V110
Installation and Operation
User Guide
Marine Satellite Communication Antenna System
Serial number of the product
This serial number will be required for the all
troubleshooting or service inquiries.
© 2009 Intellian Technologies Inc. All rights reserved.
Intellian and the Intellian logo are trademarks of Intellian
Technologies, Inc., registered in the U.S. and other countries.
v-Series and v110 are trademarks of Intellian Technologies, Inc.
Intellian may have patents, patent applications, trademarks,
copyrights, or other intellectual property rights covering subject
matter in this document. Except as expressly provided in any
written license agreement from Intellian, the furnishing of this
document does not give you any license to these patents,
trademarks, copyrights, or other intellectual property.
All other logos, trademarks, and registered trademarks are
the property of their respective owners. Information in this
document is subject to change without notice.
Every effort has been made to ensure that the information
in this manual is accurate. Intellian is not responsible
for printing or clerical errors.
Intellian Technologies Inc.
2F. Dongik Bldg, 98 Nonhyun-dong,
Gangnam-gu, Seoul 135-010, Korea
Tel: +82 2 511 2244
Fax: +82 2 511 2235
Email: info@intelliantech.com
November 16, 2009
Intellian Technologies USA, Inc.
9261, Irvine Blvd.
Irvine, CA 92618
Tel: +1 949 916 4411
Fax: +1 949 271 4183
Email: infoUS@intelliantech.com
Doc. No. PM-v110-v1.0
Contents
INTRODUCTION ............................................................................................. 1
Introduction to Intellian v110 ............................................................................ 1
Features of Intellian v110 .................................................................................... 2
Basic System Configuration ............................................................................... 3
I
NSTALLING THE ANTENNA ............................................................................ 4
System Components ............................................................................................. 4
Tools Required for Installation .......................................................................... 9
Planning the Installation .................................................................................... 10
Configure Radiation Hazard/Blockage Zones ........................................... 11
Preparing the Installation .................................................................................. 13
I
NSTALLING THE ACU .................................................................................. 24
ACU Dimensions ................................................................................................... 24
Selection of ACU Installation Site .................................................................. 24
Installing the ACU ................................................................................................ 25
Connecting the System to a Ship’s Gyro ..................................................... 26
ACU Connector Guide ........................................................................................ 27
O
PERATING THE ACU .................................................................................. 28
Introduction ............................................................................................................ 28
ACU Soft Keys ........................................................................................................ 30
Normal Mode ........................................................................................................ 31
Setup Mode ............................................................................................................ 34
Installation Settings ............................................................................................. 35
Antenna Settings .................................................................................................. 38
Satellite Settings ................................................................................................... 50
System Settings ..................................................................................................... 57
PC
CONTROLLER PROGRAM ......................................................................... 64
Introduction ............................................................................................................ 64
Program Initialing and Communication Setup ......................................... 65
Main Menu .............................................................................................................. 66
Controller Menu .................................................................................................... 68
W
ARRANTY ................................................................................................ 76
Appendix : v110 Technical Specification ..................................................... 77
Introduction
Introduction to Intellian v110
The Intellian v110 is a 1.05 meter Ku-band marine VSAT communication
antenna system for SCPC, broadband, or hybrid networks and is suitable
for high-speed Internet, email, file transfer, video conference, VOIP, VPNs
and database backup. The v110 is a 3-axis stabilization system designed
for the oceangoing vessels that require “always on” and “high quality”
broadband communications no matter how rough the weather and sea
conditions are.
The v110 has an unlimited azimuth range for continuous tracking
without the needs to unwrap the cables in the antenna. The wide
elevation range from -15 to 120 degrees enables the v110 to have
seamless signal reception while the vessel is traveling near the equator
or Polar Regions.
The v110 meets the FCC’s 2-degree spacing requirement and is built
with Intellian’s extremely high vibration and shock standards. The simple
design of the v110 offers lighter weight and greater reliability than any
competitor’s system in its class. With easiest installation design and
most-user friendly interface you can find in the market, the v110
guarantees that you will have a whole new broadband experience at sea.
Introduction
1 Introduction
Features of Intellian v110
Enjoy always-on broadband connection at sea
Intellian v110 is the most modern communication system that enables
you to receive a high-speed and always-on broadband connection at sea,
where the atmospheric and environmental conditions are very harsh.
Best solution for all kinds of vessels
The v110 is the best solution for all kinds of vessels that require the
satellite broadband connection around the globe. The v110 is a highgain, high-efficient system that offers an extraordinary signal gain than
any other systems in its class.
3-axis stabilized system with a wide elevation angle
The v110 has a wide elevation range from -15 to 120 degrees which
offers seamless signal reception while the vessel is traveling near the
equator or Polar Regions.
Outstanding reliability
Intellian v110 provides highly reliable system through the
implementation of a modularized design, the usage of strictly proven
components and Intellian’s rigorous environmental test standards.
Built-in GPS
Intellian v110 has an imbedded GPS, which allows for the system to
upload the GPS data automatically into the system for an even faster
and stable system.
Built-in automatic skew angle control system
The automatic skew control system allows Intellian v110 to maintain the
optimal skew angle at all times and ensure maximum level of satellite
signal level.
2
V110 – Marine Satellite Communication System
Basic System Configuration
For your satellite communication system to work properly, the system
will have to be connected with all of the provided components properly,
as shown in the figure below (see the “Installation” section of this
manual). Separate purchase of a satellite modem is required.
Ship’s
Gyrocompass
(Not supplied)
NMEA/Synch ro /SMS
Tx
8W BUC
Power (+48V)
AC
110/220V
Rx/Power/Data
Antenna Control Unit
TCP/IP
Rx
Figure 1. Basic System Configuration
Satellite Modem
(Not supplied)
Introduction
3 Introduction
Installing the Antenna
The components of the Intellian v110 have been designed to be
modular so that it is suitable for simple installation on all types of
vessels.
System Components
The Intellian v110 consists of two major units, antenna assembly unit
and antenna control unit.
Antenna Unit
The antenna unit includes an antenna pedestal inside a radome
assembly unit. The pedestal consists of a satellite antenna main dish with
RF components mounted on a stabilized pedestal. The radome protects
the antenna pedestal assembly unit from the severe marine environment.
Figure 2. Antenna Unit
4
V110 – Marine Satellite Communication System
Antenna Control Unit (ACU)
The Antenna Control Unit (ACU) provides the power to the antenna and
the BUC (block upconverter) for controlling the various settings of the
antenna. The digital VFD (Vacuum Fluorescent Display) allows for easy
operation of the ACU, even in the dark.
Front Panel
Rear Panel
Figure 3. Antenna Control Unit
The functions of the ACU are as follows,
System startup.
Setting the satellite.
Editing satellite information.
Setting the antenna parameter.
Setting the antenna manual search.
Setting the LNB local frequency.
Setting radiation hazard or blockage zone.
Setting modem connections
Setting GPS and Gyrocompass.
Display versions.
Display power status.
Performing diagnostic tests.
Backup the system settings.
Restore the system.
Set up the interface with a PC.
Installing the Antenna
5
Installation Kit
Contains the items required for securing the antenna unit and ACU to
the vessel.
Antenna Size Q’ty Remark
Hex. Bolt M12x60L 5EA
Hex Head
Wrench
M6x40L 5EA
Bolt
Dome
Was her
Flat
Was her
Spring
Was her
M6 5EA
M12 5EA
M12 5EA
Hex. Nut M12 10EA
ACU Size Q’ty Remark
Ta p p i n g
Screw
Flat Head
Screw
Sem’s
Bolt
Ø4x16 5EA
M3x8L 10EA
M3x12L 5EA
Figure 4. Installation Kit Components
Antenna-Deck
Ta b l e M o u n t B r ac k et-
Ta b l e
Rack Mount Bracket-
ACU
Ta b l e M o u n t B r a c k e t-
ACU
6
V110 – Marine Satellite Communication System
Other Components
Item Image Description Size Q’ty Remark
Rack - 2EA ACU-19inch Rack
ACU
1
Bracket
Table - 2EA ACU-Table
2
3
4.
5
6
7.
8.
9.
10
11
RG6 Cable 3m 1EA
ACU(MODEM RX) to
Modem
Antenna(MODEM IN)
RG6 Cable 15m 2EA
BUC Power
Cable
AC Power Cord
( CEE7/7)
1.5m 1EA ACU Power
15m 1EA
to Modem &
Antenna(ACU RX)
to ACU(ANT RX)
Antenna (BUC IN) to
ACU (BUC POWER)
PC Serial Cable 1.8m 1EA ACU to PC
USB Cable
(A-A / M-M)
iDirect
Interface Cable
1.8m 1EA ACU to PC
1.5m 1EA ACU to Modem
D-Sub
9 Pin Male
Connector
Gyro NMEA /
BUC Power
Connector
AK950-2 3EA
2EA ACU
ACU(Gyro NMEA /
BUC Power ) &
Antenna (BUC IN)
Install CD
- 1EA -
Installing the Antenna
7
12
13
Manual - 1EA -
Mounting
Te mp la te
Unpack Wooden
14
Crate Instruction
Guide
Figure 5. Component Box Parts List
- 1EA -
- 1EA -
8
V110 – Marine Satellite Communication System
Tools Required for Installation
Power Drill
Cross-Head
Screwdriver
Minus-Head
Screwdriver
Φ13mm Drill Bit
11mm Spanner
13mm Spanner
19mm Spanner
4mm
Allen key
Pencil
Figure 6. Tool Sets for Installation
Installing the Antenna
5mm
Allen key
9
Planning the Installation
Selection of Antenna Installation Site
Install the antenna in accordance with the following procedures to insure
maximum performance of the
antenna. The ideal antenna site has
a clear view of the horizon or
satellite all around. Please be sure
there are no obstacles within 15
degrees above the antenna. Any
obstacles can prevent the antenna
from transmitting and receiving
the satellite signal.
Do not install the antenna near by the radar especially on the same
plane as their energy levels may overload the antenna front-end circuits.
It is recommended to position the antenna at least 4 feet (1.2m) above
or below the level of the radar and minimum of 15 feet (4.6m) away
from the high power short wave radars.
The mounting platform should be rigid enough and not subjected to
excessive vibration. The movement of the antenna can be minimized by
installing at the center of the vessel. If these conditions can be only
partially satisfied, find the best compromised installation site between
the various considerations.
10
V110 – Marine Satellite Communication System
Antenna Unit
Figure 7. Elevation Limit of Obstacles
15°
Obstacle
Configure Radiation Hazard/Blockage Zones
It is important to setup the radiation hazard or blockage zones for
Intellian VSAT TX/RX communication systems. (See the “Block Zone
Setting” section of this manual). The ACU can be programmed with
relative azimuth and elevation sectors to create up to five zones where
transmit power would endanger personnel who are frequently in that
area or blockage exists. Several things happen when the antenna is
within one of these zones.
1. “BLOCK” will be displayed on the ACU screen.
2. Tracking continues as long as the signal level is greater than the
predefined threshold value. When the signal level drops below
the threshold value the antenna will wait “Search Wait Time”
parameter amount of time and re-target the satellite you
targeted last. The antenna will continue to re-target the satellite
until the satellite is re-acquired and tracking can be resumed.
3. A transmit inhibit output from the ACU will disable/mute the
modem transmit
Installing the Antenna
11
System Cables
Before installing the system cables, you need to take the following
points into consideration.
All cables need to be well clamped and protected from physical
damage and exposure to heat and humility.
Cable with an acute bend is not allowed.
Where a cable passes through an exposed bulkhead or deck
head, a watertight gland or swan neck tube should be used.
