Intelix AVO-CLIP-F User Manual

Specifications

Specifications subject to change without notice.

AVO-CLIP Contents (1) Angle Mounting Bracket

(1) DIN Rail Clip
(2) DIN Rail Clip Mounting Screws
(4) Tie Fasteners

Bracket Dimensions 3.25” x 1.25” x 3.00”

Bracket Material Black Aluminum

DIN Rail Clip Dimensions 1.75” x 0.75” x 0.40”

DIN Rail Clip Material Molded Plastic

DIN Rail Compatibility 35 mm DIN rail

Tie Fastener Length 11”

Overall Mounted Height 4” (3 rack units)

Intelix DIN-RACK-KIT The Intelix DIN-RACK-KIT supports up to
Compatibility 26 AVO-CLIPs

Weight 0.2 lbs

Ordering Information AVO-CLIP

Warranty 2 years

Intelix Balun (1) AVO-A2 (1) AVO-A4 (1) V3AD
Compatibiltiy (1) AVO-SVA2 (2) AVO-V1 (1) V3

(2) AVO-V1-ST (1) AVO-V1A2 (1) V2A2
(1) AVO-V2A2 (1) AVO-V3 (2) V1-ST
(1) A2 (1) A4 (1) V1-PTZ
(1) SVA2 (2) VB (2) V1-CV
(2) V1 (1) V1-AR (1) V1A2

AvoCat

Series

Intelix AVO-CLIP Mounting Clip

InsIns

tt

allation Manualallation Manual

Ins

t

allation Manual

InsIns

tt

allation Manualallation Manual

The Intelix AVO-CLIP allows Intelix AvoCat Series
and Classic Series baluns to be mounted on a 19” rack
tray, standard DIN rail, or any other screw-mountable
surface. Each AVO-CLIP contains a universal
mounting bracket, DIN rail converter clip, two
mounting screws, and four fasteners.

The Intelix AvoCat Series of baluns is the ideal
solution for sending audio and video over structured
cabling. When signal quality matters, choose Intelix.

Installation

Caution: Do not mount the balun over equipment ventilation openings. Covering the

To install an AVO-CLIP balun, perform the following steps:

1. Verify the AVO-CLIP kit contents are complete (see Specifications) and the balun(s)
you wish to mount are compatible.

2. Determine where the AVO-CLIP will be mounted. If mounting to a 35 mm DIN rail
or the Intelix DIN-RACK-KIT, continue to step 3a. If mounting to a flat surface,
skip to step 4a.

openings may cause the equipment to overheat.

* DVI, HDMI, PS2, VGA-HR, VGA-UHR, and VGA2
are sold in pairs. One AVO-CLIP is required for the
send unit and one AVO-CLIP is required for the recieve
unit.

Contact Information

Intelix

2222 Pleasant View Road
Middleton, WI 53562

Toll-free: 866-4-MATMIX
Phone: [phone]
Fax: [phone]

www.intelix.com

3 a. Mount the angle mounting bracket to the DIN rail clip with the two DIN rail clip

screws.

b. Secure the balun(s) to the angle bracket with the included tie fasteners. Two tie

fasteners should be used per balun.

c. Mount the AVO-CLIP and balun to a 35 mm DIN rail or the Intelix DIN-

RACK-KIT.

d. The AVO-CLIP and balun are successfully installed.

4. a. Secure the angle mounting bracket to a flat surface by mounting the appropriate

screws (wood screws for a wooden surface, metal screws for a metal surface)
through the round holes on the base of the bracket.

b. Secure the balun(s) to the angle bracket with the included tie fasteners. Two tie

fasteners should be used per balun.

d. The AVO-CLIP and balun are successfully installed.

Mounted AVO-CLIP Pictures

Two Intelix AVO-V1 baluns mounted to
an Intelix AVO-CLIP on a 35 mm DIN
rail.

One Intelix AVO-V1A2 balun mounted to
an Intelix AVO-CLIP on a 35 mm DIN
rail.

AVO-CLIP Components

Two Intelix AVO-CLIPs mounted to the
Intelix DIN-RACK-KIT.