inside it.
The resistance to the excitation current in the strain gauge will then
changed and the analog output signal varies.
It is amplified and digitized continuously by the A/D converter into
a digital signal. Subsequently, the resulting count is processed and
managed by the CPU. The CPU refers to the instructions from the keyboard,
and then conveys the output data to LCD driver, which formats the data
into readout on the display panels.
LCD DRIVER
CPU
with ROM
E+
LOAD E-
CELL S+
S-
POWER SUPPLY:
AC ADAPTOR
(9V/500mA)
RECHARGEABLE
BATTERY (6V 4Ah)
A/D UNIT
KEYBOARD
(4 KEYS)
L
CD
INTERFACE
4
2.2 PHYSICAL LAYOUT OF ELECTRICAL CONNECTION
AXM-
40-
X
O
PTIONAL REAR PISPLAY BOARD
LOAD CELL
RECHARGEABLE
BATTERY
6V 4Ah
DC JACK
MAIN BOARD
AXM-10-X
J
2
J
5
E+
E-
S+
S
-
J4
LCD
LCD
J
3
RS-
2
32 BOARD
R
S232C
-
1
B1
POWER BOARD
GM-20-X
J1
M
EMBRANE K/B
5
2.3 GENERAL SPECIFICATION
2.3.1 Overall View
6
2.3.2 Dimension:
Platter size：250 x 215mm
Overall size：250(W) x 285(D) x 105(H)mm
2.3.3 Model Specifications
Model Number Capacity (Max) Division (e)
AXM-1500 1500g 0.5g
AXM-3000 3000g 1g
AXM-6000 6000g 2g
AXM-15K 15kg 0.005kg
AXM-30K 30kg 0.01kg
SOFTWARE NUMBER CE019
Approval Class III
Maximum Tare Range 1/3 Max -1e
Power on Zero Range
±10% Max
Manual Zero Range
±2% Max
Min. Load 20e
Operation
Environment
0o~40oC (32o~104oF),
Non-condensed. R.H.≦85%
Power Consumption 0.5W (when charged)
2.3.4 Main Components Used
Microprocessors: SM8958
Crystal Oscillator: 11.0592MHz
Display Device: WTN Liquid Crystal Display
2.3.5 Analog Specification
-
The maximum number of verification scale intervals will be:
n ≤ 3000 for class
III
instruments
- Power supply of 5 V DC;
-
16 bits serial digital output;
-
Excitation power supply for the load cell is 5 V DC;
-
Input impedance of the load cell is 350 Ω;
-
The analog data processing unit is built in a cl osed me tal box .
7
3. INITIAL SETUP
3.1 INTERNAL FUNCTIONS AND SETTING METHODS
INTERNAL FUNCTION TABLE
Function Symbol Description
1 F1 Span value reading
2 F2 Full display segment check
3 F3 Scale configuration
4 F4 Auto power off setting
9 F9 Auto tare setting
19 F19 1/30000 Verification Mode**
20 F20 Gravity Compensation-place of calibration**
21 F21 Gravity Compensation-place to be used**
HOW TO ENTER THE REQUIRED FUNCTION MODE
a. Turn scale off.
b. Press and hold TARE, then turn scale on. Sca le disp lay F.1
c. Press TARE until the required function number appears.
d. Press MODE
e. Press MODE until the required sett ing appear s.
f. Press TARE to confirm.
g. Repeat step c to f for other function setting, or
h. Press ON/ZERO to save settings and return to normal operation.
F1 Span Value Reading
a. Simply enter F1 to read the A/D counts.
b. Press ON/ZERO to clear the A/D counts, apply test mass onto platter,
the span value of test mass will be displayed.
F2 Full Display Segment Check
When function is entered, scale will firstly display the software
version, and then displays all segments later.
Check and make sure that no segments are missed.
F3 Scale Configuration
a. Enter F3, scale displays the offset value.
b. Press and hold MODE, available scale capacity and min.
division appears.
SELECT DISPLAY RESOLUTION
c. Press and hold MODE to change the display resolution.
SELECT WEIGHT UNITS
d. when desired display resolution is selected, press MODE
8
to select weight units.