RF Cables (Customer Furnished)
Due to the voltage losses across the length of the RF coaxes at L-Band,
Intellian recommends the following 75 ohm coax cable types for
standard system installations. For cable runs longer than 70 meter,
please consult Intellian Technologies.
Run Length Coaxial Cable Type
Up to 30 meters RG-6 or LMR-300-75
Up to 70 meters RG-11 or LMR-400-75
Up to 120 meters LMR-600-75
Figure 8. Recommended RF Cables
Gyro Compass / GPS Interface Cable (Customer Furnished)
Type Multi-conductor, Shielded
Number of wires 4 Conductors for Step-By-Step Gyro
5 Conductors for Synchro
2 Conductors for NMEA
Figure 9. Recommended Gyro/ GPS Cables
BUC Power Cable
Cable Length mm2 per conductor
Up to 30m 1.25mm2
Up to 50m 2mm2
Up to 70m 2.5mm2
Up to 100m 3.5mm2
Figure 10. Recommended BUC Power Cables
Power Requirements
Intellian v110 has been designed to work on a vessel’s power supply
rated at 90-260 V AC.
12
V110 – Marine Satellite Communication System
Preparing the Installation
Unpack the v110 box
The antenna pedestal is shipped completely assembled in its radome.
Remove the four shipping blots which mount the antenna to the pallet.
The pallet should be lifted by means of suitable sized lifting equipment.
(Refer to the supplied instruction guide for details on how to unpack
wooden crate of v110.)
19mm Spann er
Figure 11. Remove 4 bolts from the bottom of the box
Installing the Antenna
13
Antenna Dimension
The method of installation and mounting of antenna may vary with
vessel design but the following procedures are applicable in most
situations, and will result in a secure and effective installation. Confirm
the height and diameter the antenna before installing it.
151.7cm
(59.7”)
Ø146.8cm
(57.8”)
Figure 12. Radome Dimension
14
V110 – Marine Satellite Communication System
Antenna Mounting Hole Pattern
The mounting holes must be in the exact same place as shown in the
diagram below.
ø48cm (18.9”)
24.7 cm (9.7”)
Ø48cm(18.9”)
24.7cm (9.7”)
4-Ø14
HOLES
Figure 13. Dimension of Mounting Hole Pattern
V110 Rad ome
Bottom
ø48cm (18.9”)
Figure 14. Dimension of Mounting Plate
Installing the Antenna
15
Preparing Antenna Supporting Pole
Base Panel (10t)
Cabl e Entry
200 (7.8 ”)
1,000~1, 500 (4 0~60 ”)
150 (5.9”)
Unit: mm/inch
Figure 15. Recommended Dimension of Mounting Pole
WARNING: Ensure that cables have been run through watertight fittings to
prevent water entry into the vessel when the installation is
completed. The coax cables must be inserted through the cable
strain relief(s) at the base of the radome.
16
V110 – Marine Satellite Communication System
Remove Antenna Shipping Constraints
Open the radome hatch and remove the web strap
from the pedestal as shown in the photo below. Do not turn on the
antenna if the shipping restraints from the antenna pedestal have not
been removed completely.
and tiewrap
Step 1
Step 2
Installing the Antenna
17
Step 3
Step 4
18
V110 – Marine Satellite Communication System
Step 5
Step 6
Installing the Antenna
19
Step 7
Step 8
20
V110 – Marine Satellite Communication System
Radome Hatch
Figure 16. Open Radome Hatch before Removing Web Strap
WARNING: The elevation and cross-level motor breaks prevent dish
damage while the antenna is in power off mode. However,
Intellian strongly recommends to restraint the antenna pedestal
properly during underway conditions when power is removed
from the antenna. The normal operating condition for the v110
is to remain powered up at all times.
Mounting the Radome
Bolt the Radome base directly to the ship’s deck or mounting plate (flat
mounting area).
M12 H ex. Bolt
Antenna Unit
Deck
M12 Flat Washer
M12 Sp ring Wash er
M12 Hex. Nut
19mm S panner
Figure 17. Mounting the Radome Diagram
Installing the Antenna
21
Installing the System Cables
The coax cables must be inserted through the cable strain relief(s) at the
base of the radome. The cables must be routed from the antenna
through the deck and through various ship spaces to the antenna
control unit. When pulling the cables in place, avoid sharp bends,
kinking, and the use of excessive force. After placement, seal the deck
penetration glad and tie the cables securely in place.
Cable
Entry
Rear View
Figure 18. Cable Entry
Shrin kage Guide
Rubber Gland
Figure 19. Cable Entry Diagram
22
V110 – Marine Satellite Communication System
RF Cable Connections
Ensure that the power switch is off during the installation period and all
the cables are connected properly between the antenna control unit and
the power switch box. When all the hardware and cable have been
installed, turn on the power switch. Use RG11 rubber gland if you’re
using RF11 cable instead of RG6 supplied by Intellian.
Modem Tx Cable
(From outsi de)
ACU Rx Cabl e
(From out side)
BUC P ower Cabl e(IN)
(Fro m ACU)
Antenna P ower Cab le
(From Antenna)
Rotary #1
Tx Ca bl e
(From Antenna )
On/ Of f Switch
Front View
Rotary #2
Rx Cab le
(From Antenna)
BUC Po wer Cab le( OU T)
(From Antenna)
Figure 20. Cable Connections on Power Switch Box
Installing the Antenna
23
Installing the ACU
ACU Dimensions
47.32 cm(18.6”)
45.32 cm(17.8”)
43 cm(17”)
20cm (7.9”)
13cm (5.1”)
48.43cm (19”)
46.5cm (18.3”)
3.18cm (1.3”)
Figure 21. Dimension of ACU
Selection of ACU Installation Site
The ACU should be installed below deck, in a location that is:
Dry, cool, and ventilated.
The front panel should be easy accessible to user.
38cm (15”)
4.4cm (1.7”)
24
V110 – Marine Satellite Communication System
Installing the ACU
Intellian supplies two type of mounting methods (a)19” Rack Mount
Type and (b)Table Mount Type to mount your ACU.
19” Rack Mount Type
The ACU should be installed using the two supplied Rack
Mounting Brackets which allow for a side 19” rack mounting
configuration.
Using the self tapping screws supplied, attach the mounting
brackets to the sides of the ACU.
Place the ACU in the location where it is going to be installed.
Connect the cables to the rear of the ACU.
Table Mount Type
The ACU should be installed using the two supplied Table
Mounting Brackets which allow for a top or bottom mounting
configuration.
Using the self tapping screws supplied, attach the mounting
brackets to the sides of the ACU.
Place the ACU in the location where it is going to be installed.
Using a pencil to mark the 4 hole positions (2 each side), and
use the appropriate drill bit to drill them.
Connect the cables to the rear of the ACU.
Figure 22. 19 inch Rack Mount Type Figure 23. Table Mount Type
WARNING: Ensure that the installed cables are longer enough to take out
the ACU from the rack.
Installing the ACU
25
Connecting the System to a Ship’s Gyro
For satellite tracking, you must connect a ship’s Gyro to the antenna
system through the gyro interface on the rear of the ACU. Intellian’s ACU
supports three different gyro types, Step-by Step (SBS), Synchro and
NMEA 0183.
SBS/ Synchro/ NMEA 0183 Gyro Compass Interface Cable (Customer
Furnished)
Type: Multi-conductor (4 conductors for SBS, 5 conductors for Synchro,
and 2 conductors for NMEA 0183).
Groun d (-)NMEA out (+)
Figure 24. Ship’s Gyro Connection
WARNING: Determine the type of gyrocompass OUTPUT on the ship,
assure that the GYRO TYPE parameter is set correctly (refer to
the operation section of this menu).Heading in most cases will
be 000.0 and you will have to enter the initial value of ships
current value whenever you turn on the ACU. The ship’s
heading is not required to input when your system is
connected to a 1:1 Synchro or NMEA 0183 Heading
26
Gyrocompass output.
V110 – Marine Satellite Communication System
ACU Connector Guide
Synchro/SBS Connector
ACU Synchro/ SBS Port
D-Sub 9pin Female
Pin Signal Pin Signal
1 SBS_COM 6 SBS_C
2 SBS_B 7 SBS_A
3 SYNCHRO_R2 8 SYNCHRO_R1
4 SYNCHRO_R3 9 SYNCHRO_S2
5SYNCHRO_S1
D-Sub 9pin Male connector
Supplied Component (Ref. page 7)
Control Connector
ACU Consol Port
D-Sub 9pin Female
Pin Signal Pin Signal
1GND6GPSOUT-
2 GPS OUT + 7 MODEM_SIGNAL_IN
3 MODEM_LOCK 8 MODEM _CTRL2
4
5GPSIN +
MODEM_CTRL1
(TX MUTE)
D-Sub 9pin Male connector
Supplied Component (Ref. page 7)
9GPS IN-
Installing the ACU
27
Operating the ACU
Introduction
This section of the handbook describes how to setup your system after
installing the ACU. It includes the following functions:
Normal Mode
System Startup
Monitoring Current Status
Setup Mode
Installation Setting
Select Satellite
Setting GPS and Gyrocompass
Setting Bow Adjustment
Setting Modem Connection
Setting LNB Local Frequency
Setting the Antenna
Setting Antenna Manual Search
Setting Antenna LNB Skew Angle
Setting Antenna Search Parameters
Setting Antenna Parameters
Setting Block Zone
Performing Diagnostic Tests
Setting the Satellite
Load Satellite
Edit Satellite Information
Add Satellite
Setting the System
Setting LNB Local Frequency
Setting GPS and Gyrocompass
28
V110 – Marine Satellite Communication System
Setting Modem Port
System Backup & Restore
Display Versions
WARNING: Many of the above functions will only be required only after
initial installation of your system.
Operating the ACU
29
ACU Soft Keys
MODE
PC
CABLE (USB)
STATUS
LED S
RETURN
Figure 25. ACU Soft Keys
Soft key Fucntion
MODE Enter Setup mode
RETURN
FUNCTION Save the adjusted settings.
ARROW
KEYS
OK To enter next step/ menu
NUMBER
KEYS
Figure 26. Soft Key Functions
Return to previous menu / option or save the
adjusted settings.
Select from the alternative options/ To Increment or
decrement the selected character to the desired
value.
To input the numbers
FUNCTION
ARROW
KEYS
NUMBE R
KEYS
30
V110 – Marine Satellite Communication System
Normal Mode
Startup
With the system installed and power applied, the ACU screen will show
the following sequence.
INTELLIAN TECHNOLOGIES INC.
Antenna Control Unit
1. The data commu nication is bein g established between the antenna and the ACU.
M
R
F
1
2
3
OK
←
4
5
6
0
7
8
9
·
INITIALIZE - ANTENNA INFO
INTELLIAN V110
Antenna Control Unit
2. The ACU receives antenn a information.
INITIALIZE - EL POSITION
INTELLIAN V110
Antenna Control Unit
3. The el evation angle is in iti alized.
INITIALIZE - AZIMUTH POSITION
4. The azimu th angle is initialized.
5. The an tenna returns to the targeted satellite position.
◀
SEARCH2 113.0E KOREA_5 SIG:301 VL
AZ:202.7( 202.7) EL: 48.3 SK:-72.0
INTELLIAN V110
Antenna Control Unit
INITIALIZE – SAT POSITION
INTELLIAN V110
Antenna Control Unit
Antenna Control Unit
M
R
F
M
R
F
M
R
F
M
R
F
1
2
3
OK
OK
OK
OK
←
4
5
6
0
7
8
9
·
1
2
3
←
4
5
6
0
7
8
9
·
1
2
3
←
4
5
6
0
7
8
9
·
1
2
3
←
4
5
6
0
7
8
9
·
M
▶
R
F
1
2
3
OK
←
4
5
6
0
7
8
9
·
6. The an tenn a is search ing for current satellite.
◀
TRACKING 113.0E KOREA_5 SIG:501●VL
AZ:202.7( 202.7) EL: 48.3 SK:-72.0 Fn
Antenna Control Unit
7. The an tenn a has locked onto current satellite and is now tracking.
M
▶
R
F
Operating the ACU
1
2
3
OK
←
4
5
6
0
7
8
9
·
31
Monitoring Antenna Current Status
While the ACU power is on, it displays the status of the antenna. The
current status of the antenna is displayed as shown below.
