Intelix VGA2-SW4 User Manual

VGA2-SW4 Installation Guide

Troubleshooting

Symptom

Possible Solutions

No signal

Check VGA and audio cables for damage. Make
sure cables are of good quality and in good
condition.

Verify source and destination VGA ports are
operational.

Poor image and/or sound

Check VGA and audio cable quality.

Use shorter cables.

Unusual colors in the video

Verify VGA connectors are in good condition,
with no bent or missing pins.

Instructions

1. Turn off power to sources and destination

device according to the manufacturer’s
instructions.

2. Connect the video outputs of the source

devices to the VGA2-SW4 VGA inputs with
high quality HD15 cables.

3. Connect the audio outputs of the source

devices to the VGA2-SW4 audio inputs with

3.5mm cables.

4. Connect the video input of the destination

device to the video output of the VGA2-SW4
with high quality HD15 cables.

5. If the VGA2-SW4 will be controlled by a third-

party control system, connect a DE9 cable to
the RS232 port

6. Connect the included power supply to the

5VDC connector.

7. Power on connected sources and destination

device.

Important notice:

 Do not attempt to disassemble or alter the

switcher housing. There are no user-serviceable
parts inside the unit. Doing so will void your
warranty.

 To minimize the possibility of equipment damage

from electrostatic discharge (ESD), all source and
destination equipment must be powered off during
installation.

 Allow proper ventilation to reduce the risk of

thermal failure.

RS232 Transmission Format:

Baud Rate: 9600 bps
Data Bit: 8 bits
Parity: None
Stop Bit: 1 bit

ALL RS232 COMMANDS MUST CONCLUDE
WITH A CARRIAGE RETURN AND LINE FEED.

Command Code

Comment

“I” + “1”

Port 1 On

“I” + “2”

Port 2 On

“I” + “3”

Port 3 On

“I” + “4”

Port 4 On

“P” + “1”

Power On

“P” + “0”

Power Off

VGA2-SW4 Installation Guide

The Intelix VGA2-SW4 is a four input, one output RGB/YPbPr and stereo audio switcher. The VGA2-SW4 supports VGA, SVGA,

XGA, SXGA, UXGA (1600x1200), WUXGA (1920x1200), 480i, 576i, 480p, 576p, 720p, 1080i, and 1080p.

8001 Terrace Ave. Phone: [phone]
Suite 201 Toll-Free: 866-462-8649
Middleton, WI 53562 Fax: [phone]

VGA2-SW4 Installation Guide

Technical Specifications

I/O Connections

Input Connectors

4x VGA (female), 4x 3.5mm stereo audio inputs

Video Bandwidth

300 Mhz

Video Impedance

75 ohm

Video Level

Unity, Nominal 1V p-p

Audio Bandwidth

20Hz to 20kHz

Audio Impedance

20K ohm

Audio Level

Unity, Nominal

Television Standards

NTSC, PAL, HDTV

Supported Resolutions

PC: VGA (640x480), SVGA (800x600), XGA(1024x768), SXGA
(1280x1024), UXGA (1600x1200), WUXGA (1920x1200)
HDTV: 480i, 576i, 480p, 576p, 720p, 1080i, 1080p
All resolutions @ 60 Hz

Control

Front Panel, RS232

Chassis and Environmental

Dimensions (HxWxD)

1.87"x11.5"x7" (48x292x176mm)

Shipping Weight

5.15 lbs. (2.34 kg)

Operating Temperature

+32° to +122° F (0° to +50° C)

Operating Humidity

10% to 90%, Non-condensing

Storage Temperature

+14° to +140° F (-10° to +60° C)

Storage Humidity

10% to 90%, Non-condensing

Enclosure

Painted Steel

External Power Supply

5VDC @ 2.6A

Regulatory

CE, RoHS

Other

Warranty

2 years

What’s in the Box

VGA2-SW4 (1 ea), IR Remote (1 ea.), AC Power Supply (1 ea.),
Installation Guide (1 ea.)

8001 Terrace Ave. Phone: [phone]
Suite 201 Toll-Free: 866-462-8649
Middleton, WI 53562 Fax: [phone]