--To employ all (metric and pound/oz) weight units, press
MODE until ‘g’(kg), ‘lb’ indicators appear.
--To disable ‘lb’ weight unit, press MODE until ‘g’(kg)
indicator appears only.
SELECT SCALE CAPACITY
e. Press MODE to select the capacity, Press TARE to save
setting.
f. Re-calibration will be required after scale capacity
changed.
F4 Auto Power Off Setting
Two modes are available: (Default=4_OFF)
Press MODE until desired setting appear, press TARE to save
setting.
0_OFF = Auto Power Off function is disabled.
4_OFF = Scale will automatically turns it off after 4 minutes
unused.
F9 Auto Tare Setting
Two modes are available: (Default=TroFF)
TroFF = Auto tare function is disabled.
Tr_on = Scale will automatically tare off the initial weight that
places on the platter.
**
F19~F21 Reserved
9
3.2 CALIBRATION
Dealer Calibration Procedures:
1. Turn scale off.
2. Press and hold TARE, then turn scale on.
3. Scale displays F1
4. Press MODE
5. Scale displays offset value
6. Press and hold MODE, Scale displays YES.
7. Scale will self calibrate zero point before proceed to the first
point calibration.
8. After zero point calibration is done, scale displays LOAD XXXX or
XXXX
9. Load calibration load as request.
10. Wait until scale displays LOAD XXXX(second point).
11. Load calibration load as request o r press MODE to abandon second
point calibration, wait until scale displays DONE.
12. Calibration completed and scale is ready for operation.
Auto Calibration Procedures:
1. Turn scale off.
2. Press and hold MODE, then turn scale on.
3. Scale displays CAL.?
4. Press MODE again, Scale displays YES.
5. Scale will self calibrate zero point before proceed to the first
point calibration.
6. After zero point calibration is done, scale displays LOAD XXXX or
XXXX
7. Load calibration load as request.
8. Wait until scale displays LOAD XXXX(second point).
9. Load calibration load as request or press MODE to abandon second
point calibration, wait until scale displays DONE.
10. Calibration completed and scale is ready for operation.
Note
：
Auto calibration can only be performed when the span
value Is within +/-10% tolerance of dealer calibration.
3.3 DISABLE CALIBRATION AND INTERNAL FUNCT IONS SETTING WITH JUMPER
SW.(JP1)
The JP1 is used to control calibration and internal functions
setting(F1 and F3). move this jumper to CAL-LOCK position to disable
calibration and internal functions setting.
1
0
CAUTION:
IF THE SCALE WILL BE SOLD TO AN APPLICATION THAT IS LEGAL
FOR TRADE. IT IS HIGHLY RECOMMEND SETTING THE JUMPER TO
CAL-LOCK POSITION TO DISABLE THE CALIBRATION AND INTERNAL
FUNCTION SETTING.
3.4 OFFSET AND SPAN VALUE DATA
OFFSET AND SPAN VALUE DATA TABLE
Offset Value
(Thousand)
Span Value(Thousand)
Offset
Control
Span Control(Ohm)
R9
10~14 30~60 at 33% of Max. R1, R2 150
READING OFFSET VALUE
1 Turn scale off
2 Remove all load from platter
3 Enter F3 and read the offset value
READING SPAN VALUE
1 Turn scale off
2 Remove all load from platter
3 Enter F1
4 Press ZERO
5 Apply load to platter. Span value according to load applied
will be displayed.
HOW TO ADJUST OFFSET VALUE
In case the offset value is out of range, change the resistors R1,R2
to obtain correct offset value.
HOW TO ADJUST SPAN VALUE
The span value is controlled by the resistor locating at R9, standard
resistor value of R9 is listed on the abov e table. If the required
span value is not attained, then change R9 resistor according to either
case below:
Span value too low: Decrease the resistance of R9.
Span value too high: Increase the resistance of R9.
1
1
CHECK LOAD CELL,
A/D UNIT,OFFSET
VALUE
CHECK POWER
SUPPLY,LCD,LCD
DRIVER IC,R21,23
CHECK PLATFORM
STOPPER,LOAD
CELL,A/D UNIT,
BAD SOLDERING
RE-CALIBRATE
THE SCALE
C
HECK PLATFORM
STOPPER,LOAD
CELL,OFFSET
VALUE
4. TROUBLE SHOOTING
4.1 TROUBLE SHOOTING LOOP
POWER ON
COUNT DOWN
?