◀
SEARCH2 113.0E KOREA_5 SIG:301 VL
AZ:202.7( 202.7) EL: 48.3 SK:-72.0
Ant enna Cont rol Uni t
1. Th e antenna is searching for current satellite.
M
▶
R
F
1
2
OK
3
4
5
6
7
8
9
←
0
·
◀
TRACKING 113.0E KOREA_5 SIG:301●VL
AZ:202.7( 202.7) EL: 48.3 SK:-72.0 Fn
Ant enna Cont rol U nit
2. The antenna is tracking current satellite.
True azimu th [ 202.7 ] position of the an tenn a is the sum of ships heading 000.0 [ HDG ]
an d an tenn a relati ve [ 20 2.7 ]. C urren t IF signal level (SIG/ A GC) i s di splayed . ● will
be only displayed when signal is strong enough to lock onto the satellite. [VL] refers to
vertical low. Local frequency is decided by the supplied voltage from the LNB.
SAVE CURRENT SAT INFO ?
→ YES NO
Ant enna Cont rol Uni t
3. Press FUNCTIONkey to save cu rrent satellite information or abort and return to the
main display.
◀
TRACKING 113.0E KOREA_5 SIG:301●VL
AZ:202.7( 202.7) EL: 48.3 SK:-72.0 Fn
Ant enna Cont rol U nit
4. While the antenna is tracking the satellite, press RIGHT arrow key to display NBD ,
GPS and ship’s heading information.
◀
NBD F:1247000 BW: 1000 SIG:301
004.53E 52.22N HDG:000.0 L:10000 Fn
Ant enna Cont rol U nit
5. NBD, GPS and ship’s heading information are shown.
- NBD (Narrow Band Detector) Frequency : 1247000 KHz (IF Frequency)
- Band Width : 1000KHz
- SIG (Signal Level ): 301
- LNB LO. frequen cy : 10000 MHz (13V+0KHz)
- HDG (Ship’s Heading) : 000.0
- W (West ) / E (East) Lon gi tu de : 4.53E
- N (N orth) / S (Sou th ) Latitude : 52.22N
●▶
M
▶
R
F
M
R
F
M
▶
R
F
M
R
F
1
2
OK
OK
OK
OK
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
1
2
3
←
4
5
6
0
7
8
9
←
0
·
←
0
·
←
0
·
·
32
V110 – Marine Satellite Communication System
◀
[PWR] ANT: 26.4V LNB: 13V + 0KHz
ACU: 27.1V
Ante nna Cont rol Unit
6. Press RIGHT arrow key to display ACU operation voltage , anten na operation
voltage and LNB voltage supplied information.
- VL (Vertical Low) : 13V+0 KHz
- HL (Horizontal Low) : 18V+0KHz
- VH (Vertical High) : 13V + 22KHz
- HH (Horizontal High) : 18V+22KHz
M
▶
OK
R
F
1
2
3
←
4
5
6
0
7
8
9
·
◀
V1-11426 ANT. Serial 1.00
VP-T100 ACU Serial 1.00(1.00)
Ante nna Cont rol Unit
7. Press RIGHTarrow key to display system firmware and library versions.
ANT Serial : An tenna Serial Nu mber, 1.00 (PCU Version)
ACU S erial : Anten na Con trol Un it Se rial N umber, 1.00 (ACU Main version ), (1.00)
(Library versi on)
M
▶
R
F
1
OK
4
7
2
3
←
5
6
0
8
9
·
Operating the ACU
33
Setup Mode
To enter the Set-up Mode simply follow the instructions below.
◀
TRACKING 113.0E KOREA_5 SIG:301●VL
AZ:202.7( 202.7) EL: 48.3 SK:-72.0 Fn
Ant enna Cont rol Uni t
1. While the anten na is searching / tracking , press MODE key for setup mode.
M
▶
OK
R
F
1
2
3
←
4
5
6
0
7
8
9
·
→ YES NO
SETUP MODE ?
Ante nna Cont rol Unit
2. Press LEFTkey to move cu rsor to YES and press OK key to enter setup mode or
press RIGHT key to move cursor to NO an d press OK key to abort and return to th e
main display.
M
R
F
1
OK
2
4
5
7
8
3
←
6
0
9
·
34
V110 – Marine Satellite Communication System
Installation Settings
During the first time installation, it is required to setup the installation
settings.
→ YES NO
SETUP MODE ?
Antenna Control Unit
1.Press LEFT arrow key to move cursor to YES and press OK key to enter setup mode.
M
R
F
1
2
OK
3
4
5
6
7
8
9
←
0
·
+ANTENNA +SATELLITE
+SYSTEM →+INSTALLATION
Antenna Control Unit
2. Press arrow keys to move cursor to INSTALLATION an d press OK key to enter
INSTALLATION menu.
▲ [1] KOREA_5 113E ▼
3. Press UP and DOWN arrow keys to select the satellite that you wish to track and
press OK key to load the selected satellite.
LATITUDE LONGITUDE HEADING
7.00N ▼ 126.53E 000.0
▲ 3
4. Set LA TITUDE, L ONG I TUDE and SHIP’S HEADING
Press LE FT and RIGHT arrow keys until th e desired character is un derscored
(selected). Press UP and DOWN arrow keys to in crease or decrease the value.
Or press NUMBERkeys to set the desired value directly.Press OK key to set the
parameter.
Entry of ships headin g is not required wh en your system is conn ected to a NMEA0813
or 1:1 Syn chro Heading Gyro Compass ou tput.
SELECT SATELLITE
Antenna Control Unit
Antenna Control Unit
M
R
F
M
R
F
M
R
F
1
OK
OK
OK
2
4
5
7
8
1
2
4
5
7
8
1
2
4
5
7
8
3
←
6
0
9
·
3
←
6
0
9
·
3
←
6
0
9
·
Operating the ACU
35
GYRO TYPE BOW ADJUST MODEM PORT
▲ NMEA ▼ 000 ETHERNET
Ant enna Cont rol Uni t
5. Set GYRO T YPE , BOW ADJUST and M ODEM PORT
Gyro type i s to determin e th e type of gyro compass that i s used on the shi p.
Ensure th at the Gyro Type1) is set correctly.
Bow adjust is to offset th e angle dif ference between the an tenna’s bow and
the ship’s bow. Variations from actual alignment can be compensated with this
parameter, so precise align ment is not required.
Modem port 2) is to determine the type of modem communication port on the antenna
con trol u ni t that i s u sed to i nterf ace with the satell ite mode m.
Press UP and DOWN arrow keys to select th e correct parameter and press OK key
to set th e parameter.
Gyro Type 1)
- None
-NMEA
- Synchro 1:1
- Synchro 36:1
- Synchro 90:1
- Synchro 360:1
Modem Port 2)
- Eth ern et
-RS422
-RS232
13V+0KHz 18V+0KHZ
0000MHz ▼ 11300MHz
▲ 1
Ant enna Cont rol Uni t
M
R
F
M
R
F
1
OK
OK
2
4
5
7
8
1
2
4
5
7
8
3
←
6
0
9
·
3
←
6
0
9
·
13V+22KHz 18V+22KHz
▲ 1
1300MHz ▼ 09750MHz
Ant enna Cont rol Uni t
6.Set the LNB local frequency f or each voltage power. (13V+0KHz, 18V+0KHz,
13V+22KHz ,18V+22KHz)
Press LEFT and RIGHT arrow keys until th e desired character is un derscored
(selected). Press UPand DOWN arrow keys to in crease or decrease the value.
Or press NUMBERkeys to set the desired value directly.
M
OK
R
F
36
V110 – Marine Satellite Communication System
1
2
3
←
4
5
6
0
7
8
9
·
→ YES NO
LOAD ?
Ant enna C ontrol Unit
7. Press RETURNkey to load the current setting or abort an d return to the main
display.
M
OK
R
F
1
2
3
←
4
5
6
0
7
8
9
·
LOADING . . .
DO NOT TURN OFF !
Ant enna C ontrol Unit
8. Setting is being loaded to the system.
The ACU will re start the system au toma tical ly after u ploadin g th e setti ng.
DO NOT TURN OFF ACU POW ER wh ile uploading is being processed.
◀
TRACKING 113.0E KOREA_5 SIG:301●VL
AZ:202.7( 202.7) EL: 48.3 SK:-72.0 Fn
Ant enna C ontrol Unit
9. Antenna information has been u pdated.
●●●○○○○○○○○○○○○
M
R
F
M
▶
R
F
1
2
3
OK
OK
←
4
5
6
0
7
8
9
·
1
2
3
←
4
5
6
0
7
8
9
·
Operating the ACU
37
Antenna Settings
Manual Search
→ YES NO
SETUP MODE ?
Antenna Control Unit
1. Press LEFTkey to move cursor to YES and press OK key to enter setup mode.
M
R
F
1
OK
4
7
2
3
←
5
6
0
8
9
·
→+ANTENNA +SATELLITE
+SYSTEM +INSTALLATION
Antenna Control Unit
2. Press OK key to enter ANTENNA menu.
◀
→
+MANUAL SEARCH +SET SKEW
+SEARCH PARAM +SET PARAMETERS
Antenna Control Unit
3. Press OK key to en ter MANUAL SEARCH menu.
STEP SIZE AZIMUTH ELEVATION AGC
# 0
0.2 # ◀ 231.7▶▲48.3 ▼ 301 Fn
Antenna Control Unit
4. Cu rren t IF signal level (AGC) / (SIG) is displayed to assist you in manu ally peaking EL
for best signal level. Press NUMBERkey to ch ange the step size. (Range : 0.1~99.9)
Press LEFT and RIGHT arrow keys to move azimu th by step size. (Range : 0~360)
Press UP and DOWN arrow keys to move elevation by step size. (Range : 0~90)
Press FUNCT ION key to save current value or abort an d return to the main display.
SAVE CURRENT SAT INFO?
→ YES NO
Antenna Control Unit
5. If the current settings are able to locate the satellite, press FUNCTION key to save
“current satellite information”. It will shorten the satellite acquisition time next time.
Press LEFT key to move cursor to YES and press the OK key to save the settin gs.
M
R
F
M
▶
R
F
M
R
F
M
R
F
1
2
OK
OK
OK
OK
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
←
0
·
←
0
·
←
0
·
←
0
·
38
V110 – Marine Satellite Communication System
Setting Antenna LNB Skew Angle
→ YES NO
SETUP MODE ?
Antenna Control Unit
1. Press LEFT key to move cursor to YES and press OK key to en ter setup mode.
M
OK
R
F
1
2
3
←
4
5
6
0
7
8
9
·
→+ANTENNA +SATELLITE
+SYSTEM +INSTALLATION
Antenna Control Unit
2. Press OK key to en ter ANTENNA menu.
◀
+MANUAL SEARCH →+SET SKEW
+SEARCH PARAM +SET PARAMETERS
Antenna Control Unit
3. Press RIGHT arrow key to move cu rsor to SET SKEW and press OK key to
enter SET SKEW menu.
