PD9130, PD9140A, PD9145A, PD9155, PD9160A, PD9180
OWNERS MANUAL
PROGRESSIVE DYNAMICS, INC.
POWER CONVERTER LIMITED WARRANTY
I. LIMITED WARRANTY: Progressive Dynamics, Inc. warrants its power converter to be free from defects in
material or workmanship under normal use and service; and limits the remedies to repair or replacement.
II. DURATION: This warranty shall extend for a period of two years from the original date of purchase, and is
valid only within the continental limits of the United States and Canada.
III. WARRANTY EXCLUSIONS: This warranty specifically does not apply to:
A.Any power converter which has been repaired or altered in any way by an unauthorized person or
service station;
B.Damage caused by excessive input voltage, misuse, negligence or accident; or an external force;
C.Any power converter installed in a vehicle used for commercial purposes;
D.Any power converter which has been connected, installed or adjusted or used other than in
accordance with the instructions furnished, or has had the serial number altered, defaced or removed;
E.Cost of all services performed in removing and re-installing the power converter; and
F.ANY LOST PROFITS, LOST SAVINGS, LOSS OF USE OF ENJOYMENT OR OTHER
INCIDENTAL DAMAGES ARISING OUT OF THE USE OF, OR INABILITY TO USE, THE
PRODUCT. THIS INCLUDES DAMAGES TO PROPERTY AND, TO THE EXTENT
PERMITTED BY LAW, DAMAGES FOR PERSONAL INJURY. THIS WARRANTY IS IN LIEU
OF ALL OTHER WARRANTIES, INCLUDING IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
IV. PROOF OF PURCHASE: A warranty claim must be accompanied by proof of the date of purchase.
V. CLAIM PROCEDURE: Upon discovery of any defect, Progressive Dynamics, Inc. shall be supplied the
following information by mail, telephone or fax, at the address listed below:
A.Name and address of the claimant;
B.Name and model of the power converter;
C.Name, year and model of the recreational vehicle in which the power converter was installed;
D.Date of purchase; and
E.Complete description of the claimed defect.
Upon determination that a warranty claim exists (a defect in material or workmanship occurring under normal
use and service,) the power converter shall be shipped postage prepaid to Progressive Dynamics, Inc. together
with proof of purchase. The power converter will be repaired or replaced and returned postage prepaid.
Progressive Dynamics Inc.
507 Industrial Rd.
Marshall, MI 49068
269.781.4241 Fax 269.781.7802
GENERAL INFORMATION
The INTELI-POWER 9100 series 120 VAC to 12 VDC power
converters are state-of-the-art electronic converter / battery
chargers. The INTELI-POWER 9100's are UL and CUL
(Canadian) listed.
Their compact size and quiet operation gives greater flexibility
in selecting the mounting location for either OEM installation
or after market replacement.
All INTELI-POWER 9100 series converters incorporate the
Total Charging Management System (TCMS) interface. The
TCMS interface connects the converter to optional devices that
can automatically control the output voltage of the converter
thereby controlling the charge rate to the batteries.
The converter has been designed and tested to provide
maintenance free operation. The INTELI-POWER 9100 line
of power converters have undergone tens of thousands of hours
of strenuous engineering testing to insure years of trouble free
operation.
GENERAL OPERATION
The INTELI-POWER series will supply "clean" nominal 13.6
VDC power from input voltages that range from 90-130 VAC.
Operates With or Without a Battery Connected, the output of
the INTELI-POWER 9100 converters are a regulated, filtered
D.C. voltage that can power sensitive electronics without the
need for a battery or other filtering.
NOTE
At normal input voltages the full load rated capacity is
available.
At input voltages less than 105 VAC the converter may not
supply full rated output capacity.
The full rated load (either 30,40,45, 55, 60 or 80 amps) is
available for load, battery charging or both. When functioning
as a regulated battery charger the INTELI-POWER 9100
converters have nominal voltage output of 13.6 VDC. The
system was designed to sense voltage on the battery and will
taper the charging current as the battery becomes charged.
When the INTELI-POWER 9100 senses the battery is at full
charge it will provide a trickle charge to maintain a full charge
condition.
CAUTION
IT IS IMPORTANT THAT THE FLUID LEVEL OF ANY
CONNECTED BATTERIES BE CHECKED ON A
REGULAR BASIS. ALL BATTERIES WILL “GAS”
AND LOSE SOME FLUIDS WHEN CONTINUOUSLY
CONNECTED TO ANY CHARGING SOURCE.