NO DISPLAY
D
ISPLAY RANDOM
F
IGURE
CHECK POWER SUPPLY,
CPU,LCD,KEYBOARD
CHECK CPU,LCD,
LCD DRIVER IC
O
K
COUNTS AND
THEN ZERO?
O
K
PROPER READOUT
?
CORRECT READOUT
?
NORMAL OPERATION
S
HOW
“
0
0000”
U
NSTABLEGHOST
O
K
OK
INCORRECT
CAN’T REACH THE
F
ULL CAPACITY
1
2
4.2 PARTS AND COMPONENTS TROUBLE SHOOTING
4.2.1 Power Supply Checking
4.2.1.1 Relevant parts:
Power Board (GM-20-X)
Q1 (C1061)
Q2 (C945)
R1 (1.2R 1/2W)
ZD1(ZENER 8.2V)
DC JACK
BATTERY(6V 4Ah)
1
2
3
4
MB
SIP4
Q3
A733
D1
1N4148
L1
L-59EGW
ZD1
8.2V
B1
W04 1A
J1
SCD-22
R2
1/2W 100R
Q2
C945
R1
1/2W 1.2R
Q1
C1061
R3
15K
1
2
BAT
2PIN
R4
470R
R5
1/4W 220R
Main Board (AXM-10-X)
Q1 (A1515)
Q2 (C945)
Q6 (A733)
U6(AIC 1722-5.0)
1
3
Description:
1) Power source: Rechargeable Battery 6V/4Ah or AC adaptor(9V,
500mA)
2) How Battery is charged completely?
The charging voltage is regulated by Q1 (C1061) and ZD1 (8.2V) for
about 7 volts.
The charging current will go down automatically when voltage reached.
Q2 (C945) and R1 (1.2R, 1/2W) provide Over-Current protection.
3) +5V power drives digital circuit system.
U6 (AIC 1722-5.0) is a 5volts Voltage Regulator.
4) +5V power drives analog circuit system.
U4 (NS2950A) is a 5volts Voltage Regulator.
4) Auto-off:
If the scale is set with 4_oFF or even under LO-BAT situation,
after fixed time interval, CPU will release a low potential signal
to draw down Q2, then Q1 cuts off, the scale will be shut down
immediately.
5) Low Power Detection:
The Q6(A733) is designed to detect the powe r level. When battery
power is less than 5.5V, the collector pole will become high potential,
then CPU will instruct LCD display to show LO-BAT symbol.
4.2.1.2 Input voltage: 5.5V or higher
Check and recharge battery if voltage is less than 5.5V.
4.2.1.3 System voltage (Vcc): 5V +/- 10%
Check that the system voltage is within 5V +/- 10%
a) less than 4.5V, the CPU may not work properly.
b) more than 6V, ghost will appear on LCD.
4.2.2 Platform Stopper Checking
The platform device shall not touch anything around itself during
operation. Check that the platform is not contacted with the upper
(no load) and/or lower (with load) stopper.
4.2.3 LCD Display Checking
4.2.3.1
Check that it is soldered and connected properly between LCD
and driver IC (PCF8576), driver IC (PCF8576) and CPU.
1
4
4.2.3.2
Check whether LCD is broken.
4.2.4 CPU Checking
4.2.4.1
Check that all pins are seated properly into the socket.
4.2.4.2
Check that the Crystal Oscillator works.
4.2.4.3 Check the RESET is normally low.
4.2.5 A/D Unit Checking
4.2.5.1
Check that the +5V powers are correctly fed to the
A/D unit.
4.2.5.2 Check that the signal output of loadcell is normal.
4.2.5.3
Check OP. Amplifiers & A/D Converter (AD7705).
When no error is found with the above checking procedures, the trouble
can be caused on the load cell or the PCB itself. Replace a new one
could be better to identify the defective.
In this way, the readout of weight would be varied because of the output
voltage of load cell and different span valu e, so re-calibration is
required after this replacement.