▲ CALIBRATION ▼
4. Press UP and DOWN arrow keys to select the skew type an d press OK key
to run the selected operation ‘ CALIBRATION ‘ or ‘ MANUAL ‘. Select MANUAL to
control LNB skew angle manually. If you replace the control board , skew
potentiometer or bel t , select CALIBR ATION to calibrate LN B skew an gle.
▲ 20 ▼
5. Press UP and DOWN arrow keys to in crease or decrease the LNB skew angle
manually and the corresponded SIGNAL level will be displayed next to it.
Press RETURN key to retu rn to th e m ain di splay.
SELECT SKEW TYPE
Antenna Control Unit
SKEW SIGNAL: 180
Antenna Control Unit
M
OK
R
F
M
▶
OK
R
F
M
OK
R
F
M
OK
R
F
1
2
3
←
4
5
6
0
7
8
9
·
1
2
3
←
4
5
6
0
7
8
9
·
1
2
3
←
4
5
6
0
7
8
9
·
1
2
3
←
4
5
6
0
7
8
9
·
Operating the ACU
39
Setting Antenna Search Parameter
These parameters should only be changed by an authorized service
technician. Improper setting of these parameters will cause your system
to perform improperly.
→ YES NO
Ant enna C ontrol Unit
1. Press LEFTkey to move cursor to YES and press OK key to enter setup mode.
SETUP MODE ?
M
R
F
1
2
3
OK
←
4
5
6
0
7
8
9
·
→+ANTENNA +SATELLITE
+SYSTEM +INSTALLATION
Ant enna C ontrol Unit
2. Press OK key to enter ANTENNA menu.
◀
+MANUAL SEARCH +SET SKEW
→+SEARCH PARAM +SET PARAMETERS
Ant enna C ontrol Unit
3. Press DOWN arrow keys to move cursor to SEARH PARA M an d press OK key to
enter SEARCH PA RA M menu.Press the LEFT and RIGHT arrow keys to select the
parameter you wish to edit. Press OK key to edit parameter. Or press RETURN key
again to return to th e main display.
SEARCH WAIT TIME INCREMENT STEP
▲ 0
4. Set SEARCH W A I T TIME and I NCREMENT STEP
Set the time-out for au tomatic in itiation of a search after th e signal level drops below
the pre-defined th reshold value (Ran ge : 1 - 120 sec) an d set in crement step size.
(Range : 0.01 – 5.00 sec)
Press LEFT and RIGHT arrow keys u ntil th e desired character is u nderscored
(selected). Press UP and DOWN arrow keys to increase and decrease the selected
character. Or press NUMBER keys to set the desired valu e directly. P ress OK key to
set th e parameter and set next param eter. Press RETURN key to select the parameter
you w ish to edit and press RETURNkey again to save or abort and return to th e main
display. .
30 ▼ 0.80
Ant enna C ontrol Unit
M
R
F
M
▶
R
F
M
R
F
1
OK
OK
OK
2
4
5
7
8
1
2
4
5
7
8
1
2
4
5
7
8
3
←
6
0
9
·
3
←
6
0
9
·
3
←
6
0
9
·
40
V110 – Marine Satellite Communication System
SEARCH2 AZ SEARCH2 EL
▲ 0
06 ▼ 06
Ant enna Co ntrol Unit
M
R
F
1
2
3
OK
←
4
5
6
0
7
8
9
·
SEARCH3 AZ SEARCH3 EL
▲ 0
A search pattern wi ll automatically be in itiated when AGC/SIG falls below the cu rrent
threshold setting (indicates that satellite signal h as been lost). Search is condu cted
in a two-axis pattern consistin g of al ternate movements in azim uth (AZ) and elevation
(EL) as f orm ing expandin g square indicated as below diagram.
Search 2 : a search pattern 2 will au tomatically be in itiated when AGC / SIG f alls below
the current detect level threshold value. Search 3: a search pattern 3 will au tom atically
be ini tiated wh en AGC / SIG falls below the current tracking level threshold value.
Azimuth (AZ) Range
1
5.Set th e SEA RCH 2 and 3 A (Az imuth) range(Range : 0 – 360) and set the
SEARCH 2 and 3 EL (Eleva ti on) range. (Ran ge : 0 -90)
Press LEFT and RIGHT arrow keys until the desired character is underscored (selected).
Press UP and DOWN arrow keys to increase and decrease the selected character. Or
press NUMBER keys to set the desired value directly. Press OK key to set th e
parameter and set n ext parameter. Press RETURNkey to select the parameter you
wish to edit an d press the RETURN key again to save or abort an d return to the m ain
display.
03 ▼ 04
Ant enna Con trol U nit
Elevation
(EL)Ran ge
M
R
F
OK
Peak Level
Trackin g Level
Detect Level
Noise Level
1
2
3
4
5
6
7
8
9
←
0
·
Operating the ACU
41
Setting Antenna Parameters
These parameters should only be changed by an authorized service
technician. Improper setting of these parameters will cause your system
to perform improperly.
→ YES NO
Ante nna Cont rol Unit
1. Press LEFT key to move cursor to YES and press OK key to en ter setup mode.
SETUP MODE ?
M
R
F
1
2
3
OK
←
4
5
6
0
7
8
9
·
→+ANTENNA +SATELLITE
+SYSTEM +INSTALLATION
Ante nna Cont rol Unit
2. Press the OK key to en ter A NTENNA menu.
+MANUAL SEARCH +SET SKEW
+SEARCH PARAM →+SET PARAMETERS
Ante nna Cont rol Unit
3. Press arrow keys to move cursor to SET PRAMETERS men u and press OK
key to enter SET PARA METERS menu.
ENTER PASSWORD
----
Ante nna Cont rol Unit
4. Press 4-digit password to en ter SET PRAM ETERS menu. (1590)
Access to the password protected system. Setup parameters is only required after
installation or repairs of your antenn a system. These parameters sh ould on ly be
changed by an authorized service tech nician. Improper setting of these parameters
will cause your system to perform improperly.
M
R
F
M
R
F
M
R
F
1
OK
4
7
1
OK
4
7
1
OK
4
7
2
3
←
5
6
0
8
9
·
2
3
←
5
6
0
8
9
·
2
3
←
5
6
0
8
9
·
42
V110 – Marine Satellite Communication System
DETECT LEVEL TRACKING LEVEL
▲ 0
5. Set DETECT LEVEL and TRACKING LEVEL when ch oose DVB on tracking
signal. (Range : 1-200)
The detect level is to set the satellite signal detection level and th e tracking level is to set
the satelli te sign al tracking level.
Press LEFT and RIGHT arrow keys until the desired character is underscored (selected).
Press UP and DOWN arrow keys to increase and decrease the selected character. Or
press NUMBER keys to set the desired value directly. Press OK key to set th e
parameter. Press RETURN key to select the parameter you wish to edit an d press
RETURNkey again to save or abort an d return to the main display.
40 ▼ 020
Ant enna C ontrol Unit
M
R
F
1
2
OK
3
4
5
6
7
8
9
←
0
·
DETECT NBD LEVEL TRACKING NBD
▲ 0
6. Set DETECT NBD LEVEL and TRA CKING NDB wh en choose NBD on tracking
signal. (Range : 1-200)
The detect level is to set the satellite signal detection level and th e tracking level is to set
the satelli te sign al tra ckin g leve l.
Press LEFT and RIGHT arrow keys until the desired character is underscored (selected).
Press UP and DOWN arrow keys to increase and decrease th e selected character. Or
press NUMBER keys to set th e desired value directly. Press OK key to set the
parameter. Press RETURNkey to select the parameter you wish to edit an d press
RETURN key again to save or abort an d return to th e main display.
40 ▼ 020
Ant enna C ontrol Unit
M
R
F
1
2
OK
3
4
5
6
7
8
9
Peak Level
Tra ck in g Le ve l
Detect Level
Noise Level
←
0
·
Operating the ACU
43
BOW ADJUST EL.ADJUST
00 ▼ +0.0
▲ 0
Ante nna Control Unit
7. Set BOW ADJUST and EL. ADJUST
The bow adjust is to offset the an gle difference between the an tenna’s bow and th e
ship’s bow (Ran ge :0 – 360°) and the elevation adjust is to offset the angle difference
between th e mechan ical elevation an gle an d actual elevation an gle (Range : ± 5°).
Press LEFT and RIGHT arrow keys until the desired character is underscored (selected).
Press UP and DOWN arrow keys to increase and decrease the selected character. Or
press NUMBER keys to set the desired value directly. Press OK key to set th e
parameter. Press RET URN key to select the parameter you wish to edit an d press th e
RETURN key again to save or abort and return to the main display.
BOW AUTO SAVE EXT.LOCK ACTIVE
▲ YES ▼ LOW
Ant enna Con trol U nit
8. Set BOW AUTO SAVE an d EXT . LO CK A CTIVE
The bow auto save is to save BOW information automatically. This function will be
activated wh en the antenn a finds peak position.
Ext. lock active here is referred that modem lock output from the modem provides a logic
inpu t via a voltage to the ACU to identify wh en it is on the correct satellite. Th is setting
can be varied f rom modem to m odem. (Refer to th e m odem manu al for detail s.)
Press UP and DOWN arrow keys to select th e parameter option s. Press OK key to set
the parameter. Press RETURN key to select the parameter you wish to edit and press
RETURN key again to save or abort and return to th e main display.
M
R
F
M
R
F
1
2
OK
OK
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
←
0
·
←
0
·
44
V110 – Marine Satellite Communication System
TX MUTE ACTIVE +TILT BIAS
▲ LOW ▼
Ante nna Contr ol Unit
9. Set TX M UTE A CTI V E
A transmit in hibit out put from the ACU will disable/mu te the modem transmit via a
voltage when ever the antenna is blocked, searchin g, or is mis-pointed 0.5 degrees from
peak satellite position. Th is setting can be varied from modem to modem. (Refer to the
modem m anual for details.)
Press UP and DOWN arrow keys to select HIGH or LOW. Press OK key to set the
parameter. Press RETURN key to select th e parameter you wish to edit and press
RETURN key again to save or abort and return to th e main display.
M
R
F
1
2
OK
3
4
5
6
7
8
9
←
0
·
STEP SIZE ELEVATION CROSS LEVEL
.2 # ▲ 00.0 ▼◀01.0 ▶
# 0
Ante nna Contr ol Unit
10. Set TI L T BI A S OF F SE T
The tilt bias is required to set when the control board, skew potentiometer or belt is
replaced. Check and see if the bubble is in the center of th e circular bubble level vial .
If not, press OK key to en ter TI L T B I AS menu to adju st elevation an d cross-level
angles.
Press NUMBERkeys to set the step size. Press LEFT and RIGHT arrow keys to
move CRO SS LEVEL OFFSET by step size. Press UP and DOW N arrow keys to
move ELEV A TIO N OFFSET by step size. Press RETURNkey to save or abort and
retu rn to th e m ain displ ay.
M
R
F
1
OK
2
4
5
7
8
3
←
6
0
9
·
Operating the ACU
45
Setting Block Zones
Up to 5 block or radiation hazard zones can be programmed with
relative azimuth and elevation sectors.
→ YES NO
SETUP MODE ?
Ant enna C ontrol Unit
1. Press LEFTkey to move cursor to YES and press OK key to enter setup mode.
M
R
F
1
2
3
OK
←
4
5
6
0
7
8
9
·
→+ANTENNA +SATELLITE
+SYSTEM +INSTALLATION
Ant enna C ontrol Unit
2. Press OK key to en ter ANTENNA menu.
◀
→+BLOCK ZONE +DIAGONOSIS
Ant enna C ontrol Unit
3. Press arrow keys to move cursor to BLOCK ZONE and press OK key to en ter
BLOCK ZO NE m enu. Up to 5 block zones is allowed to be programmed.
