Intelix INT-PS82-H2 Quick Start Guide

INT-PS82-H2 Quick Install Guide

This guide is for quick installa on only.

For complete owners manual go to www.libav.com or use a QR reader to access the

manual via QR code below.

Rev 181210

Scan QR Code with your Smart-phone or Tablet

11675 Ridgeline Drive

Colorado Springs, CO

80921

Phone: [phone]

Toll-Free: 800-530-8998

Fax: [phone]

INT-PS82-H2 Quick Guide

Product Overview

The INT-PS82-H2 is an 8x2 mul-format seamless presentaon matrix switcher featuring four
HDMI, one HDBaseT, one USB-C , one DisplayPort and one VGA input as well as an HDBaseT and
two HDMI outputs, one of which is a mirrored from the HDBaseT output. The switcher supports
automac switching based on video sensing, and each output can be congured separately for auto
or manual switching. The INT-PS82-H2 provides true 4K up/down scaling up to 4K@60Hz / 4:4:4 /
8 bit deep color and both outputs can be scaled to dierent resoluons independently. The INT­PS82-H2 provides external audio inputs that can be embedded in HDBaseT, HDMI and VGA video
inputs respecvely. Moreover, it provides an global, auxiliary MIX audio input that can be assigned
to any output. The switcher can de-embed digital and/or analog audio from both outputs for audio
reinforcement purposes.

The INT-PS82-H2 ships with an 18G HDMI 2.0 HDBaseT receiver capable of extending 4K signals up to
40m / 132’ or 1080p up to 70m / 232’. The INT-PS82-H2 can also tunnel RS232 and bi-direconal IR sig­nals to and from the HDBAseT receiver. The extension system enables high data rates by ulizing visual
lossless compression at a 2:1 data compression rate when the signal surpasses 10Gbps, anything under
10Gbps will never be compressed. Supports stac HDR (HDR10) only when data rate exceeds 18Gbps,
supports dynamic HDR (HDR10+ / Dolby Vision) when data rate is 10Gbps or less.

The switchers funcons can be controlled by built in web server / GUI, IR remote, RS232, IP or by
front panel buon operaon. Two relay switches are built in for projector or shades control. For a
list of available control commands for RS232 and IP control, please see the owners manual for this
product located online at www.libav.com.

Package Contents

• INT-PS82-H2 8x2 HDMI 2.0 Switcher

• 70m HDBaseT 2.0 Receiver

• Quick Install Guide

• (3) 3-pin Phoenix connectors

• (7) 5-pin Phoenix connectors

• (1) 3.5mm Audio Cable (for IR cascading)

• IR Remote

• (1) IR Emier

• (1) IR Receivers

• (1) DC24V 6A power supply with US power plug

• (2) Rack mount ears with 6 mounng screws

• (4) Plasc Cushions

2

INT-PS82-H2 Quick Guide

Front Panel View - Switcher

1 2 3 4 5

1. POWER LED - Illuminates solid RED when switcher is in standby mode or illuminates GREEN when

device is powered ON.

2. SOURCE

• 1- HDBT - HDBaseT input selec on / Le� key for On Screen Display (OSD)

• 2- HDMI - HDMI input selec on / Right key for On Screen Display (OSD)

• 3- HDMI - HDMI input selec on / Up key for On Screen Display (OSD)

• 4- HDMI - HDMI input selec on / Down key for On Screen Display (OSD)

• 5- HDMI - HDMI input selec on

• 6- VGA - VGA input selec on

• 7- DP - DisplayPort input selec on

• 8- USB C - USB-C input selec on / Enter key for On Screen Display (OSD)

• AUTO - Auto switch selector. Press this to enter / exit auto switch mode. Press and hold for 2 seconds

to enable OSD menu

3. OUTPUTS

• 1- HDMI - HDMI output selector

• 2- HDBT - HDBaseT output selector

Note: To make a video route, select the desired SOURCE bu on, then select the desired OUTPUT bu on.
The video will switch in 2 to 3 seconds. For faster switch response, select the desired SOURCE bu on,
then select the desired OUTPUT bu on and then press the selected SOURCE bu on again.

4. RESOLUTION - Two output video resolu ons selectors. Press 1.HDMI or 2.HDBT bu on repeatedly to

cycle through the available video resolu ons.

5. VOLUME - Variable audio control

• Press the volume knob to toggle among MIX, HDMI OUT and HDBT OUT audio control.

