Page 1
Specifications
Specifications subject to change without notice.
Maximum Distance* 350 feet
Bandwidth DC to 1 MHz
Power No power required
Signals Transmitted Mouse data, mouse clock, keyboard data, keyboard clock, VCC,
ground
Unshielded Twisted Pair Maximum capacitance: 20 pf/foot
Cabling Specifications Impedance: 100 ohms @ 1 MHz
(24 gauge or lower solid Attenuation: 6.6 dB/1000 ft. @ 1 MHz
copper) Cat 5, Cat 5e, Cat 6, Cat 7 compatible
Connectors Send balun: Two (2) female 6-pin mini DIN to one (1) RJ45
Receive balun: Two (2) male 6-pin mini DIN to one (1) RJ45
Color Code Purple: Keyboard
Green: Mouse
RJ45 Pinout Keyboard: 7 & 8, pair 4
4 & 5, pair 1
Mouse: 1 & 2, pair 2
3 & 6, pair 3
Temperature Operating: 32 to 131 F (0 to 55 C)
Storage: -4 to 185 F (-20 to 85 C)
Humidity: up to 95% non-condensing
Enclosure ABS fire retardant black plastic
Dimensions Send balun: 2.4” x 2.3” x 1.0”
Receive balun: 2.0” x 1.0” x 1.0” with two 7.5” lead cables
Weight 1.6 oz (45 grams)
Ordering Information PS2, includes both send and receive baluns
Regulatory FCC, CE (pending)
Warranty 2 years
* Distances and picture quality may be affected by cable grade, cable quality, source and destination
equipment, RF and electrical interference, and cable patches. Intelix specifications are based on
straight-through cabling with standard-grade Cat 5.
Contact Information
Intelix
2222 Pleasant View Road
Middleton, WI 53562
Toll-free: 866-4-MATMIX
Phone: 608-831-0880
Fax: 608-831-1833
www.intelix.com
AV overCat5.com
Intelix PS/2 Keyboard and Mouse Extender
InsIns
InsIns
Ins
tt
tt
t
allation Manualallation Manual
allation Manualallation Manual
allation Manual
The Intelix PS2 balun extends a computer’s
PS/2 keyboard and mouse up to 350 feet
over structured cabling, such as Cat 5.
Typical applications include classroom and
educational facilities, corporate and boardroom audio-visual systems, digital signage,
collaborative PC systems, and bio-medical
information systems.
The Intelix PS2 contains both a send and receive balun. Both models are completely passive
and do not require a power supply.
To install the PS2 baluns, perform the following steps:
1. Turn off power and disconnect the computer and any other connecting equipement
by following the manufacturer’s instructions.
2. Connect the source keyboard to the purple connector on the send PS2 balun, then
connect the source mouse to the green connector on the send PS2 balun.
3. Connect the receive PS2 to the computer or destination equipment by connecting the
purple connector into the computer’s keyboard port and the green connector into the
computer’s mouse port.
4. Choose the structured cabling to be used. Verify the desired structured cabling is not
being used for other LAN or telephony equipment.
5. Complete the connection between the send and receive PS2 baluns using structured
cabling, such as Cat 5. Ensure the RJ45 connector pinout conforms to EIA/TIA 568
A or B crimp patterns.
6. Power on the computer or related equipment and test for correct operation.
Installation
Caution: Do not attempt to open the balun housing. There are no user-serviceable parts
inside the PS2. Opening the unit will void your warranty.
Caution: Do not connect the PS2 to a telecommunication outlet wired to unrelated
equipment. Making such a connection may damage the equipment and/or
balun. Please ensure all wiring is “straight-through.”
Caution: Do not mount the balun over equipment ventilation openings. Covering the
openings may cause the equipment to overheat.
Page 2
Troubleshooting
If your equipment malfunctions with PS2 baluns in place, follow the troubleshooting procedures below:
1. Perform diagnostics on your computer equipment by following the manufacturer’s
instructions.
2. Check all the connections and the structured cabling system. Verify the RJ45 crimp
pattern conforms to either EIA/TIA 568A or 568B standards.
3. Check the pin configuration of the structured cabling.
4. The maximum operational distances over which the PS2 can be transmitted is
dependant on the equipment used and cable. Ensure that the maximum
recommended operational distances have not been exceeded.
5. Check that only twisted pair patch cords are being used.
6. Verify the connectors are properly matched; i.e., keyboard to keyboard and mouse to
mouse.
7. Connect the devices per the recommended procedure and then reboot the computer.
8. Replace the PS2 balun with another PS2 that is known to be working.
9. If you still cannot diagnose the problem, contact Intelix for support.
Frequently Asked Questions
How do I expose the individual pairs in Cat 5 cabling?
There is no single method when exposing the four
individual pairs in twisted pair cabling, such as Cat 5
and Cat 6; however, it does help to have a cable
stripping tool designed to strip the cable jacket/
insulation.
Begin by stripping back the cable’s outer jacket/
insulation about an inch (or more depending on
whether multiple baluns will be connected to the pairs
of a single cable) so that the internal wires are exposed.
Be careful not to cut the internal wires when stripping
the insulation/jacket. Eight twisted wires and a string
should now be visible; the string is unnecessary and
may be removed. These eight wires, which when
combined form four pairs, connect directly to the
baluns. Typical protocol pairs similar colors; the
important thing is to verify the same color-coded pairs
are used on each end.
How do I crimp an unshielded RJ45 connector onto Cat 5?
Crimping an RJ45 connector onto Cat 5 is a fairly straight forward task, assuming you have
the proper tools. Keep in mind that baluns require either the EIA/TIA 568A or 568B crimp
pattern, which are the industry standards for networking.
1. First, strip a portion of the insulation about 3/4" to expose the four twisted pairs.
2. Next, untwist the wires and fan them out so that they match either EIA/TIA 568A or
568B pattern.
3. Evenly trim the wires to about 1/2". Most RJ45 crimp tools feature a built-in wire
trimmer.
4. Insert the trimmed wires into the RJ45 connector so that each wire is in its individual
slot. Verify each wire is completely inserted.
5. Finally, insert the RJ45 connector into the crimp tool and squeeze firmly.
6. Repeat the above steps on the other end of the Cat 5 cable and verify pinout is identical on each end.
Loading...