Intelix DIGI-HD70 Installation Manual

Page 1
8001 Terrace Ave. Suite #201 Middleton, WI 53562
Troubleshooting
Symptom
Possible Solutions
No signal
Status LED is off
Verify that both ends of the twisted pair cables use T568B crimp pattern.
Verify HDMI cables and source and destination HDMI ports are operational.
No signal
Verify the power supplies are connected to both the send and receive baluns.
Verify the power LEDs on both the send and receive units are brightly illuminated.
Unusual colors in the video
Power off the destination device and power it back on to force renegotiation.
Unplug and re-plug the HDMI cable from receive to force renegotiation.
Important notice:
Do not attempt to disassemble or alter the
extender housing. There are no user-serviceable parts inside the unit. Doing so will void your warranty.
To minimize the possibility of equipment damage
from electrostatic discharge (ESD), all source and destination equipment must be powered off during installation.
Do not connect the extender to a
telecommunication outlet wired to unrelated equipment. Doing so may damage the unit or any connected equipment. Ensure all connected twisted pair cabling is straight-through (point-to­point).
Allow proper ventilation to reduce the risk of
thermal failure.
Instructions
1. Turn off power and disconnect the
audio/video equipment by following the manufacturer’s instructions.
2. Connect twisted pair cable between the
transmitter (DIGI-HD70-S) and the receiver (DIGI-HD70-R). Ensure T568B straight-thru wiring.
3. Connect HDMI cables between the display
and the receiver (DIGI-HD70-R).
4. Connect HDMI cables between the source
and the transmitter (DIGI-HD70-S).
5. Connect the included power supplies to the
transmitter and receiver.
6. Power on attached audio/video devices.
DIGI-HD70 Installation Guide
Twisted Pair Wiring - Use
T568B wiring for Cat5e/6 connection between send and receive units.
The Intelix DIGI-HD70 extends HDMI over a single twisted pair cable. The DIGI-HD70 supports a 1080p video signal up to 70m, as well as 3D and 4K x 2K signals up to 40m.
Built-in surge protection and diagnostic LEDs ensure hassle-free and robust installations. The DIGI-HD70 incorporates HDBaseT technology.
Page 2
8001 Terrace Ave. Suite #201 Middleton, WI 53562
Technical Specifications
I/O Connections
HDMI
HDMI Type A Receptacle Connector
Twisted Pair
Shielded RJ45 Female
5V DC Power
5.5 mm Outside Diameter, 2.1 mm Inside Diameter Barrel
Supported Audio and Video
Maximum Video Compatibility at 70 m
Deep Color 36/30/24 Bit at 1080p
Maximum Video Compatibility at 40 m
Deep Color 48 Bit at 1080p, 3D, and 4k x 2k
Video Compliance
HDMI, HDCP, and CEC (Consumer Electronics Control)
Embedded Audio
Up to PCM 8 channel, Dolby Digital TrueHD, and DTS-HD Master Audio
Input DDC Signal
5.0 volts p-p (TTL)
Input Video Signal
0.5 to 1.0 volts p-p
HDBaseT Signal Characteristics
Maximum Distance
70 m
Bandwidth
10.2 Gbps
Gain
0 dB – 10 dB at 100 MHz
Resolution Range
800x600 – 1920x1200
Signal to Noise Ratio (SNR)
> 70 dB at 100 MHz over 100 m
Return Loss
< -30 dB at 5 KHz
Total Harmonic Distortion (THD)
< 0.005% at 1 KHz
Min-Max Signal Level
< 0.3 V – 1.45 Vp-p
Differential Phase Error
±10° at 135 MHz over 100 m
Chassis and Environmental
Enclosure
Painted steel
Dimensions
110mm x 76mm x 24mm (4.33 in. x 2.99 in. x 0.95 in.)
Shipping Weight
0.5 kg (1.1 lbs.)
Operating Temperature (Environment)
0° to +40° C (+32° to +104° F)
Operating Temperature (Chassis)
31° C (88° F) (S); 38° C (100° F) (R)
Operating Humidity (Environment)
20% to 90%, Non-condensing
Storage Temperature (Environment)
-10° to +60° C (+14° to +140° F)
Storage Humidity (Environment)
20% to 90%, Non-condensing
Power, ESD, and Regulatory
Maximum Power Consumption
4 watts (S), 11 watts (R)
Power Supply
5vDC / 2A
ESD Protection
15kV
Regulatory
CE, RoHS
Other
Standard Warranty
2 Years
Diagnostic Indicators
Link and power LEDs
DIGI-HD70-R Compatible Transmitters
DIGI-HD70-S, FLX-BO4
DIGI-HD70-S Compatible Receivers
DIGI-HD70-R, FLX-BI4
Included Accessories
Power Supply, Installation Guide
Loading...