When the vehicle is to be stored for extended periods of time it
is recommended that the batteries be disconnected, unless one
of the optional devices are attached to the TCMS interface (see
the owners manual for that device for more information).
Re-connect once a month to maintain a full charge.
FEATURES
INTELLIGENT ... The INTELI-POWER 9100 thinks for
itself, by monitoring and sensing the load and ambient
conditions.
MULTIPLE BATTERY CHARGING ... INTELI-POWER
9100 has the capability of charging multiple batteries at the
same time! They can even charge a combination of different
capacity batteries.
GFCI PROTECTION ... INTELI-POWER 9100 has the
LOWEST ground fault leakage. With this unit, the user can
confidently utilize the RV's AC outlets without being
concerned about a ground fault interruption of the facilities
power source.
REVERSE BATTERY PROTECTION CIRCUIT ... If a
battery is accidentally hooked up backwards, the converter will
be protected. The PD9130 has one 30 AMP ATC automotive
style fuse. Models PD9160A, PD9155, PD9145A and
PD9140A have two 30 AMP ATC automotive style fuses.
Model PD9180 has three 30 AMP ATC automotive style fuses
mounted externally that will blow if a reverse battery condition
should occur. Note: if the unit has accessories plugged into the
TCMS interface the TCMS plug must be removed to provide
clearance to replace the fuses.
CAUTION
IF THE REVERSE BATTERY PROTECTION FUSES ARE
BLOWN DURING INSTALLATION, CHECK TO SEE
THAT THE BATTERY HAS BEEN CONNECTED
PROPERLY BEFORE REPLACING THE FUSES. REPLACE
THE FUSES ONLY WITH THE SAME TYPE AND RATING
AS THE ORIGINAL FUSES. USING OTHER FUSES
COULD RESULT IN THE CONVERTER BEING
DAMAGED, VEHICLE DAMAGE, INJURY OR OTHER
CONSEQUENCES (SEE WARRANTY).
SHORT CIRCUIT PROTECTION ... The "smart" converter,
INTELI-POWER 9100, senses, within millionths of a second,
if the output terminals have been shorted. If this condition
should occur the converter first limits the current. Should the
condition continue to exist the converter then reduces the
current output, within thousandths of a second. The
INTELI-POWER 9100 was designed to protect itself. Once
the "short circuit" has been corrected the INTELI-POWER
9100 will automatically return to normal operating conditions.
THERMAL PROTECTION ... If a over temperature
condition should occur due to air flow obstruction or improper
installation the INTELI-POWER 9100 senses the condition
and decreases power output until the unit returns to normal
operating temperature. Full output capacity will return as the
unit cools down.
IGNITION PROTECTION ... All INTELI-POWER 9100
series converters are ignition protected.
INTERNAL COMPONENT COOLING ... The system is so
efficient that if demand is less than 20% of the rated capacity,
the auxiliary cooling fan will NOT activate. This means that at
night when the power demand is reduced the fan may not come
on at all. The location of the fan allows for the maximum
cooling of both the case and components.
OVERVOLTAGE PROTECTION ... If the Input Voltage
exceeds a preset limit the converter will shut-down to prevent
damage. The unit will return to normal operation when the
voltage returns to normal
INSTALLATION INSTRUCTIONS
Horizontal mounting of the INTELI-POWER 9100, is
recommended although it can be mounted in any position
that provides unobstructed ventilation to the fan and vent
holes. Secure the converter firmly to the mounting
surface using standard fasteners.
The OEM should test the INTELI-POWER 9100 under
full load conditions in its intended mounting location.
This will insure that there is sufficient unobstructed
ventilation to the converter allowing it to operate at its
maximum rated load. Failure to provide adequate
ventilation to the converter will cause the converter to
cycle on and off as it responds to ambient conditions.
! ATTENTION !
USE A 5/32" HEX DRIVER TO TIGHTEN THE
OUTPUT SCREWS. DO NOT EXCEED 50 IN-LB
TORQUE. PD9160 AND PD9180 USE A SLOTTED
SCREWDRIVER TO TIGHTEN THE OUTPUT
SCREWS
THE OUTPUT TERMINALS ARE RATED FOR 2 TO
14 GA. COPPER OR ALUMINUM WIRE.
THE INTELI-POWER 9100 CONVERTERS ARE NOT
WEATHER TIGHT OR DESIGNED FOR WET
LOCATION MOUNTING. THEY MUST BE
PROTECTED FROM DIRECT CONTACT WITH
WATER.