• Rotate the knob to increase decrease volume of the selected audio

• Press and hold the knob at least 3 seconds to mute selected audio, rotate the knob to unmute

3

INT-PS82-H2 Quick Guide

Back Panel View - Switcher

3 4

1 2

1. INPUT

• 1- HDBT - RJ45 / HDBaseT Input, external 5 pin phoenix for balanced audio input

• 2- HDMI - HDMI input, external 5 pin phoenix for balanced audio input

• 3- HDMI - HDMI input, external 5 pin phoenix for balanced audio input

• 4- HDMI - HDMI input

• 5- HDMI - HDMI input

• 6- VGA - VGA with 3.5mm audio input

• 7- DP - DisplayPort input

• 8- USB C - USB-C input - supports ALT-DP

• IR - 3.5mm IR input to connect IR receiver for IR pass through

• MIX - 5 pin phoenix for global balanced audio input

2. OUTPUTS

• 1- HDMI - HDMI output

• 2- HDMI - HDMI output (mirrors HDBT output)

• 2- HDBT - HDBaseT output

• IR IN - 3.5mm IR input to connect IR receiver for IR pass through

• IR OUT - 3.5mm IR input to connect IR emi er for IR pass through

3. AUDIO OUTPUT

5

• 1 - 5 pin phoenix for balanced analog audio input and one digital SPDIF audio output for 1-HDMI
output audio de-embedding

• 2 - 5 pin phoenix for balanced analog audio input and one digital SPDIF audio output for 2-HDBT
output audio de-embedding

4. CONTROL

• RS232 - 3 pin phoenix connector for RS232 control

• RELAY 1-2 - (2) 3 pin phoenix connectors for relay control

• IR EYE - 3.5mm IR input to connect IR receiver for local switcher control

• TCP/IP - RJ45 to control device via network / web GUI

• FIRMWARE - Type A USB port for  rmware upgrade

5. DC24V- Locking power supply port

4

INT-PS82-H2 Quick Guide

Front Panel View - HDBaseT Receiver

1 2

1. MODE SWITCH

• CTRL - When placed in control mode, HDBaseT receiver will receiver RS232 pass through commands

from the switcher

• UPDATE B - Update mode for system program

• UPDATE A - Update mode for Valens program

2. POWER LED - Illuminates solid RED when power is applied

5

INT-PS82-H2 Quick Guide

Back Panel View - HDBaseT Receiver

1 2 3 4 5

1. DC12V- Locking power supply port

2. HDBT IN - RJ45 HDBaseT connec on. Connect Cat6 cable to HDBT output transmi er of the INT-

PS82-H2

3. IR IN / IR OUT

• 3.5mm IR input port for connec on to IR receiver or IR system

• 3.5mm IR output port for connec on to IR emi� er

4. RS232 - 3 pin Phoenix connector port for connec ng / passing RS232 control from INT-PS82-h2

5. HDMI OUT - HDMI output port for connec on to video display

6

INT-PS82-H2 Quick Guide

Connecvity Instrucons

1. Verify all components included with the INT-PS82-H2 set are present before installaon.

2. If the INT-PS82-H2 is going to be permanently mounted in a rackmount case, aach the included
mounng brackets with the supplied screws.

3. Turn o power and disconnect the audio/video equipment by following the manufacturer’s
instrucons.

4. Connect Category 6 or greater twisted pair cable with RJ45 connectors between the INT-PS82-H2
HDBaseT output / transmier to the supplied receiver and HDBaseT input / receiver to a compable
Intelix HDBaseT transmier. TIA/EIA-568B straight-through wiring connecons must be used.

5. Connect an HDMI cable that is less to or equal to 5 meters in length between the display and the
HDMI output of the INT-PS82-H2 HDBaseT receiver.

6. Connect an HDMI cable that is less to or equal to 5 meters in length between the display and the
HDMI output of the INT-PS82-H2. For display devices that are further away, an HDMI extension device
will be required to complete the connecon.

7. Connect a source device to the HDBaseT transmier input using a HDMI cable that is less than or
equal to 5 meters in length.

8. Connect a source device to the HDMI inputs using a HDMI cable that is less than or equal to 5
meters in length. For source devices that are further away, an HDMI extension device will be required
to complete the connecon.

9. Connect a source device to the DisplayPort input using a DisplayPort cable that is less than or equal
to 5 meters in length. For source devices that are further away, an extension device will be required to
complete the connecon.

10. Connect a source device to the USB-C input using a USB-C video cable that is less than or equal to
2 meters in total length.

