
8001 Terrace Ave.
Suite #201
Middleton, WI 53562
Phone: 608-831-0880
Toll-Free: 866-4-MATMIX
Fax: 608-831-1833
Maximum Recommended Distances
Instructions
1. Turn off power and disconnect the
audio/video equipment by following the
manufacturer’s instructions.
2. Adjust DIP switches for desired mode.
3. Connect all Cat5e cables (ensure T568B
straight-thru wiring).
4. Connect all HDMI cables.
5. Connect power supplies.
6. Power on attached audio/video devices.
Compatible Devices
Compatible Receivers: DIGI-HD-IR3-R, DIGI-HD-IR3-WP-R,
*DIGI-HD-IR2-R
Compatible Transmitters: DIGI-HD-IR3-S, DIGI-HD-IR3-WP-S,
*DIGI-HD-IR2-S, DIGI-HD-4X2, DIGI-HD-4X4, DIGI-HD-4X8,
DIGI-HD-8X8,
*when paired with 2-series extenders, bi-directional IR
is not supported; only source-to-display
Important notice:
Do not attempt to disassemble or alter the extender
housing. There are no user-serviceable parts inside the
unit. Doing so will void your warranty.
To minimize the possibility of equipment damage from
electrostatic discharge (ESD), all source and destination
equipment must be powered off during installation.
Do not connect the extender to a telecommunication outlet
wired to unrelated equipment. Doing so may damage the
unit or any connected equipment. Ensure all connected
twisted pair cabling is straight-through (point-to-point).
Allow proper ventilation to reduce the risk of thermal
failure.
DIGI-HD-IR3-WP Installation
Manual
The Intelix DIGI-HD-IR3-WP transmits HDMI and IR up to 300’
over two twisted pair cables. In environments with high
electromagnetic interference (EMI), shielded twisted pair
cable should be used.
Built-in HDshāk® technology provides dynamic HDMI,
EDID/DDC and HDCP mode selection, guaranteeing
performance and image quality. Plus, onboard HDMI
amplification and buffering allows multiple extenders to be
daisy-chained for greater distances.
The DIGI-HD-IR3-WP features electrostatic discharge (ESD)
protection circuitry which safegaurds the HDMI circuit against
static electricity and other destructive stray voltage.
The Intelix DIGI-HD-IR3-WP conforms to HDMI and HDCP specifications.
Intelix does not
guarantee
operation with
devices that do
not conform to
these
specifications.
The Intelix DIGIHD-IR3-WP
complies with
HDCP standards.
Distances and
picture quality
may be affected by cable grade, cable quality, source and destination
equipment, RF and electrical interference, and cable patches.

8001 Terrace Ave.
Suite #201
Middleton, WI 53562
Phone: 608-831-0880
Toll-Free: 866-4-MATMIX
Fax: 608-831-1833
DIGI-HD-IR3-WP-S Transmitter Dip Switch Positions
EDID Information from DDC
Use Copied EDID (Run Mode)
EDID copy (Acquire and store)
DIGI-HD-IR3-WP-R Receiver Dip Switch Positions
No signal
Status LED is off
Verify that both ends of the twisted pair cables
use 568B crimp pattern.
Verify HDMI cables and source and destination
HDMI ports are operational.
Verify the power supplies are connected to both
the send and receive baluns.
Verify the power LEDs on both the send and
receive units are brightly illuminated.
Unusual colors in the
video
Power off the destination device and power it
back on to force renegotiation.
Unplug and re-plug the HDMI cable from receive
balun to force renegotiation.
No signal
Screen is completely
snowy
Speckling in the video
image
Occasional signal dropouts
Use shorter runs of twisted pair cabling.
Drop the HDMI signal to the next lower
resolution; i.e., decrease resolution from 1080p
to 1080i, etc.
Replace the twisted pair cable with a higher
grade twisted pair cable; i.e., replace Cat 5e with
Cat 6.
Speckling in the video
image
If the destination device is incapable of displaying
the video signal, alter the source signal; i.e.,
decrease resolution from 1080p to 1080i, etc.
Change source device to output PCM other than
Bitstream audio
Enable PCM down sampling if supported by your
source device
Copying Display EDID
1. Disconnect the transmitter from the source device.
2. Disconnect the receiver from the destination device.
3. Set transmitter DIP switches to EDID Copy mode (On,
Off, On)
4. Connect the transmitter to the destination device via an
HDMI cable.
5. Connect the 5VDC power supply to the transmitter.
6. The Status LED will flash for 2-3 seconds then remain
solid. The EDID signals have been copied and stored.
7. Disconnect the transmitter from the destination.
8. Change DIP switch settings to EDID Run Mode (On, Off,
Off)
9. Reconnect the transmitter and receiver following
normal installation procedures.
DIP Switch Settings
*The DIGI-HD-IR3 system must be power cycled for the changes
to take effect. Please remove ALL cables from extender, change
DIP switches, and then reconnect.
DIP Switch Settings
1. DIGI-HD-IR3-WP-S
a. 1080p, Stereo Audio – The transmitter is preset
with EDID for 1080p video and PCM stereo audio.
b. 1080p, 5.1 Audio – The transmitter is preset with
EDID for 1080p video and Dolby Digital 5.1, DTS
5.1, and PCM stereo audio.
c. EDID from DDC – The receiver sends dynamic EDID
to the transmitter via the 2nd Cat 5e cable.
d. Use Copied EDID (Run Mode) – The transmitter
2. DIGI-HD-IR3-WP-R
uses custom EDID copied into the transmitter
during installation.
e. EDID copy (Acquire and store) – Installation only
setting used during EDID copy process.
f. 1080i, Stereo Audio – The transmitter is preset
with EDID for 1080i video and PCM stereo audio.
a. Normal Mode – Factory default works in most
applications.
b. Compatibility Mode – Certain sources may create
an unstable video image. This may include some
cable/satellite receivers. Try using this setting if
you witness an image that flashes on/off
approximately every 2 seconds.