ZONE 1 BLOCK
▲ ON ▼
Antenna Control Unit
◀
→AZ.1 START AZ.1 END EL.1 LIMIT
000 000 90
Ant enna C ontrol Unit
4. Set ZONE 1 BLOCK
Press UP and DOWN arrow keys to select “ON” to use ZONE 1 BLOCK or “OFF” to n o t
use ZONE 1 BLOCK. Press OK key to use ZO NE 1 BLOCK and set zon e 1 block range.
Press RETURN key to select the parameter you wish to edit and press th e
RETURN key again to save or abort and return to the main display.
Set th e AZ.1 S TAR T, AZ . 1 EN D and EL.1 LIMI T when ZONE 1 BLOCK is ON.
This is the clockwise of th e two points. AZ.1 START is wh ere th e relative
azimu th starts and AZ.1 END is where the relative azimu th en ds (Range: 0- 360°).
EL.1 Limit is wh ere the elevation starts (Range 0- 90°).
M
R
F
M
▶
R
F
M
R
F
M
▶
R
F
1
2
3
OK
OK
OK
OK
←
4
5
6
0
7
8
9
·
1
2
3
←
4
5
6
0
7
8
9
·
1
2
3
←
4
5
6
0
7
8
9
·
1
2
3
←
4
5
6
0
7
8
9
·
Press LEFT and RIGHT arrow keys until the desired character is un derscored (selected).
Press UP and DOWN arrow keys to increase and decrease the selected character. Or
Press NUMBER keys to set the desired valu e directly. Press OK key to set the
parameter. Press RETURNkey to select the parameter you wish to edit and press
RETURN key again to save or abort and return to the main display.
46
V110 – Marine Satellite Communication System
ZONE 2 BLOCK
▲ OFF ▼
Ant enna C ontrol Unit
5. ZONE 2 to Z ONE 5 BLOCK settin g i s sam e as Z ONE 1 B LOC K.
Press OK key to set th e n ew ZONE 2 BLOCK and set n ext parameter. Press RET URN
key to select the param eter you wish to edit and press RETURN key again to save or
abort and return to th e main display.
M
R
F
1
2
OK
3
4
5
6
7
8
9
←
0
·
→ YES NO
SAVE ?
Ant enna C ontrol Unit
6. Press LEFT arrow key to move cursor to YES and press OK key to save an d
execute the current settings. Or press RIGHT arrow key to move cu rsor to NOan d
press OK key to abort and return to the main display.
M
R
F
1
OK
4
7
2
3
←
5
6
0
8
9
·
Operating the ACU
47
Executing Antenna Diagnosis
It is possible to see the antenna status by reviewing the result of
diagnosis of the antenna. Refer to the following codes, to understand
the diagnosis results.
→ YES NO
Ant enna C ontrol Unit
1. Press LEFTkey to move cursor to YES and press OK key to enter setu p mode.
SETUP MODE ?
M
R
F
1
2
3
OK
←
4
5
6
0
7
8
9
·
→+ANTENNA +SATELLITE
+SYSTEM +INSTALLATION
Ant enna C ontrol Unit
2. Press OK key to en ter ANTENNA menu.
◀
+BLOCK ZONE →+DIAGONOSIS
Ant enna C ontrol Unit
3. Press arrow keys to move cursor to DIAGONOSIS an d press OK key to enter
DIAGON OSIS menu.
DIAGNOSIS FULL TEST
▲ FULL TEST ▼ ________________
Ant enna C ontrol Unit
4. Press UPand DOWN arrow keys to select a full diagnosis or single diagn osis an d
press OK key to execute the selected diagnosis.
DIAGNOSIS FULL TESTING
FULL TEST
Ant enna C ontrol Unit
5. A full diagnosis is completed.
●●●●●●●●●●●●●●●
M
R
F
M
▶
R
F
M
R
F
M
R
F
1
OK
4
7
1
OK
4
7
1
OK
4
7
1
OK
4
7
2
3
←
5
6
0
8
9
·
2
3
←
5
6
0
8
9
·
2
3
←
5
6
0
8
9
·
2
3
←
5
6
0
8
9
·
48
V110 – Marine Satellite Communication System
DIAGNOSIS COMMUNICATION
CODE 101 RESULT : PASSED
Antenna Control Unit
6. The diagn osis result is shown .
Diagnosi s Code :
CODE 101 : Th e data communication between th e antenna and the ACU is tested.
CODE 102 : Th e azimu th motor is tested.
CODE 103 : Th e elevation motor is tested.
CODE 104 : Th e cross-level motor is tested.
CODE 105 : Th e azimu th encoder is tested.
CODE 106 : Th e cross-level encoder is tested.
CODE 107 : Th e gyro sen sor is tested.
CODE 108 : Th e tilt sensor is tested.
CODE 109 : Th e sensor box motor is tested.
CODE 110 : The LNB is tested .
CODE 111 : The LNB skew motor is te sted.
CODE 112 : The sub-reflector is tested.
CODE 113 : The antenna power is tested.
CODE 114 : The AC U power is tested.
CODE 115 : The receiver power is tested.
Test Result : ●2●●●●●●●●●-●●-
● Test mean s passed.
– Test means skipped. (112 an d 115 will only be applied to Intellian TVRO an tenn a systems)
? Test means u nder process.
2 Refer to diagnosis code 102 as shown above f or occu rred error explanation .
M
R
F
1
2
3
OK
←
4
5
6
0
7
8
9
·
Operating the ACU
49
Satellite Settings
Load Satellite
→ YES NO
SETUP MODE ?
Ante nna Cont rol Unit
1. Press LEFT arrow key to move cu rsor to YES and press OK key to en ter setup
mode.
M
R
F
1
OK
4
7
2
3
←
5
6
0
8
9
·
+ANTENNA →+SATELLITE
+SYSTEM +INSTALLATION
Ante nna Cont rol Unit
2. Press RIGHT arrow key to move cursor to SATELLITE and press OK key to en ter
SATELLITE menu.
→+LOAD SAT. +EDIT SAT.
+ADD SAT.
Ante nna Cont rol Unit
3. Press OK key to enter LOAD SAT. menu.
LOAD SATELLITE
▲ [1] KOREA_5 113.00E ▼
Ante nna Cont rol Unit
4. Press UP and DOWN arrow keys to select satellite th at you wish to track.
Press OK key to load the selected satellite.
LOAD ?
→ YES NO
Ante nna Cont rol Unit
5. Press LEFT arrow key to move cu rsor to YES an d press OK key to load th e selected
satellite and execute the current settin gs. Or press RIGHT arrow key to move cursor to
NOan d press OK key to abort an d retu rn to the m ain di splay.
M
R
F
M
R
F
M
R
F
M
R
F
1
2
3
OK
OK
OK
OK
←
4
5
6
0
7
8
9
·
1
2
3
←
4
5
6
0
7
8
9
·
1
2
3
←
4
5
6
0
7
8
9
·
1
2
3
←
4
5
6
0
7
8
9
·
50
V110 – Marine Satellite Communication System
Edit Satellite Information
→ YES NO
SETUP MODE ?
Ant enna Cont rol Uni t
1. Press LEFTarrow key to move cursor to YES and press OK key to en ter setup
mode.
M
R
F
1
OK
4
7
2
3
←
5
6
0
8
9
·
+ANTENNA →+SATELLITE
+SYSTEM +INSTALLATION
Ant enna Cont rol Uni t
2. Press RIGHT arrow key to m ove cursor to SATELLITEand press OK key to enter
SATELLITE menu.
+LOAD SAT. →+EDIT SAT.
+ADD SAT.
Ant enna Cont rol Uni t
3. Press RIGHT arrow key and OK key to en ter EDIT SA T . menu.
▲ [1] KOREA_CS 113.00E ▼
4. Press UP and DOWN arrow keys to sel ect the satel lite th at you wh i sh to edi t and
press OK key to edit th e selected satellite.
LONGITUDE EDIT NAME
▲ 1
5. Edit th e satellite orbit position, LONGITUDE and NAME.
Press LEFTand RIGHT arrow keys u ntil the desired character is underscored
(selected). Press UP an d DOWN arrow keys to increase or decrease the value.
Or press NUMBERkeys to set the des ired valu e directl y. Press OK key to set th e
parameter.
EDIT SATELLITE
Ant enna Cont rol Uni t
13.00E ▼ KOREA_5
Ant enna Cont rol U nit
M
R
F
M
R
F
M
R
F
M
R
F
1
OK
OK
OK
OK
2
4
5
7
8
1
2
4
5
7
8
1
2
4
5
7
8
1
2
4
5
7
8
3
←
6
0
9
·
3
←
6
0
9
·
3
←
6
0
9
·
3
←
6
0
9
·
Operating the ACU
51
1
2
DVB VERIFY SKEW OFFSET
▲ DVB DECODE ▼ +0.0
Ante nna Cont rol Unit
6. Edit the satellite DVB VERIFY and SKEW OFFSET.
DVB VERIFY will be only activated and applied when choose to use DVB on trackin g
signal . Press UP and DOWN arrow keys to select DVB Verify 1) and press OK
key to set the parameter.
DVB Ve ri fy 1)
- AGC – use signal level for satellite trackin g.
- DVB Lock – use DVB Lock for satellite tracking.
- DVB Decode – u se DVB Decode for satellite tracking.
- DSS Decode – u se DSS Decode for satellite tracking.
SELECT LOCAL TRACKING SIGNAL
▲ 1
1300MHz ▼ NBD
Ante nna Cont rol Unit
7. Set th e LNB LOCAL frequency an d TRA CKING SI GNA L1).
Press LEFT and RIGHT arrow keys un til the desired character is un derscored
(selected). Press UP an d DOWN arrow keys to increase or decrease the value.
Or press NUMBER keys to set the desired value directly. Press OK key to set the
parameter.
Tracking Signal 1)
-NBD
-DVB
RX POL TX POL
▲ VERT. ▼ HORI.
Antenna Control Unit
8. Set th e RX POL and TX PO L
To select the pol arity f or both RX (receive ) an d TX (tran smit ) pol.
Press UP and DOWN arrow keys to select VERT ICALor HORIZONTAL . Press OK
key to set the parameter.
M
OK
R
F
3
4
5
6
7
8
9
1
2
4
5
7
8
1
4
7
←
0
·
3
←
6
0
9
·
2
3
←
5
6
0
8
9
·
52
V110 – Marine Satellite Communication System
DVB FREQ. SYMBOL NID
1747MHz ▼ 21300KHz 0x00AD
▲ 1
Antenna Control Unit
9. Set th e DVB FREQUENCY , SYMBO L RA TE and NID when choose to use DVB on
tracking sign al .
45,000 is th e m axim um allo wed symb ol rate val ue. N ID (n etwork ID) ran ge is fro m
0x000 to 0xFFFF (h exadecimal digit) .
Press LEFT and RIGHT arrow keys un til the desired character is underscored
(selected). Press UP and DOWN arrow keys to in crease or decrease th e value.
Or press NUMBERkeys to set th e desired val u e directly. Press OK key to set th e
parameter.
M
R
F
1
OK
2
4
5
7
8
3
←
6
0
9
·
NBD FREQ. BANDWIDTH
1070.000MHz ▼ 01.000MHz
▲ 0
Ant enna Cont rol Unit
10. S et th e NDB FREQ UENCY and BA NDWI DTH when choose to u se NDB on
tracking sign al .
NBD FREQUENCY is IF frequency.