11. Connect a VGA source device to the VGA input using a 15-pin VGA cable.

12. Connect a 3.5mm audio cable into the respecve VGA audio input

13. Connect RS232 control between the display to control connected display or connect to a 3rd party
control system to control switcher funcons (oponal)

14. Connect TCP/IP control to a 3rd party control system to control switcher funcons (oponal)

NOTE: A list of control commands for this unit is available in the owners manual online at
www.libav.com under the DOCUMENTATION tab of the INT-PS82-H2 product page

15. Connect IR receiver to IR EYE port to control switcher via supplied IR remote (oponal)

16. Connect the included power supply to the INT-PS82-H2 and lock the power supply to the power
connector by twisng the locking collar clockwise.

17. Power on aached audio/video devices.

7

INT-PS82-H2 Quick Guide

Cabling Wiring Requirements

HDBaseT Cabling

To ensure proper performance of the INT-PS82-H2, it is recommended that you use solid
core, shielded Category 6 F/UTP cabling at a minimum. Category 5e F/UTP may perform
well but may not support power over HDBaseT reliably over longer distances.

When using shielded category cabling ALWAY S ...

....use shielded connectors

....properly ground the category cable

For op mized HDBaseT performance use the following Liberty Wire and Cable branded
cabling;

Category 6 plenum; 24-4P-P-L6SH
Category 6A plenum; 24-4P-P-L6ASH

Category 6 NON-plenum; 24-4P-L6SH
Category 6A NON -plenum; 24-4P-L6ASH

Twisted Pair Wiring

Use TIA/EIA-568B wiring for Category 6
connec on between send and receive
units.

RS232 Wiring

Some controllers may not have a DB9 port available
for RS232 communica on, but may have removable
terminal block connec ons. Consult the manual
of the control device(s) to determine which pins
the TX/RX signals are carried on. Be sure to always
connect TX to RX and RX to TX.

TX G RX

RS232 PORT

Connected RS232
Device Pins

RX G TX

8

INT-PS82-H2 Quick Guide

Technical Specicaons - Switcher

Video

Video Inputs (1) HDBaseT, (4) HDMI, (1) DisplayPort, (1) VGA, (1) USB-C
Video Input Connectors (1) RJ45 (HDBaseT), (4) HDMI Type A Female, (1) USB-C , (1) DisplayPort, (1) 15-pin VGA
Input video Signal HDMI for HDMI input, ALT-DP Mode for USB-C 3.0, DP Version 1.2 for

DisplayPort input
HDBaseT Input Resoluon Support Up to 4Kx2K@60Hz 4:2:0 / 8 bit deep color (10.2Gbps)
HDMI Input Resoluon Support Up to 4Kx2K@60Hz 4:4:4 / 8 bit deep color
USB C Input Resoluon Support Up to 4Kx2K@30Hz 4:4:4 / 8 bit deep color
DisplayPort Input Resoluon Support Up to 4Kx2K@60Hz 4:4:4 / 8 bit deep color
VGA Input Resoluon Support Up to 1920x1200 (50/60Hz)
Video Output (2) HDMI, (1) HDBaseT
Video Output Connector (2) Type-A Female HDMI, (1) RJ45
Output Resoluon Support Up to 3840 x 2160 @60Hz / 4:4:4 / 8 bit deep color

Standards HDMI 2.0, HDCP 2.2 and CEC
Bandwidth HDBaseT Input (Receiver): 10.2Gbps

All other inputs / outputs: 18Gbps

24V DC Power One (1) Locking Barrel (5.5 mm OD, 2.1 mm ID)

Audio Input

Audio Input (1) External balanced audio (L+R) for 1-HDBT input port

(1) External balanced audio (L+R) for 2-HDMI input port

(1) External balanced audio (L+R) for 3-HDMI input port

(1) Stereo auxiliary audio for 6-VGA input port

(1) Balanced MIX audio
Audio Input Connector (4) 5-pin terminal blocks (1) 3.5mm jack
Frequency Response 20Hz – 20KHz, ±3dB
Max Input Level 2.0Vrms ± 0.5dB. 2V = 16dB headroom above - 10dBV (316mV) nominal consumer line

level signal.
Input Impedance >10KΩ

Audio Output

Audio Output (1) Balanced audio (L+R) for 1-HDMI output audio de-embedding

(1) Digital SPDIF audio (L+R) for 1-HDMI output audio de-embedding

(1) Balanced audio (L+R) for 2-HDBT output audio de-embedding

(1) Digital SPDIF audio (L+R) for 2-HDBT output audio de-embedding
Audio Output Connector (2) 5-pin terminal blocks (2) Toslink connectors
Frequency Response 20Hz – 20KHz, ±3dB
Max Input Level 2.0Vrms ± 0.5dB. 2V = 16dB headroom above -10dBV (316mV) nominal consumer line

level signal
Output Impedance 70Ω

9

INT-PS82-H2 Quick Guide

Technical Specicaons - Switcher

Control

Control Ports (1) RS232, (2) Relay 1-2, (1) IR Eye, (2) IR IN, (1) IR OUT, (1) TCP/IP, (1) Firmware
Control Connectors (3) 3-pin terminal blocks, (4) 3.5mm jacks, (1) RJ45, (1) Type-A USB
IR Carrier Frequency Range 33-55kHz at 5 volts