1
5
5. ELECTRICAL CIRCUITRY
5.1 SCHEMATICS
1
6
1
7
1
8
1
9
2
0
1 2 34
A
B
C
D
4
321
D
C
B
A
Title
Number RevisionSize
A4
Date: 1-Dec-2000 Sheet of
File: E:\GM20B.S01.sch Drawn By:
BATTERY6V 10AH
123
4
MB
SIP4
Q3
A733
D1
1N4148
L1
L-59EGW
ZD1
8.2V
B1
W04 1A
J1
SCD-22
R2
1/2W 100R
Q2
C945
R1
1/2W 1.2R
Q1
C1061
R3
15K
1
2
BAT
2PIN
R4
470R
R5
1/4W 220R
G
S
E
R
I
E
S
C
H
A
R
G
I
N
G
G
M
2
0
2
1
1
B
E
N
L
E
E
B
O
A
R
D
2
1
5.2 PCB LAYOUT
AXM-10-1 TOP LAYER
AXM-10-1 BOTTOM LAYER
AXM-10-1 TOP OVERLAY
AXM-10-1 BOTTOM OVERLAY
2
2
AXM-40-1 TOP LAYER
AXM-40-1 BOTTOM LAYER
AXM-40-1 TOP OVERLAY
AXM-40-1 BOTTOM OVERLAY
2
3
6. BILL OF MATERIAL
STRUCTURE
Parts No. Description Specification Qty Remark__
E1AXM000010 P.C.B. KIT AXM-10-1 MAIN BOARD 1
E1AXM001000 P.C.B. KIT AXM-40-1 REAR BOARD 1
E1GSP010000 P.C.B. KIT GM-20-1 POWER BOARD 1
A0002030*** LOAD CELL C2G1 1
AXM-1500 C2G1-3kg
AXM-3000 C2G1-6kg
AXM-6000 C2G1-10kg
AXM-15K C2G1-20kg
AXM-30K C2G1-35kg
A6010230950 ADAPTOR 230V/ 9V 500mA 1
C1GW0000000 PANEL PC GW SERIES, 135.5*45.5*0.8mm 1
C1AXM030000 OVERLAY AXM SERIES 1
C1AXM030999 REAR PANEL AXM SERIES, REAR DISPLAY 1
A1205010210 BATTERY WIRE 21cm (BLACK) 1
A1205010212 BATTERY WIRE 21cm (RED) 1
A1600060400 RECHARGEABLE BATTERY GP4-6 6V 4AH 1
A5001000301 CABLE TIE CV-120S 3
A5005000090 BUBBLE LEVEL D14 (Dia. 14mm) 1
F0009000032 S/S PLATE(NO.32) XM SERIES, 220*185*0.5mm 1
F0003GSP100 ALUMINUM L/C SUPPORT GSP SERIES (C2X1 L/C) 1 UPPER
F0003GSP101 ALUMINUM L/C SUPPORT GSP SERIES (C2X1 L/C) 1 UNDER
G0001GSP000 PLASTIC CABINET, UNDER GSP SERIES (GRAY) 1
G0001GM0000 PLASTIC CABINET, UPPER GM SERIES(WHITE) 1
G0002GSP000 PLASTIC PLATTER GSP SERIES 1
G0004GSP000 RUBBER PAD CFR-190603 (GSP SERIES) 4
G0004MP0001 ADJUSTABLE FEET M SERIES 4
G0009EM0002 BATTERY CAP EM SERIES(GRAY) 1
Y0007GEC000 PACKING MATERIAL GEC SERIES 1
Z7GEC000000 DUST COVER G SERIES 1
A1007000002 FERRITE CORE TR-14.1*6.28*28.6mm 1
A1007000001 FERRITE CORE TR-16*9*28mm 1 LOADCELL
A1007000011 FERRITE CORE 19*6.5*32(CLAMP TYPE) 2 POWER,RS-232 TO MAIN BOARD
AXM-10-X MAINBOARD
2
4
E0AXM000010 P.C.B. AXM-10-1 1
A0102000289 L.C.D. UTN-G289JV-W 1 LCD1
A0201089582 I.C. SM8958C25P 1 U5
A0202093461 I.C. 93C46 1 U7
A0207017225 VOLTAGE REGULATOR I.C. AIC1722-50CZT 1 U6