Press LEFTand RIGHT arrow keys u ntil the desired character is underscored
(selected). Press UP and DOWN arrow keys to increase or decrease the valu e.
Or press NUMBERkeys to set the desired valu e directly. Press OK key to set the
parameter.
→ YES NO
Ant enna Cont rol Uni t
11. P ress LEFT arrow key to m ove cu rsor to YES and press OK key to save and
execute the current settings. Or press RIGHT arrow key to m ove cu rsor to NO
and press OK key to abort and retu rn to th e m ain di splay.
SAVE ?
M
R
F
M
R
F
1
OK
OK
2
4
5
7
8
1
2
4
5
7
8
Operating the ACU
3
←
6
0
9
·
3
←
6
0
9
·
53
Add Satellite Information
→ YES NO
SETUP MODE ?
Ant enna Cont rol U nit
1. Press LEFT arrow key to move cursor to YES and press OK key to enter setup
mode.
M
R
F
1
OK
4
7
2
3
←
5
6
0
8
9
·
+ANTENNA →+SATELLITE
+SYSTEM +INSTALLATION
Ant enna Cont rol U nit
2. Press RIGHT arrow key to move cu rsor to SATELLITE and press OK key to en ter
SATELLITE menu.
+LOAD SAT. +EDIT SAT.
→+ADD SAT.
Ant enna Cont rol U nit
3. Press DOWN arrow key and OK key to en ter ADD SAT. menu.
◀
→LONGITUDE EDIT NAME
116.00E KOREA_CS
Ant enna Cont rol U nit
4. Set the satellite LONGITUDE and satellite NAME.
Press LEFTand RIGHT arrow keys u ntil th e desired character is u nderscored
(selected). Press UP and DOWN arrow keys to in crease or decrease th e value.
Or press NUMBERkeys to set th e desired value directl y. Press OK key to set the
parameter.
DVB VERIFY SKEW OFFSET
▲ DVB DECODE ▼ +12.0
Ant enna Cont rol U nit
5. Edit the satellite DVB VERIFY and SKEW O F FSET.
M
R
F
M
R
F
M
▶
R
F
M
R
F
1
OK
OK
OK
OK
2
4
5
7
8
1
2
4
5
7
8
1
2
4
5
7
8
1
2
4
5
7
8
3
←
6
0
9
·
3
←
6
0
9
·
3
←
6
0
9
·
3
←
6
0
9
·
DVB VERIFY wi ll be only activated and applied wh en choose to use DVB on trackin g
sign al . Press UP and DOWN arrow keys to select DVB Verify 1) an d press OK
key to set the parameter.
DVB V eri f y 1)
- AGC – u se signal level for satellite tracking.
- DVB Lock – use DVB Lock for satellite tracking.
- DVB Decode – use DVB Decode for satellite tracking.
- DSS Decode – use DSS Decode for satellite tracking.
54
V110 – Marine Satellite Communication System
SELECT LOCAL TRACKING SIGNAL
0000MHz ▼ NBD
▲ 1
Ant enna C ontrol Unit
6. Set th e LNB LOCAL frequen cy and TRACKI NG S IG NA L1).
Press LEFT and RIGHT arrow keys until the desired character is u nderscored
(selected). Press UP and DOWN arrow keys to increase or decrease the valu e.
Or press NUMBERkeys to set the desired value directly. Press OK key to set the
parameter.
Tracki ng Signal 1)
-NBD
-DVB
RX POL TX POL
▲ VERT. ▼ HORI.
Ant enna Cont rol Unit
7. Se t th e RX POL and TX POL
To select th e polarity for both RX (rece ive ) and TX (tran sm i t ) pol.
Press UPan d DOWN arrow keys to select VERT ICALor HORIZONTAL . Press OK
key to set th e param eter.
M
R
F
M
R
F
1
OK
4
7
1
OK
4
7
2
3
←
5
6
0
8
9
·
2
3
←
5
6
0
8
9
·
DVB FREQ. SYMBOL NID
▲ 1
1747MHz ▼ 21300KHz 0x00AD
Antenna Control Unit
8. Set th e DVB FREQUENCY , SYMBO L RA TE and NID when choose to use DVB on
tracking sign al .
45,000 is th e m axim um allo wed symb ol rate val ue. N ID (n etwork ID) ran ge is fro m
0x000 to 0xFFFF (h exadecimal digit) .
Press LEFT and RIGHT arrow keys un til the desired character is underscored
(selected). Press UP and DOWN arrow keys to in crease or decrease th e value.
Or press NUMBERkeys to set th e desired val u e directly. Press OK key to set th e
parameter.
M
R
F
1
OK
2
4
5
7
8
Operating the ACU
3
←
6
0
9
·
55
NBD FREQ. BANDWIDTH
1070.000MHz ▼ 01.000MHz
▲ 0
Ant enna Cont rol Uni t
9. Set the NDB FREQ UENCY an d BA NDWI DTH wh en choose to use N DB on
tracking signal .
NBD FREQUENCY is IF frequency.
Press LEFT and RIGHT arrow keys until the desired character is un derscored
(selected). Press UP and DOWN arrow keys to in crease or decrease the value.
Or press NUMBER keys to set the desired valu e directly. Press OK key to set th e
parameter.
M
R
F
1
OK
2
4
5
7
8
3
←
6
0
9
·
→ YES NO
SAVE ?
Antenna Control Unit
10. Press LEFT arrow key to move cu rsor to YES and press OK key to save and
execute the cu rren t settin gs. Or press RIGHTarrow key to move cursor to NO
and press OK key to abort an d return to the main display.
M
OK
R
F
1
2
3
←
4
5
6
0
7
8
9
·
56
V110 – Marine Satellite Communication System
System Settings
Set LNB Local Frequency
→ YES NO
SETUP MODE ?
Antenna Control Unit
1. Press LEFTarrow key to move cursor to YES an d press OK key to enter
setup mode.
+ANTENNA +SATELLITE
→+SYSTEM +INSTALLATION
Antenna Control Unit
2. Press DOWN arrow key to move cursor to SYST EM and press OK key to en ter
SYSTEM menu.
M
R
F
M
R
F
1
OK
4
7
1
OK
4
7
2
3
←
5
6
0
8
9
·
2
3
←
5
6
0
8
9
·
◀
→+SET LOCAL +SET LOCATION
+MODEM PORT +BACKUP & RESTORE
Antenna Control Unit
3. Press OK key to enter SET LOCAL menu to set the LNB local frequency.
◀
→13V + 0KHz 18V + 0KHz
10000MHz 11300MHz
Antenna Control Unit
13V + 22KHz 18V + 22KHz
10750MHz ▲ 09750MHz ▼
Antenna Control Unit
4. Set th e LNB Local Frequency for each correspon ded voltage power .
(13V+0KHz, 18V+0KHz, 13V+22KHz, 18V+22KHz)
Press RET URN key and press LEFT and RIGHT arrow keys to select the parameter
you wi sh to edit. Press OK key to edit parameter. Or press RETURN key again to return
to the main display.
→ YES NO
Ant enna Cont rol U nit
5. Press LEFT arrow key to move cursor to YES and press OK key to save
cu rrent settin gs. Or move cursor to NO and press OK k ey to abort an d return to
the main display.
SAVE ?
M
▶
R
F
M
▶
R
F
M
R
F
M
R
F
1
2
3
OK
OK
OK
OK
←
4
5
6
0
7
8
9
·
1
2
3
←
4
5
6
0
7
8
9
·
1
2
3
←
4
5
6
0
7
8
9
·
1
2
3
←
4
5
6
0
7
8
9
·
Operating the ACU
57
Set Location
→ YES NO
SETUP MODE ?
Ant enna Cont rol Uni t
1. Press LEFT arrow key to move cu rsor to YES and press OK ke y to en ter setu p
mode.
M
R
F
1
OK
4
7
2
3
←
5
6
0
8
9
·
+ANTENNA +SATELLITE
→+SYSTEM +INSTALLATION
Ant enna Cont rol Uni t
2. Press DOWN arrow key to move cu rsor to SYST EM and press OK key to enter
SYSTEM menu.
◀
+SET LOCAL →+SET LOCATION
+MODEM PORT +BACKUP & RESTORE
Ant enna Cont rol Uni t
3. Press RIGHT arrow key to move cursor to SET LOCA TION and press OK key
to en ter SET LOCA TION menu.
◀
→ LATITUDE LONGITUDE
37.00N 126.50E
Ant enna Cont rol Uni t
4. Se t the cu rrent LATITUDE and LONGITUDE
Press LEFT and RIGHT arrow keys until the desired ch aracter is underscored
(selected). Press UPand DOWN arrow keys to increase or decrease the value.
Or press NUMBERkeys to set the desired valu e directly. Press th e OK key to set the
parameter.
M
R
F
M
▶
R
F
M
▶
R
F
1
OK
OK
OK
2
4
5
7
8
1
2
4
5
7
8
1
2
4
5
7
8
3
←
6
0
9
·
3
←
6
0
9
·
3
←
6
0
9
·
58
V110 – Marine Satellite Communication System
HEADING GYRO TYPE
▲ 0
00.0 ▼ NONE
Antenna Control Unit
5. Set th e ship’s HEADING and GYRO TYPE
Entry of ships heading i s not required when your system is conn ected to a
NMEA0813 or 1:1 Syn chro Headin g Gyro Com pass output. Determine th e type of gyro
com pass th at is use d on the s hip. En sure th at th e Gyro Type 1) is set correc tly.
Press LEFT and RIGHTarrow keys until the desired character is underscored
(selected). Press UPand DOWN arrow keys to increase /decrease the value.
Or press NUMBER keys to set the desired value directly. Press OK key to set the
parameter.
Gyro Type 1)
- None
-NMEA
- Synch ro 1:1
- Synch ro 36:1
- Synch ro 90:1
- Sychro 360:1
M
R
F
1
OK
4
7
2
3
←
5
6
0
8
9
·
→ YES NO
SAVE ?
Antenna Control Unit
6. Press LEFT arrow key to move cursor to YES and press OK key to save
current settings. Or move cu rsor to NOan d press OK key to abort and return to the
main display.
M
R
F
1
OK
2
4
5
7
8
Operating the ACU
3
←
6
0
9
·
59
Set Modem Port
→ YES NO
SETUP MODE ?
Antenna Control Unit
1. Press LEFTarrow key to move cursor to YES and press OK key to enter setup
mode.
M
R
F
1
OK
4
7
2
3
←
5
6
0
8
9
·
+ANTENNA +SATELLITE
→+SYSTEM +INSTALLATION
Ant enna Cont rol Uni t
2. Press DOWN arrow key to move cu rsor to SYST EM and press OK key to enter
SYSTEM menu.
◀
+SET LOCAL +SET LOCATION
→+MODEM PORT +BACKUP & RESTORE
Ant enna Cont rol Uni t
3. Press DOWN arrow keys to move cu rsor to COM. PORT and press OK key to
enter COM. PORT menu.
MODEM PORT PROTOCOL
▲ ETHERNET ▼ I/O CONSOLE
Ant enna Cont rol Uni t
4. Se t th e MOD EM PORT 1) and PROTOC OL 2)
To select a proper commun ication port and protocol on the ACU to interface with the
satellite modem. Press UPand DOWN arrow keys to select the correct parameter
and press OK key to set th e parameter.
