Intelix DL-ARK-4HC, DL-ARK-3H1VC Install Guide

DL-ARK Quick Install Guide

Rev 190306

DL-ARK-4HCDL-ARK-3H1VC

This guide is for quick installaon only.

For complete owners manual go to www.libav.com or use a QR reader to access the

manual via QR code below.

Scan QR Code with your Smart-phone or Tablet

11675 Ridgeline Drive

Colorado Springs, CO

80921

Toll-Free: 800-530-8998

Phone: [phone]

Fax: [phone]

DL-ARK Quick Guide

Product Overview

The Digitalinx DL-ARK Advanced Room Kit is a mul-funcon A/V distribuon and push buon control
system designed to provide audio, video and USB 2.0 data extension with complete system control
all in one convenient system. Only two solid core, shielded Category 6 cables are required to connect
the enre system together which consists of one HDBaseT wall plate transmier, one HDBaseT
receiver and one keypad controller. All the power needed for the keypad and wall plate transmier is
provided by the receiver via Category cable / HDBaseT.

There are two systems available in the series; the DL-ARK-3H1VC features 2 HDMI inputs and 1 VGA
with audio input on the wall plate transmier and the DL-ARK-4HC features 3 HDMI inputs on the
wall plate transmier. Both HDBaseT transmiers features a USB B host port for connecon to a
computer or host and a dedicated audio input that is independent of all video inputs. The DL-ARK
HDBaseT receiver for both systems provides an addional HDMI input for a local A/V input, an HDMI
output for a display or projector, a 3 port client USB hub for connecon to interacve white board
or USB mic / camera, a two port LAN switch, mic / line analog audio input, line audio analog output,
40 wa 70 volt power amplier output and an RS232 and IR output for display or projector control
either by keypad controller or web server. The DL-ARK control keypad for both systems features audio
and video input selecon control for all A/V inputs, variable audio control for the mic/line input, line
audio output and amplied audio output from the DL-ARK receiver and can control a connected
display or projectors ON and OFF status via RS232 or IR from the receiver as well. The DL-ARK
systems are UL Listed.

Several DL-ARK systems can be remotely managed by the DL-ARK system management soware
which allows centralized status view and control of a system from anywhere on the LAN.

2

DL-ARK Quick Guide

Connecvity Instrucons

1. Verify all components included with the DL-ARK A/V system are present before installaon.

2. If the receiver is going to be permanently mounted to a surface or A/V box, aach the included
mounng brackets with the supplied screws.

3. Turn o power and disconnect the audio/video equipments by following the manufacturer’s
instrucons.

4. Connect Category 6 or greater twisted pair cable between the DL-ARK control pad and transmier
up to 30m / 100’, then connect a Category 6 or greater cable between transmier and the receiver up
to 70m / 232’. TIA/EIA-568B straight-through wiring connecons must be used.

5. Connect an HDMI cable no greater in length then 5m / 16’ and any desired IR or RS232 control
accessories between the display and the DL-ARK receiver.

6. Connect an HDMI cable no greater than 5m / 16’ in length between the source and the DL-ARK
transmier.

7. Mount the keypad and wall plate transmier.

8. Connect the included power supply to the DL-ARK receiver and lock the power supply to the power
connector by twisng the locking collar clockwise.

9. Power on aached audio/video devices.

Cabling Wiring Requirements

HDBaseT Cabling

To ensure proper performance of the DL-ARK, it is recommended that you use solid core, shielded
Category 6 F/UTP cabling at a minimum between control pad and transmier and between transmier
and receiver. Category 5e F/UTP may perform well but may not support power over HDBaseT reliably
over longer distances.

When using shielded category cabling ALWAY S ...

....use shielded connectors

....properly ground the category cable

For opmized HDBaseT performance use the following Liberty Wire and Cable branded cabling;

Category 6 plenum; 24-4P-P-L6SH
Category 6A plenum; 24-4P-P-L6ASH

Category 6 NON-plenum; 24-4P-L6SH
Category 6A NON -plenum; 24-4P-L6ASH

Twisted Pair Wiring

Use TIA/EIA-568B wiring for Category 6
connecon between send and receive
units.

3

Thank you for your purchase.

For Technical Support please call our toll free number at

800-530-8998 or email us at [e-mail]

www.libav.com

Digitalinx is a brand of:

11675 Ridgeline Drive
Colorado Springs, Colorado
80921 USA
Phone: [phone]
Fax: [phone]
Toll-Free: 800-530-8998