HDBaseT Signal Characteriscs

Maximum Distance HDBaseT Input (Receiver): 70 m (up to 1080p) , 40 m (up to 4K@60Hz / 4:2:0 / 8 bit

deep color)
HDBaseT Output (Transmier): 70 m (up to 1080p) , 40 m (up to 4K@60Hz / 4:4:4 / 8

bit deep color)
Cable Requirements Solid core shielded Category 6 F/UTP cable or greater with TIA/EIA-568B crimp paern
Bandwidth HDBaseT Input (Receiver): 10.2Gbps

HDBaseT Output (Transmier): 18Gbps

Chassis and Environmental

Dimensions (WxHxD) 436 mm x 44 mm x 356.5 mm (17 in x 1.7 in x 14 in) – 1RU
Shipping Weight 2.87kg (6.3 lbs.)
Operang Temperature 0° to +55° C (+32° to +131° F)
Operang Humidity 10% to 90%, Non-condensing
Storage Temperature -20° to +70° C (+14° to +158° F)
Storage Humidity 10% to 90%, Non-condensing

Power, ESD, and Regulatory

Power Supply Input 100V-240VAC / 50-60 Hz
Power Supply Output 24VDC / 6A
Power Consumpon 85 was (max)
ESD Protecon 15kV
Product Regulatory FCC, CE, RoHS
Power Supply Regulatory CE, RoHS

Other

Standard Warranty 5 years
Included Accessories Quick Install Guide, (3) 3-pin Phoenix connectors, (7) 5-pin Phoenix connectors, (1)

3.5mm Audio Cable (for IR cascading), IR Remote, (1) IR Emier, (1) IR Receivers, (1)

DC24V 6A power supply with US power plug, (2) Rack mount ears with 6 mounng

screws, (4) Plasc Cushions
Compable Transmiers INT-HD70-TXWP, INT-HD70-TX, AS-1H1V, AS-1H1V-WP-W., AS-2H, AS-2H-WP-W, INT-

HD52

Distances and picture quality may be aected by cable grade, cable quality, source and desnaon equipment, RF and electrical interference, and cable

patches.

10

INT-PS82-H2 Quick Guide

Technical Specicaons - HDBaseT Receiver

Supported Audio and Video

Video Compliance HDMI 2.0a, HDCP 2.2, CEC
Output Resoluon Support SMPTE: Up to 4096x2160@60Hz (4:4:4 chroma sub-sampling / 8 bit deep color)

VESA: Up to 1920x1200
Embedded Audio 2 Channel Stereo
IR Carrier Frequency Range 33-55kHz at 5 volts
RS232 Baud Rate up to 115200

HDBaseT Signal Characteriscs

Maximum Distance 70 m (up to 1080p) , 40 m (up to 4K@60Hz / 4:2:0 / 8 bit deep color)
Cable Requirements Solid core shielded Category 6 F/UTP cable or greater with TIA/EIA-568B crimp paern
Bandwidth 18Gbps

Chassis and Environmental

Dimensions (WxHxD) 115 mm x 16 mm x 84 mm (4.5 in x .6 in x 3.3 in)
Shipping Weight 153g (.3 lbs.)
Operang Temperature 0° to +40° C (+32° to +104° F)
Operang Humidity 10% to 90%, Non-condensing
Storage Temperature -10° to +50° C (+14° to +122° F)
Storage Humidity 10% to 90%, Non-condensing

Power, ESD, and Regulatory

Power Consumpon 14 was (max)
ESD Protecon 15kV
Product Regulatory FCC, CE, RoHS
Power Supply Regulatory CE, RoHS

Other

Standard Warranty 5 years

Distances and picture quality may be aected by cable grade, cable quality, source and desnaon equipment, RF and electrical interference, and cable

patches.

11

Thank you for your purchase.

For Technical Support please call our toll free number at

800-530-8998 or email us at [e-mail]

www.libav.com

Intelix is a brand of:

11675 Ridgeline Drive
Colorado Springs, Colorado
80921 USA
Phone: [phone]
Fax: [phone]
Toll-Free: 800-530-8998