Modem Port 1)
- ETHER N ET
-RS422
-RS232
Protoc ol 2)
- I/O Con sole
-Open AMIP
M
R
F
M
▶
R
F
M
R
F
1
OK
OK
OK
2
4
5
7
8
1
2
4
5
7
8
1
2
4
5
7
8
3
←
6
0
9
·
3
←
6
0
9
·
3
←
6
0
9
·
60
V110 – Marine Satellite Communication System
USE EXT. LOCK EXT. LOCK ACTIVE
▲ NO ▼ LOW
Ant enna Cont rol Unit
5. Set USE EXT. LOCK and EXT. LOCK ACTIVE (This menu will be activated when
choose PROTOCOL as I/O CONSOLE). The f unction of USE EXT. LOCK is to use
the external lock signal from the satellite modem. Con nect the cable from the
CON SOLE po rt on the rear of A CU to th e sate llite m odem if ch oose “Y ES” to use this
fu nc tion.
Ext. lock active is referred that modem lock ou tput from the modem provides a logic
in put via a v oltage to th e AC U to iden tify wh en it is on the correct sate llite . Thi s setti ng
can be varied from modem to modem. (Refer to the m odem manu al for details.)
Press UP and DOWN arrow keys to select the parameter options. Press OK key to set
the parameter. Press RETURN key to select th e parameter you wish to edit an d press
RETURN key again to save or abort and return to the main display.
M
R
F
1
2
OK
3
4
5
6
7
8
9
←
0
·
TX MUTE ACTIVE
▲ LOW ▼
Ant enna Cont rol Unit
6. Set TX MUTE ACTIVE (This menu will be activated when choose PROTOCOL as
I/O CONSOLE). A transmit inh ibit out put from th e ACU will disabl e/ mute the modem
transmit via a voltage whenever the antenna is blocked, searchin g, or is mis-poin ted 0.5
degrees from peak satellite position. This setting can be varied from modem to modem.
(Refer to the modem m anual for details.)
Press UP and DOWN arrow keys to select HIGH or LOW. Press OK key to set the
parameter. Press RETURN key to select the parameter you wish to edit and press
RETURN key again to save or abort and return to the m ain display.
SAVE ?
→ YES NO
Ant enna Cont rol Unit
7. Press LEFT arrow key to move cu rsor to YES an d press OK key to save
current settings. Or move cursor to NOan d press OK key to ab ort an d retu rn to the
main display.
M
R
F
M
R
F
1
2
OK
OK
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
Operating the ACU
←
0
·
←
0
·
61
System Backup & Restore
→ YES NO
SETUP MODE ?
Ant enna Cont rol Uni t
1. Press LEFT arrow key to move cu rsor to YES and press OK key to enter setup
mode.
M
OK
R
F
1
2
3
←
4
5
6
0
7
8
9
·
+ANTENNA +SATELLITE
→+SYSTEM +INSTALLATION
Ant enna Cont rol Uni t
2. Press DOWN arrow key to move cu rsor to SYSTEM and press OK key to en ter
SYSTEM menu.
◀
+SET LOCAL +SET LOCATION
+MODEM PORT → +BACKUP & RESTORE
Ant enna Cont rol Uni t
3. Press arrow keys to move cursor to BACKUP & RESTOREand press OK key to
enter BA CKUP & RESTORE menu.
▲ LOAD DEFAULT ▼
4. Press UP and DOWN arrow keys to select Default Process Type 1)
Press OK key to set the parameter and th e processing message will be displayed.
Defaul t Process Type 1 )
Loa d Defau lt : To restore the an tenn a back to factory def aul t settin gs.
Backu p User Data : To backu p the an tenn a setti ngs set by user.
Restore User Data : To restore the antenna by u sing the backup user data.
DEFAULT PROCESS TYPE
Ant enna Cont rol Uni t
LOAD DEFAUTL SETTING
Ant enna Cont rol Uni t
M
R
F
M
▶
R
F
M
R
F
M
R
F
1
OK
OK
OK
OK
2
4
5
7
8
1
2
4
5
7
8
1
2
4
5
7
8
1
2
4
5
7
8
3
←
6
0
9
·
3
←
6
0
9
·
3
←
6
0
9
·
3
←
6
0
9
·
62
V110 – Marine Satellite Communication System
Display Versions
→ YES NO
SETUP MODE ?
Ante nna Cont rol Unit
1. Press LEFT arrow key to move cursor to YES an d press OK key to en ter setu p
mode.
M
R
F
1
OK
4
7
2
3
←
5
6
0
8
9
·
+ANTENNA +SATELLITE
→+SYSTEM +INSTALLATION
Ante nna Cont rol Unit
2. Press DOWN arrow key to move cursor to SYSTEM and press OK key to en ter
SYSTEMmenu.
◀
→+VIEW VERSION
Ante nna Cont rol Unit
3. Press LEFT arrow key to move cursor to VIEW VERSI ON an d press OK key to enter
VIEW VERSIO N menu.
[VER.] ANT: 1.00 - 1.00 LIB: 1.00
4. System firmware and library versions are displayed. ANT: An tenn a, ACU: Antenna
Control Uni t, LIB: L ibrary . Press RETURN key to re turn to th e mai n di splay.
ANT : 1.0 0 (P CU) – 1.00 (STABILIZER)
ACU : 1.00 (ACU_MAIN) – 1.00 (ACU_MODEM) – 1.00 (ACU_GYRO)
ACU: 1.00 – 1.00 – 1.00
Ante nna Cont rol Unit
M
R
F
M
▶
R
F
M
R
F
1
2
OK
OK
OK
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
←
0
·
←
0
·
←
0
·
Operating the ACU
63
PC Controller Program
Introduction
GUI Software of Intellian v110 has been created for the user to easily set
up the antenna by using the user’s personal computer. Using the GUI
program enables the user to easily monitor and modify the information
of antenna, satellite and GPS. Additionally, detailed diagnostic methods
of the antenna are provided by the GUI program.
Figure 27. Screen Capture of Intellian Antenna PC Controller
To start this GUI program,
1. Connect one end of USB cable to the USB port on the computer.
2. Connect the other end of the USB cable (A-A or M-M Type) to the
“PC” connector in front of ACU. ( or Connect by using PC Serial Cable)
3. Execute GUI program by inserting the supplied CD-ROM into the CDROM drive of the computer.
64
V110 – Marine Satellite Communication System
Program Initialing and Communication Setup
Data communication between the antenna, ACU and satellite modem
must be established as the first step in order to start setting your
antenna.
Data Communication
Baud Rate Setting
Serial Port Selection
Serial Con nection
Con nect / Disconn ect
Modem Comm unication
(RS 232, RS422, Ethernet)
Status
Button
Type Selection
IP Address
Port Number
Connect/Disconnect
Network Button
Comm unication Type
Selection
TX Mute: A tran smi t inh ibit ou tput f rom th e ACU wil l
disable/mute the modem transmit .
EXT Lock: Modem lock ou tput from the modem
provides a l ogic inpu t to th e ACU to identify wh en it
is on th e correct satellite.
Figure 28. Communication Settings
Definition of Functions
Baud Rate Setting: To display the speed of data communication.
Connection Status: To display data connection between ACU and PC.
Serial Port Setting: To select serial port to be used.
Connect/ Disconnect: To establish connection between PC and ACU.
Modem: To setup the modem communication type. (RS232, RS422,
Ethernet)
Network Communication: To setup the IP address and port number.
Select Communication: To select communication type between Serial
Communication and Network Communication. You need to select “Serial
communication” when you connect your PC and the ACU by using the
supplied USB or serial cable. Select “Network Communication” when you
PC Controller Program
65
connect to the Internet or Intranet.
TX Mute: A transmit inhibit output from the ACU will disable/mute
the modem transmit via a voltage whenever the antenna is blocked,
searching, or is mis-pointed 0.5 degrees from peak satellite position.
This setting can be varied from modem to modem. (Refer to the modem
manual for details.)
EXT Lock: is referred that modem lock output from the modem
provides a logic input via a voltage to the ACU to identify when it is on
the correct satellite. This setting can be varied from modem to modem.
(Refer to the modem manual for details.)
Main Menu
Controller Menu
Mon itori ng Ante nna Cu rrent S tatu s
Display Sign al Level
(Tu ne r or N BD)
Display Modem an d
Antenna Statu s
Display ACU Model an d
Firm ware Versi on
Display Antenna Model and
Firm ware Versi on
Figure 29. Main Menu
Controller Menu
Position (GPS, Heading, Bow) & Manual Search
Set Tracking Information of Current Satellite
Tracking Information of Library
Version, Tracking Parameter & Block Zones
Diagnosis, Search Parameter & Sensor Adjust
66
V110 – Marine Satellite Communication System
Communication Information
Antenna Status
Search 2: The search range corresponds to the Search Pattern 2. Once
the signal is located, the antenna will enter to Search 3 mode
Search 3: The antenna is detecting the satellite signal which is above
current tracking level threshold. The search range corresponds to the
Search Pattern 3. Once the signal is located, the antenna will enter to
Tracking mode.
Tracking: Antenna is tracking the selected satellite.
Initialize: Antenna or the ACU is initializing.
Setup: Antenna is in setup mode.
Comm: Antenna is able to be communicated.
In the “Setup mode”, the “Back Up Position” or “Restore Position”
message will pop up if the “Backup” or “Restore” button is pressed.
The “Backup File (*.ibf)” will be generated on the PC if the “Back Up to
PC” button is pressed. In addition, you can also restore the settings by
using a saved “backup” file on the PC. These functions are only applied
to ACU 1.07 version or above.
Satellite Modem and Antenna Status
TX Enable: TX function is being enabled.
Enable Mode: Enable mode is activated.
Blockage: Antenna is facing the pre-defined block zones.
Pointing: Antenna is pointing to the target satellite.
Modem Lock: Satellite modem is sending a logic input to the ACU to
identify when the antenna tracks on the correct satellite.
LNB Rotate: LNB is rotating.
Other Information:
Local Freq: To display LNB local frequency.
PC Controller Program
67
Signal Level: To display signal level. It shows “Tuner” when choose
DVB tracking mode and “NBD” when choose NBD tracking mode.
Product Ant: To display antenna model and “PCU” firmware version.
Product ACU: To display ACU model and “Main” firmware version.
Definition of Program Command Buttons
Restart: To exit setup mode and restart antenna again.
Setup: To enter the setup mode.
Get Antenna Information: To indicate the information on display after
receiving input from the antenna.
Factory Setting: To initialize all antenna information to default as it
was in the factory status.
Save Satellite: If the current settings are able to locate the satellite (in
Tracking mode), press this button to save the settings. It will shorten
the satellite acquisition duration next time
Backup: To backup antenna information to ACU.
Restore: To restore the antenna by using saved information in ACU.
Controller Menu
Position (GPS, Heading, Bow) & Manual Search
Antenna makes use of GPS and ship’s heading information to search
satellite faster. The more precise the GPS information is, the quicker the
antenna is able to search for the satellite. The method to input
information into GPS is to mark “Edit GPS” first and push “Set GPS”
button after keying in the latitude and longitude information.
68
V110 – Marine Satellite Communication System
Figure 30. Antenna Angle, GPS and Ship’s
Bow offset is to offset the
angle difference between the
antenna’s bow an d
the sh ip’s bow.
Display cu rren t GP S and Shi p’s
heading. Put check m ark in f ront of
Edit GPS to edit GPS information
and press Set GPS bu tton
LNB skew in formation
To select the ship’s
heading device
Move antenn a azimuth and elevation
position an d LNB skew angl e
preciously by sm all of amou nt
assigned i n the text box.
The current antenna absolute AZ
and EL position and relative AZ
and LNB skew an gle. The absol ute azimuth
position of th e antenn a is the su m of ships
heading an d antenna relative .
Heading Information
Definition of Functions
Antenna Current GPS: To display current antenna GPS and Ship’s
heading information corresponding to the ship’s Gyro.
Heading Device: To select the ship’s heading device.