A0208085760 I.C. PCF8576CT 1 U8
A0300000040 I.C. SOCKET 40 PIN 1 U5
A0401007330 TRANSISTOR A733 1 Q6
A0401009450 TRANSISTOR 2SC945 2 Q2,7
A0401015150 TRANSISTOR 2SA1515R(2SB1116K,A950Y) 2 Q1,8
A0501004148 DIODE 1N4148 1 D2
A0701106017 CAPACITOR (EC) 10uF/25V(SS TYPE) 2 C23,37
A0701107016 CAPACITOR (EC) 100uF/16V 2 C39,51
A0701226017 CAPACITOR (EC)
22μF/16V (SS TYPE)
2 C24,38
A0701477016 CAPACITOR (EC) 470uF/16V 1 C18
A0730104050 CAPACITOR (MLC) 104Z 9 C25,27,28,32~34,49~50,52
A0740030050 CERAMIC CAPACITOR (CC) 30pf/50V(30) 2 C42,43
A0740101050 CERAMIC CAPACITOR (CC) 100pf/50V(101) 7 C19~22,29,30,48
A0740102050 CERAMIC CAPACITOR (CC) 1000PF/50V(102) 1 C26
A0804041503 METAL FILM RESISTOR
150KΩ 1/4W
1 R48
A0804045003 METAL FILM RESISTOR
500KΩ 1/4W
1 R49
A0805041101 CARBON FILM RESISTOR
100Ω 1/4W
2 R17,18
A0805041102 CARBON FILM RESISTOR
1KΩ 1/4W
2 R26,28
A0805041103 CARBON FILM RESISTOR
10KΩ 1/4W
9 R19,20,22~24,27,29,30,43
A0805041153 CARBON FILM RESISTOR
15KΩ 1/4W
1 R21
A0805041223 CARBON FILM RESISTOR
22KΩ 1/4W
2 R47,50
A0805041272 CARBON FILM RESISTOR
2.7KΩ 1/4W
2 R44,51
A0805041472 CARBON FILM RESISTOR
4.7KΩ 1/4W
2 R25,45
A0805041473 CARBON FILM RESISTOR
47KΩ 1/4W
1 R46
A0802010305 RESISTOR NETWORK
10KΩ 5 PIN
2 NR8,9
A0901011040 CONNECTOR 4 PIN WAFER 90° 1 J2
A0907020300 CONNECTOR (PIN PLUG) 2 x 15 PIN 180° 1 J4
A0910000070 CONNECTOR (FPC) 7 PIN 180° 1 J5
A0910100130 SOCKET STRIPS SIP 1*13(FEMALE) 1 LCD1
A0910100140 SOCKET STRIPS SIP 1*14(FEMALE) 1 LCD1
A0907010030 CONNECTOR 1 * 3 PIN 180° 1 JP2
A0910111020 MINI JUMPER PITCH 2.54 1 JP2
2
5
A1100211059 CRYSTAL 11.0592MHZ 1 X1
A1500000004 BUZZER OBO-15210 1 BZ1
A/D SECTION
A0203077050 I.C. AD7705AN 1 U3
A0206000072 I.C OP177 2 U1-2
A0207029500 VOLTAGE REGULATOR I.C. AS2950AW 1 U4
A0702226016 CAPACITOR (TC) 22uF/16V(226) 1 C10
A0713105063 POLYESTER FILM CAPACITOR(MEF) 1uF/63V (105) 1 C7
A0730104050 CAPACITOR (MLC) 104Z 10 C1-6,C8-9,C16-17
A0740047050 CERAMIC CAPACITOR (CC) 47pf/50V(47) 2 C11-12
A0740101050 CERAMIC CAPACITOR (CC) 100pf/50V(101) 3 C13-15
A0803041002 METAL FILM RESISTOR
10KΩ 1/4W
2 R7-8
A0803041501 METAL FILM RESISTOR
1.5KΩ 1/4W
1 R12
A0803043001 METAL FILM RESISTOR
3KΩ 1/4W
1 R11
A0803041500 METAL FILM RESISTOR
150Ω 1/4W