THE INTELI-POWER 9100 CONVERTERS ARE NOT
DESIGNED FOR ZERO CLEARANCE
COMPARTMENTS.
DURING THE MANUFACTURING PROCESS
AVOID THE INTRODUCTION OF FOREIGN
MATERIALS INTO THE CASE AS THIS COULD
CAUSE A MALFUNCTION OF THE CONVERTER.
TROUBLE SHOOTING GUIDE
PROBLEM POSSIBLE CAUSES ACTION
1. No Output120 VAC supply not connectedConnect power supply
Check AC distribution panel for proper operation
External Fuses BlownCheck for Reverse Polarity
Replace Fuses with same type and rating
Short CircuitTrace RV Circuits for possible fault
Unit has shutdown due to overheatingCheck air flow
Allow unit to cool
Unit has shutdown due to over voltageCheck input voltage
(Also see Item 5 below)Converter will shut down if the input voltage exceeds 132
Volts
Correct Input Voltage
2. External Fuses
Blown
3. Converter cycles on
& off
4. Low OutputExcessive Load for ConverterReduce load requirements or Install Larger Converter
5. Intermittent or no
Output on Generator,
works on Shore
Power
Reverse Battery Hook UpCorrect Hook up and replace Fuses with same type and
rating
Compartment gets too hotCheck air flow to the converter
Improve Ventilation to the compartment
Input Voltage not between 105-130
VAC
Bad Battery Cell(s)Replace Battery
Unit has shutdown due to over voltage.Add another load to the generator, this may reduce the
Some generators exhibit excessive
voltage spikes on the AC power output,
this may cause the over voltage
protection to shut the unit down
Correct input supply voltage
“spikes” to an acceptable level
Contact generator manufacturer for possible defect in the
generator
Do not replace the converter unless the following checks have been performed:
1.Loosen the screw on the positive terminal and disconnect the positive wire. Read the converter output voltage using a
DC voltmeter. If the voltage is above 13 volts, the converter is working properly.
2.If the converter output is zero volts, use an AC voltmeter to check for proper voltage at the 120 VAC outlet that the
converter is plugged into. This voltage should be between 105 and 130 volts.
3.Check the fuses located at the front of the converter. These fuses will only blow if the battery or DC output leads
were connected in reverse, even for a moment. Replace the fuses and repeat step 1.
NOTE: When replacing fuse(s) the TCMS plug must be removed to provide clearance for fuse replacement.
PD9130
INPUT/OUTPUT SPECIFICATIONS
PD9140A
PD9145A
Input: 105-130 VAC 60 Hz
500 Watts
Output: 13.6 VDC, 30 Amps
Dimensions: 4.5H x 7L x 7.25W
Weight: 4lbs
PD9155
Input: 105-130 VAC 60 Hz
900 Watts
Output: 13.6 VDC, 55 Amps
Dimensions: 4.5H x 10L x 7.25W
Weight: 5.4lbs
Input: 105-130 VAC 60 Hz
600 Watts
Output: 13.6 VDC, 40 Amps
Dimensions: 4.5H x 8.625L x 7.25W
Weight: 4.5lbs
PD9160A
Input: 105-130 VAC 60 Hz
1000 Watts
Output: 13.6 VDC, 60 Amps
Dimensions: 3.6H x 9.15L x 9W
Weight: 5.8lbs
Input: 105-130 VAC 60 Hz
725 Watts
Output: 13.6 VDC, 45 Amps
Dimensions: 4.5H x 8.625L x 7.25W
Weight: 4.5lbs
PD9180
Input: 105-130 VAC 60 Hz
1300 Watts
Output: 13.6 VDC, 80 Amps
Dimensions: 3.6H x 11.65L x 9W
Weight: 7.5lbs
CAUTION RISK OF
FIRE:
Chassis bonding wire must
be a separate wire ran
directly to chassis from the
Grounding Lug provided
on the side of the
converter. DO NOT
connect Output negative
to chassis using the same
wire.
109205 REV L 10/02
Loading...