Antenna Angle 1: To display current antenna absolute AZ (azimuth)
and EL (elevation) position and relative AZ and LNB skew angle
Bow: To display current bow offset value.
Skew Information: To display current LNB skew angle.
Antenna Angle 2: To move antenna azimuth and elevation position
and LNB skew angle manually and preciously by small of amount
assigned in the text box.
Definition of Program Command Buttons
Set GPS: To set antenna GPS position manually.
Set Device: To select ship’s heading device
Set Bow Offset: To offset the angle difference between the antenna’s
bow and the ship’s bow.
Skew Calibration: To calibrate the LNB skew angle. Calibrate the LNB
PC Controller Program
69
skew angle when replace the control board, skew potentiometer or belt.
Set Tracking Information of Current Satellite
Sate llite nam e,
orbit position (lon gitu de)
and satellite skew offset
DVB Tracking Frequency
Display cu rren t LNB
local frequen cy and
supplied LNB power
NBD Tracking Frequency
Setup RX an d TX polarity
and trackin g method
LNB Local Frequency
Figure 31. Setup the Current Satellite Tracking Information
Definition of Functions
Satellite, Longitude and Skew Offset: To display current target
satellite name, longitude position and LNB skew angle offset value.
TR Frequency Common Info: 1) To display current LNB local
frequency and supplied LNB power. 2) To setup tracking method
between NBD and DVB (Tuner). 3) To setup RX and TX polarity.
DVB: To setup tracking information for DVB tracking mode.
NBD: To setup tracking information for NBD tracking mode.
Local Frequency: To display LNB local frequency to the corresponded
LNB power.
Base Local: To display the local frequency of NBD RX.
Select the Swedish Microwave (SMW) LNB type. If SMW LNB is
already set, SMW LNB type will be displayed.
In the “Setup mode”, check the “Edit Enable” check box to set the
desired value for each parameter you wish to edit. After the changes are
made, click “Edit Satellite Information” button to save the current
settings.
70
V110 – Marine Satellite Communication System
Definition of Program Command Buttons
Set Local Frequency: To setup LNB local frequency to the
corresponded LNB power.
Edit Satellite Information: To edit current satellite information.
Tracking Information of Library
Display th e saved satellite li st
from the ACU
Display Satellite Nam e, Lon gitude
and LNB Skew Offset
Setup LNB local frequen cy for th e
corresponded voltage power
DVB Sign al Tracking Mode :
Setup Frequ ency, Symbol
rate ,NID and Verify Type for the
satel lite th at yo u wi sh to track.
NBD Sign al Tracking Mode :
Setup Frequen cy and Ban dwidth
for the satellite th at you wi sh to
track.
Select polarity for RX and TX Pol and Tracking Mode
Figure 32. Library Information
Definition of Functions
Satellite, Longitude and Skew Offset: To display current target
satellite name, longitude position and LNB skew angle offset value.
Work Type: To select work type 1) Load Sat: To load the selected
satellite as target satellite 2) Edit Sat: To edit the selected satellite
3) Add Sat: To add the defined satellite into ACU.
TR Frequency Common Info: 1) To display current LNB local
frequency and supplied LNB power. 2) To setup tracking method
between NBD and DVB (Tuner). 3) To setup RX and TX polarity.
DVB: To setup tracking information for DVB tracking mode.
NBD: To setup tracking information for NBD tracking mode.
Local Frequency: To display LNB local frequency to the corresponded
LNB power.
PC Controller Program
71
Definition of Program Command Buttons
Get Data From ACU: To get the saved information from the ACU
during the “Setup mode”.
Edit Satellite: To change the satellite information of the selected
satellite.
Add Satellite: To add the satellite information as defined in the
current settings.
Open Library From PC: To open the library file from the supplied
Intellian CD.
Upload Library to ACU: To upload the library file to ACU.
Save Library to PC: To save the current library file to the PC.
Edit Library: To edit the selected library file.
Add Library: To add the library file as defined in the current settings.
Delete Library: To delete the selected library file.
It is required to press the “Save Library to PC” button after clicking “Edit
Library”, “Add Library “, or “Delete Library” button. These functions are
only applied to version 1.07 of the ACU firmware or above.
72
V110 – Marine Satellite Communication System
Version, Tracking Parameter & Block Zone
It is not recommended for a novice at satellite service to use this mode.
Consult Intellian for changing antenna parameters.
Setup DVB(Tuner)
detect and trackin g
thresh old
Setu p NBD
detect and trackin g
thresh old
Block Zone Setting
Produ ct Inf ormati on
Display an tenna and an tenna control un it firmware versions
and library version.
Figure 33. Display Antenna Versions and Tracking Parameters
Definition of Functions
Software Information: To display antenna and ACU firmware versions,
and library version.
Product Information: To display antenna and ACU serial numbers.
Parameter Setting (Tuner): To display current detect level threshold
and tracking level threshold when uses DVB (Tuner) tracking method.
Parameter Setting (NBD): To display current detect level threshold
and tracking level threshold when uses NDB tracking method.
Block Zones: To display current block zones by azimuth and elevation
sectors.
Definition of Program Command Buttons
Set Parameters: To setup the control parameters.
Set Block Zone: To setup the block zones by defining azimuth and
PC Controller Program
73
elevation sectors.
Diagnosis, Search Parameter & Sensor Adjust
Tilt Bi as Setti ng i s req uire d to set
when th e system is n ewly in stal led
or antenna control board is
replaced. When correcting the
“bubble”, it sh ould be as cl ose to the
center of th e fluid as possible.
EL Adjust – The elevation adjust
is to offset the an gle differen ce
between th e mechan ical elevation
angl e and actual elevation angle.
Setup Search Range
Anten na diagnosis test
Figure 34. Display Antenna Versions and Parameters
Definition of Functions
Tilt Sensor Bias: Tilt bias setting for EL (elevation) and CL (cross-level)
are required to set when the system is the control board, skew
potentiometer or belt is replaced. When correcting the “bubble”, it
should be as close to the center of the fluid as possible.
EL Adjust: The elevation adjustment is to offset the angle difference
between the mechanical elevation angle and actual elevation angle.
Diagnosis: To display the antenna diagnostic result.
Definition of Program Command Buttons
Ready: To confirm to the tilt bias setting. After pressing the Ready
button, a remote tilt calibration is required to align the sensor box
correctly by pressing button to adjust elevation and cross-level angle so
that 2-axis tilt sensor will be aligned accurately to the axis it related to.
The fluid filled tilt sensor provides a two dimensional horizon
74
V110 – Marine Satellite Communication System
reference. The system is not able to be automatically calculated the
exact center value, therefore, it is necessary to perform this procedure to
manually enter any offset required to make sure the PCU receives a true
reference to the horizon.
Diagnosis: If “Diagnosis” button is pressed, the system will carry out
the selected full diagnosis “Test All” or single diagnosis. The software will
display the diagnosis results (Blue dot represents “normal”, red
represents “abnormal” and green represents “the diagnosis is under
process”).
Set EL Adjust: To offset the angle difference between the mechanical
elevation angle and actual elevation angle.
Calibration Gyro: Calibrate the bias of gyro sensor located on the
sensor box. Before calibrating the gyro sensor, make sure that the
antenna is placed on a rigid and flat platform. During the calibration
process, the antenna should avoid any motion as it can affect the
antenna’s performance. After clicking the “Calibration Gyro” button, the
green dot will be displayed as a ready signal to calibrate the gyro sensor.
The red dot (fail) or blue dot (pass) will be displayed once the calibration
is completed,
Idle Mode: To release the EL/CL BLCD motor brakes during the
“Setup mode”. The antenna can be moved manually during the idle
mode. It is required to turn off and turn on the ACU power to bring the
antenna out of the idle mode.
PC Controller Program
75
Warranty
This product is guaranteed by Intellian Technologies Inc., against defect
due to faulty workmanship or materials and this guarantee covers for 1
year’s parts from installation or 18 months from shipment.
You are requested to present a copy of the purchase receipt issued by
Intellian Technologies, Inc. that presents the date of purchase for after
sales service under warranty. In case of failure to present the date of
purchase, the warranty period is to be calculated to 30 days after the
manufacturing production date.
If you discover a defect, Intellian Technologies, Inc. will, at its option,
repair, replace or refund the purchase price of the product at no charge
to you, provided you return it during the warranty period, transportation
charges prepaid, to the factory direct. Please attach your name, address,
telephone number, a description of the problem and a copy of the bill of
sale or sales receipt as proof of date of original retail purchase, to each
product returned to warranty service. Alternatively, you may bring the
product to an Authorized Intellian Technologies, Inc. dealer/distributor
for repair.
This Limited Warranty does not apply if the product has been damaged
by accident, abuse, misuse or misapplication or has been modified
without the written permission of Intellian Technologies, Inc.; if any
Intellian Technologies, Inc. serial number has been removed or defaced;
or if any factory-sealed part of the system has been opened without
authorization.
76
V110 – Marine Satellite Communication System
Appendix : v110 Technical Specification
General
Approvals
CE – conforms to
FCC – verified to
Dimensions
Satellite antenna unit
Antenna dish diameter
Antenna control unit
Weight
Satellite antenna unit
Antenna control unit
Antenna system performance
Tx Frequency 14.0 ~ 14.5 GHz Ku-band
Tx Gain 41.3 dBi @ Mid band
Rx Frequency 10.95 ~ 12.75 GHz Ku-band
Rx Gain 40.2 dBi @ Mid band
Polarized Feed Cross-pol or Co-pol
Skew Control Automatic Skew-angle Control
Azimuth range Unlimited
Elevation range -15° ~ +120°
Cross-level range +/- 37°
Stabilization Accuracy
Max Ship’s motion
Turning rate Up to 12°/ sec & 5°/ sec2
BUC 4W, 6W, 8W (optional)
Rack Mount Antenna Control Unit
Display 2 Line 40 Character Graphic VFD Module
Serial Interface 19200bps 8, N, 1, RS-232C
Modem Interface
EU Directive 89/336/EEC
CFR47:Part 15
146.8 cm x 151.7 cm (57.8” x 59.7”)
105cm (41.3")
43cm x38cm x4.37cm (16.9”x14.9”x1.7”)
150kg (330 lbs)
5.2kg (11.5 lbs)
0.2° peak mis-pointing @ max ship
motion condition
+/-25°roll, +/- 15° pitch, +/-8° yaw @ 6
sec
Ethernet port / RS-232C / I/O ports
Appendix
77 Appendix
Remote Access TCP / IP
Input Power
90~ 260V AC, 47~ 63Hz
(Max 300W including 8W BUC Power)
Gyrocompass Interface NMEA/ Synchro/ Step-by-Step
78
V110 – Marine Satellite Communication System
Intellian Technologies, Inc.
HQ
Dongik Building 2
98 Nonhyun-Dong, Gangnam-gu,
Seoul 135-010, Korea
Tel : +82-2-511-2244
Fax: +82-2-511-2235
Factory
SK Ventium 104-501,
522 Dangjeong-Dong, Gunpo-Si,
Kyunggi-Do 435-776, Korea
Phone: +82-31-436-1488
Fax: +82-31-436-1489
R&D Center
SK Ventium 104-601,
522 Dangjeong-Dong, Gunpo-Si,
Kyunggi-Do 435-776, Korea
Phone: +82-31-436-2280
Fax: +82-31-436-2284
Intellian Technologies USA, Inc.
9261 Irvine Blvd.
Irvine, CA 92618 USA
Phone: +1-949-916-4411
Fax: +1-949-271-4183
nd
Flr.,
customersupport@Intelliantech.com
www.Intelliantech.com
Appendix
79 Appendix
Loading...