1 R9 (SPAN)
A0804044701 METAL FILM RESISTOR
4.7KΩ 1/4W
4 R3-6
A0805041101 CARBON FILM RESISTOR
100Ω 1/4W
3 R10,R13-14
A0805041103 CARBON FILM RESISTOR
10KΩ 1/4W
1 R16
A0805041561 CARBON FILM RESISTOR
560Ω 1/4W
1 R15
A1008000001 EMI FILTER DSS-306-55Y5S471M100 3 EMI1-3
A1100249152 CRYSTAL 4.9152MHZ 1 X2
F0015000012 PROTECTION BOX 7705-52-1 (UPPER) 1
F0015000013 PROTECTION BOX 7705-52-1 (UNDER) 1
Z0010000305 SCREW M3*6 2
AXM-40-1 REAR BOARD
2
6
E0AXM001000 P.C.B. AXM-40-1 1
A0102000289 L.C.D. UTN-G289JV-W 1 LCD1
A0910100130 SOCKET STRIPS SIP 1*13(FEMALE) 1 LCD1
A0910100140 SOCKET STRIPS SIP 1*14(FEMALE) 1 LCD1
A0907020300 CONNECTOR (PIN PLUG) 2 x 15 PIN 180° 1 J1
A0701107016 CAPACITOR (EC) 100uF/16V 1 C1
A0730104050 CAPACITOR (MLC) 104Z 1 C2
A0805041102 CARBON FILM RESISTOR
1KΩ 1/4W
1 R1
A1203300400 FLAT CABLE 30PIN 40CM 1 J1
BACK LIGHT OPTION
A1400000006 BACK LIGHT 130.0*44mm 1 EL1
A1401005000 BACK LIGHT INVERTER
5V / 90c ㎡
1 IN1
RS232 OPTION
E1GEC100000 P.C.B. KIT RS232C-1B1 RS232 BOARD 1
A0901010040 CONNECTOR 4 PIN WAFER 1 J3
A1007000002 FERRITE CORE TR-14.1*6.28*28.6mm 1
A1202040401 WIRE ARRAY 4PIN 40cm, SINGLE HOUSING 1
2
7
7. APPENDIX
2
8
ITEM PART NAME DESCRIPTION QTY
1 PLASTIC CABINET, UPPER GM SERIES(WHITE) 1
2 PLASTIC CABINET, UNDER GSP SERIES (GRAY) 1
3 ALUMINUM L/C SUPPORT(UPPER) GSP SERIES (C2X1 L/C) 1
4 ALUMINUM L/C SUPPORT(UNDER) GSP SERIES (C2X1 L/C) 1
5 PLASTIC PLATTER GSP SERIES 1
6 ADJUSTABLE FEET M SERIES 4
7 BATTERY CAP EM SERIES(GRAY) 1
8 OVERLAY AXM SERIES 1
9 REAR PANEL AXM SERIES, REAR DISPLAY 1
10 LOAD CELL C2G1 1
LOAD CELL C2G1
AXM-1500 C2G1-3kg
AXM-3000 C2G1-6kg
AXM-6000 C2G1-10kg
AXM-15K C2G1-20kg
AXM-30K C2G1-35kg
11 RUBBER PAD CFR-190603 (GSP SERIES) 4
12 PANEL PC GW SERIES, 135.5*45.5*0.8mm 1
13 RECHARGEABLE BATTERY GP4-6 6V 4AH 1
14 S/S PLATE (NO.32) XM SERIES, 220*185*0.5mm 1
15 P.C.B. KIT AXM-10-1 MAIN BOARD 1
16 P.C.B. KIT AXM-40-1 REAR BOARD 1
17 P.C.B. KIT GM-20-1 POWER BOARD 1
18 FLAT CABLE 30PIN 40CM 1
19 WIRE ARRAY 4PIN 40cm, SINGLE HOUSING 1
20 BUBBLE LEVEL D14 (Dia. 14mm) 1
21 MEMBRANE K/B XM SERIES(OIML) 1
2
9
APPROVED NO.
DRAWING NO.: AXM0-M-01-A
REV.
1
DWG.
NAME
AXM SERIES
SEALING DIAGRAM
AXM SERIES SEALING DIAGRAM
SEALING POSITION
Loading...