Intelix INT-HD52 Quick Start Guide

INT-HD52 Quick Install Guide
This guide is for quick installaon only.
For complete owners manual go to www.libav.com or use a QR reader to access
the manual via QR code below.
Scan QR Code with your Smart-phone or Tablet
Important noce:
Do not aempt to disassemble or alter the housing. There are no user-serviceable parts
inside the unit. Doing so will void your warranty.
To minimize the possibility of equipment damage from electrostac discharge (ESD), all source and
desnaon equipment must be powered o during installaon.
Do not connect the device to a telecommunicaon outlet wired to unrelated equipment. Doing so may damage the unit or any connected equipment. Ensure all connected twisted pair cabling is straight-through (point-to-point).
Allow proper venlaon to reduce the risk of thermal failure.
The Intelix INT-HD52 is a 5 input mul format A/V presentaon auto switcher that scales video signals to an HDMI and HDBaseT output simultaneously. HDBaseT output supports PoH and can connect to a compable HDBaseT receiver up to a maximum of 70 meters / 230 feet (HDBaseT receiver sold separately). With 1 IR In and 1 IR Out and 1 RS232, the IR and RS232 control signals can be transmied bi-direconally between the INT-HD52 and a compable HDBaseT receiver. The INT­HD52 can be controlled either by front panel buons, IR remote, IP, RS232 or web based GUI. With a microphone input that supports phantom power and a balanced stereo audio output for audio reinforcement, the INT-HD52 can handle a myriad of A/V applicaons.
Front Panel
1. Built in IR Receiver
2. Power Indicator - GREEN when device is in standby mode, RED when device is powered on and no indicator when there is no power to device
3. 1-HDMI/MHL input selector and acvity LED / Le Key for On screen display control (OSD)
4. 2-HDMI input selector and acvity LED / Right Key for OSD
5. 3-HDMI input selector and acvity LED / Up Key for OSD
6. 4-Display Port input selector and acvity LED / Down Key for OSD
7. 5-VGA input selector and acvity LED / Enter Key for OSD
8. Auto Switching selector and acvity LED- Press this to enter / exit auto-switching mode / OSD menu buon
NOTE: When you set the VGA input port to C-Video or YPbPr in Manual-switching mode, the system will not be able to enter auto-switching mode.
Hold this buon down for 3 seconds to enter On Screen Display menu (OSD)
9. Volume knob for variable audio control- Push knob in to toggle between ‘Mic’ and ‘Source’ control
Rear Panel
1. INPUTS
Video input ports: 1 HDMI/MHL, 2 HDMI inputs, 1 Display Port and 1 VGA
Audio input ports: 1 Display Port external audio input and 1 VGA auxiliary audio input
2. OUTPUTS
HDMI output: HDMI video output port
HDBaseT output: Supports PoH. Connect to a compable HDBaseT receiver to transmit A/V, IR
and RS232 control
3. MIC INPUT
Mic audio port connects to microphone
Dial switch- switches between 3 dierent modes; 48V for condenser mics, MIC mode for dynamic
mics and LINE mode for line level audio
4. CONTROL
RES RESET - press this to reset output resoluon to 720p or to acvate HDMI and HDBT outputs if they have been turned o
IR IN / IR OUT - connect with IR receiver and emmiter to control devices via IR
FIRMWARE - Type-A USB port for updang rmware
RS232 - Serial port, connect a control device to control the INT-HD52
TCP/IP - Ethernet port, connect a control device or computer to control INT-HD52
5. AUDIO OUTPUT
Stereo balanced L/R audio output
6. DC 24V
Locking power port, connect DC 24V power adapter
Connecvity Instrucons
1. Verify all components included are present before installaon.
2. Connect HDMI source devices to HDMI inputs 1-3
3. Connect a Display Port source device to DP input
4. Connect a VGA source device to VGA input
5. Select appropriate MIC level mode and connect microphone to MIC input port
6. Connect an HDMI display device to the HDMI output port
7. Connect a compable HDBaseT receiver such as the Intelix INT-HD70-RX to the HDBT output port with twisted pair cabling
8. Connect AUDIO OUTPUT port to audio amplier or powered speakers
9. Connect control devices (control systems) to the TCP/IP port for IP control
10. Connect control devices (control systems) to the RS232 for serial control
11. Connect IR eye to the IR EYE port so the INT-HD52 can be controlled via IR remote in rack cabinets or underneath a conference table
12. Both the INT-HD52 and a compable HDBaseT receiver will have an IR IN and an IR OUT. When one device is connected with an IR emier to the IR OUT then the other device should be connected with an IR eye into IR IN
13. Plug the power supply into the power input port of the INT-HD52
14. Power on aached audio/video devices.
Note: A compable HDBaseT receiver can be powered by the INT-HD52 when connected to the HDBT output. However an HDBaseT receiver cannot power the
INT-HD52
Technical Specications
VIDEO
Video Inputs (3) HDMI; (1) Display Port; (1) VGA
Video Input Connector (3) HDMI type A; (1) Display Port female; (1) VGA female 15 pin
Input Video Signal HDMI, DP, YPbPr, C-video, VGA
Video Output (1) HDMI;
Video Output Connector (1) HDMI type A
Output Video Signal HDMI; HDBaseT
Output Resolution 1920x1200; 1920x1080; 1600x1200; 1600x900; 1360x768; 1280x800;
Standards Compliant with HDMI 1.4 & HDCP2.2
Audio
Audio Input (1) stereo audio input for DP, (1) stereo audio input for VGA
Audio Input Connector (2) 3.5mm Stereo jacks; (1) 3-Pin phoenix
Audio Input Impedance > 10k Ohm
Audio Output 1 Dual-Mono analog
Audio Output Connector (1) 5 Pin phoenix
Audio Output Impedance 70 Ohms
Frequency Response 20Hz~20K Hz
Stereo Channel Separation >80dB @1KHz
CONTROL
Control Port (1) IR IN
Control Connector (3) 3.5mm mini jack (IR)
Other
Transmission Distance 1080p 70m or less when using Cat6
Temperature 0 ~ +50 C
Humidity 10% ~ 90%
Power Supply DC24V 2.71A
Power Consumption 27W
Dimension (W*H*D) 8.6” x 1.73” x 6.79”
Weight 2 lbs
Warranty 2 years
Included Accessories
(1) HDBaseT
(1) RJ45
1280x720; 1024x768
(1) Microphone audio
(1) IR OUT (1) IR EYE (1) RS232 (1) TCP/IP
(1) 3 pin phoenix connector (RS232) (1) RJ45 (TCP/IP)
(2) Mounting ears with screws; (1) power adapter (24VDC, 2.71A); (4) plastic cushions (1) IR Remote; (1) VGA to component breakout cable; (1) RS232 to 3 pin phoenix breakout cable; (1) IR emitter (1) IR eye; (1) Quick Install Guide
Intelix
11675 Ridgeline Drive
Colorado Springs, CO 80918
800-530-8998
supportlibav@libav.com
rev 170110
Thank you for your purchase.
For Technical Support please call our toll free number at
800-530-8898 or email us at supportlibav@libav.com
www.intelix.com
www.libav.com
Intelix is a brand of:
11675 Ridgeline Drive Colorado Springs, Colorado 80921 USA Phone: 719-260-0061 Fax: 719-260-0075 Toll-Free: 800-530-8998
Loading...