The Digitalinx DL-1H1A1U-WPKT-W HDBaseT 2.0 extender set transmits HDMI, audio
, USB High Speed (up to 190Mbps) and RS232 over single category 6 twisted pair
cable. The DL-1H1A1U-WPKT-W can transmit 4K resoluons up to 4K@60Hz, 4:2:0 up
to 40m / 120’ and 1080P up to 70m / 230’. The audio circuit is completely separate
and is not dependent on the HDMI or USB input source to be acve. The Digitalinx
DL-1H1A1U-WPKT-W is HDMI 1.4b and HDCP 2.2 compliant and supports CEC pass
through.
The DL-1H1A1U-WPKT-W HDBaseT receiver powers wall plate transmier via HDBaseT
so there is no need for an external power supply for the wall plate.
The DL-1H1A1U-WPKT-W is sold only as a set. The individual transmier and receiver
are not compable with other HDBaseT devices due to proprietary PoE circuitry.
Package Contents
• DL-1H1A1U-WPKT-W Wall plate extender set
• Quick Install Guide
• (1) Decora cover plate
• (1) 3 Pin phoenix connector
• (1) 2 Pin phoenix connector
• (1) DC24V 1A power supply with US, UK, EU and AU power adapter plugs
• (2) Mounng ears with mounng screws
2
Transmier
DL-1H1A1U-WPKT-W Install Guide
Transmier / Receiver View
1
1
5
2
2
1. HDMI IN - Video source input
2. ACTIVE LED
• When LED is green, unit is received acve HDMI signal
• When LED is o, no acve HDMI signal is present
3. AUDIO IN - 3.5 mm analog audio source input
4. USB - USB host port
5. RS232 - Serial port for transming / receiving RS232 signals
6. HDBaseT OUT - HDBaseT output port
7. DC24V - Phoenix connector for connecng external power supply
Note: The DL-1H1A1U-WPKT-W-TX can receive power via HDBaseT from the receiver when
connected together with a Category 6 F/UTP cable
3
3
4
67
3
DL-1H1A1U-WPKT-W Install Guide
Receiver
1
1. ACTIVITY LED’S
• When POWER LED is ON, unit is receiving power
• When LINK LED is ON, the TX and RX is connected properly
• When HDCP LED is ON, unit is receiving HDCP encrypted content
• When FW LED is ON, unit is receiving power
2. SERVICE - For rmware updates
3. HDBaseT IN - HDBaseT input port
4. HDMI OUT - HDMI output to connect to display technology
5. USB - USB Client side ports
6. AUDIO OUT - 3.5mm analog audio output port
7. RS232 - Serial port for transming / receiving RS232 signals
8. DC24V - Locking connector for connecng external power supply
2
3
4
56
78
4
DL-1H1A1U-WPKT-W Install Guide
Connecvity Instrucons
1. Verify all components included with the extender set are present before installaon.
2. If the extenders are going to be permanently mounted to a surface, aach the
included mounng brackets with the supplied screws.
3. Turn o power and disconnect the audio/video equipment by following the
manufacturer’s instrucons.
4. Connect Category 6 or greater twisted pair cable with RJ45 connectors between the
transmier (DL-1H1A1U-WPKT-W-TX) and the receiver (DL-H1A1U-WPKT-W-RX). TIA/
EIA-568B straight-through wiring connecons must be used with all HDBaseT extenders.
5. Connect an HDMI cable and any desired control accessories between the display and
the receiver (DL-H1A1U-WPKT-W-RX).
6. Connect an HDMI cable and any desired control accessories between the source and
the transmier (DL-1H1A1U-WPKT-W-TX).
7. Connect a computer USB port to the transmier (DL-1H1A1U-WPKT-W-TX) USB host
port.
8. Connected USB peripherals such as white-boards and USB cameras the to USB client
ports of the receiver (DL-1H1A1U-WPKT-W-RX) USB ports.
9. Connect the included power supply to the DL-1H1A1U-WPKT-W receiver and lock
the power supply to the power connector by twisng the locking collar clockwise.
10. Power on aached audio/video devices.
5
DL-1H1A1U-WPKT-W Install Guide
Cabling Requirements
HDBaseT Cabling
To ensure proper performance of the DL-1H1A1U-WPKT-W, it is recommended that you
use solid core, shielded Category 6 F/UTP cabling at a minimum. Category 5e F/UTP may
perform well but may not support power over HDBaseT reliably.
When using shielded category cabling ALWAY S...
....use shielded connectors
....properly ground the category cable
For opmized HDBaseT performance use the following Liberty Wire and Cable branded
Category 6 NON-plenum; 24-4P-L6SHCategory 6A NON -plenum; 24-4P-L6ASH
TX G RX
RS232 Port
Twisted Pair Wiring
Use TIA/EIA-568B wiring for Category 6
connecon between send and receive
units.
RS232 Wiring
Connect the controller or device RX signal
to TX on the DL-1H1A1U-WPKT-W extender.
Connect the controller or device TX signal to
Rx on the DL-1H1A1U-WPKT-W extender.
Connected RS232
Device Pins
RX G TX
6
DL-1H1A1U-WPKT-W Install Guide
Technical Specicaons
VIDEO
Video Inputs (TX)(1) HDMI
Video Input Connector (TX)(1) HDMI type A
Input Video SignalHDMI
Video Output (RX)(1) HDMI
Video Output Connector (RX)(1) HDMI type A
Output Video SignalHDMI
Input Resoluons SupportedUp to 3840 x 2160 @ 60Hz, 4:2:0, 8bit color depth
StandardsCompliant with HDMI 1.4b & HDCP2.2
USB
Supported USB StandardUSB 2.0 High Speed
USB Data Transfer Bandwidth190Mbps
USB Port Type(1) USB Type B (TX)