Intelix DIGI-HD-UHR2-R, DIGI-HD-UHR2-S, DIGI-HD-UHR2 Series Installation Manual

8001 Terrace Ave.
Suite #201
Phone: 608-831-0880
Toll-Free: 866-4-MATMIX
Fax: 608-831-1833
Maximum Recommended Distances
1080p
1080i
720p
576i/p
480i/p
Cat 6a
(shielded)
150’
300’
300’
300’
300’
Cat 6
110’
220’
220’
220’
220’
Cat 5e
100’
200’
200’
200’
200’
Caution: Do not attempt to disassemble or alter the extender housing. There are no user-serviceable parts inside the unit. Doing so will void your warranty.
Instructions
1. Turn off power and disconnect the
audio/video equipment by following the manufacturer’s instructions.
2. Make certain that outlets and cross connects
to which you will connect the DIGI-HD-UHR2 are configured properly and labeled correctly to identify the point-to-point circuit.
3. Verify the desired twisted pairs are not being
used for other LAN or telephony equipment.
4. Verify that the source and destination
equipment work when directly connected with HDMI cables. Be sure to test both HDMI cables required for system installation.
5. Connect the DIGI-HD-UHR2 transmitter to the
HDMI output of the video source. Do not connect the 5V power supply.
6. Connect the DIGI-HD-UHR2 receiver to the
HDMI input of the receiving device at the remote end. Do not connect the 5V power supply.
7. Complete the connection between the
transmit and receive extenders using twisted pair cable. Ensure the cable conforms to EIA 568B crimp standards and there are no split pairs or taps.
8. Connect the 5V power supply to the DIGI-HD-
UHR2 receiver.
9. Connect the 5V power supply to the DIGI-HD-
UHR2 transmitter. Power-on the video equipment.
10. Verify picture quality.
11. If necessary, adjust the DIP switches on the
transmit and receive extenders to select modes of operation.
12. If necessary, copy the EDID information from
your display for improved performance.
Caution: To minimize the possibility of equipment damage from electrostatic discharge (ESD), all source and destination equipment must be powered off during installation.
DIGI-HD-UHR2 Installation Manual
The Intelix DIGI-HD-UHR2 transmits HDMI up to 300’ over a single twisted pair cable. In environments with high electromagnetic interference (EMI), a shielded twisted pair cable should be used.
Built-in HDshāk® technology provides dynamic HDMI, EDID/DDC and HDCP mode selection, guaranteeing performance and image quality. Plus, onboard HDMI amplification and buffering allows multiple extenders to be daisy-chained for greater distances.
The DIGI-HD-UHR2 features electrostatic discharge (ESD) protection circuitry which safegaurds the HDMI circuit against static electricity and other destructive stray voltage.
Design with Intelix and Design with Intelligence.
8001 Terrace Ave.
Suite #201
Phone: 608-831-0880
Toll-Free: 866-4-MATMIX
Fax: 608-831-1833
DIGI-HD-UHR2 Transmitter Dip Switch Positions
SW 1
SW 2
Mode
Off
Off
Read EDID data from displays
Off
On
1080p with multi-channel audio
On
Off
1080p with stereo audio
On
On
No function
DIGI-HD-UHR2 Receiver Dip Switch Positions
SW 1
SW 2
Mode
Off
Off
Normal Operation
Off
On
Compatibility Mode
On
Off
Compatibility Mode
On
On
No function
Troubleshooting
Symptom
Possible Solutions
No signal
Status LED is off
Verify that both ends of the twisted pair cable use 568B crimp pattern.
Verify HDMI cables and source and destination HDMI ports are operational.
No signal
Verify the power supplies are connected to both the send and receive baluns.
Verify the power LEDs on both the send and receive units are brightly illuminated.
Unusual colors in the video
Power off the destination device and power it back on to force renegotiation.
Unplug and re-plug the HDMI cable from receive balun to force renegotiation.
No signal
Screen is completely snowy
Speckling in the video image
Occasional signal dropouts
Video without audio
Use a shorter run of twisted pair cabling.
Drop the HDMI signal to the next lower resolution; i.e., decrease resolution from 1080p to 1080i, etc.
Replace the twisted pair cable with a higher grade twisted pair cable; i.e., replace Cat 5e with Cat 6.
Activate compatibility mode.
Speckling in the video image
If the destination device is incapable of displaying the video signal, alter the source signal; i.e., decrease resolution from 1080p to 1080i, etc.
Video without audio
Change source device to output PCM other than Bitstream audio
Enable PCM down sampling if supported by your source device
Copying Display EDID
1. Disconnect the transmitter from the source device.
2. Disconnect the receiver from the display.
3. Connect the transmitter to the destination device via an
HDMI cable.
4. Connect the 5VDC power supply to the transmitter.
5. Press the Copy EDID button. The Status LED will flash and
remain solid. The EDID signals have been copied and stored.
6. Disconnect the transmitter and repeat normal
installation procedures.
*The DIGI-HD-UHR2 system must be power cycled for the changes to take effect.
*The DIGI-HD-UHR2 system must be power cycled for the changes to take effect.
The Intelix DIGI-HD-UHR2 conforms to HDMI and HDCP specifications. Intelix does not guarantee operation with devices that do not conform to these specifications.
Distances and picture quality may be affected by cable grade, cable quality, source and destination equipment, RF and electrical
interference, and cable patches.
Loading...